Panasonic Color Cctv Camera Wv Cw384 Operating Instructions

11
4. Secure the camera to the camera mount bracket with the 3 camera fixing screws (accessories).
5. Remove the screw from the mounting boss for safety wire of the camera mount bracket and secure the safety wire with the
screw.
Important:
• Ensure that the safety wire is firmly secured. Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}
Important:

• To install this product outdoors, be sure to
waterproof the cables. The camera main
body is waterproof, but the mount bracket
and adapter box are not...

12
xSecure the camera mount bracket
• When the camera is directly installed on a wall
Use 4 screws (locally procured) to secure the camera
mount bracket to a wall or a junction box (locally pro-
cured).
Mounting screw x4 (locally procured)Camera mount bracket
22 mm
{7/8}
46 mm {1-13/16}
83.5 mm
{3-1/4}
Cable access hole
6 mm (W) x 10 mm (L) {1/4 (W) x 3/8 (L)}
(long hole)
Mounting screw x4 (locally procured)Junction boxe
s
Camera mount bracket
46 mm {1-13/16}
83.5 mm
{3-1/4}
6 mm (W) x 10 mm (L) 
{1/4...

13
2. Attach the camera mount bracket to the left
or right hinges of adapter box.
Mount bracket
Adapter boxHinges
Mounting screw for adapter box/
camera mount bracket x4 (M5 x 20)
Adaptor box mounting screw (M4 x 35)
SDII
cSecure the mount bracket covers to the
camera mount bracket with the 2 mount
bracket cover screws (accessories).
Mount bracket cover screw x2 
(M3 x 6) (accessories)Camera mount 
bracket Mount bracket cover x2
Note:
• The right or left hinges of the adapter box shall be
selected so as...

14
Video output connection
The video output connector is connected to the monitor or
other system devices with a coaxial cable (locally pro-
cured).
The maximum extensible length is shown in the table.
* When using 12 V DC power supply, 
the heater is unavailable.To 24 V AC or 12 V DC 
power supply
Video output cable 
(Approx. 72 cm {28-3/8})
Brown (Live)
Blue (Neutral)
Green/Yellow (GND)
To GND
BNC connector
BNC connector
To VIDEO IN Power cord 
(Approx. 72 cm {28-3/8})
BNC connector
vMake a connection...

15
bBe sure to view the monitor for adjustment
when the camera angle is adjusted.
Supply power to this unit, connect the monitor for adjust-
ment (e.g. a small LCD) to the monitor output connector,
and adjust the camera angle (turn off the power after view
angle adjustment for safety).
1. Loosen the 4 fixing screws of the lens cover to remove
the lens cover.
2. Connect the monitor for adjustment to the monitor out-
put jack.
Note:
• The plug dimensions in the illustration below shall be
observed for the...

16
nAdjust the focus
Focus adjustment must be performed when camera angle
(page 15) adjustment are performed.
1. Repeat the steps (1) and (2) to adjust the view angle
and focus.
(1) Rotate the zoom adjustment ring to adjust the view
angle between TELE and WIDE.
(2) Loosen the focus lock knob, make coarse adjust-
ment of the focus, and then tighten the focus lock
knob.
2. Press the auto back focus button after adjusting the view angle while viewing the monitor
for adjustment.
→The focus position...

17

1. Loosen the 1 fixing screw of the rear cover to remove the rear cover.
2. Loosen the 2 fixing screws of the switch cover to remove the switch cover. 
3. Hold down the setting button for 2 seconds or more to call up the top screen of the setup menu. And then adjust the
back focus. For further information, refer to page 35.
mMount the cover
1. Attach the desiccant (accessory) to the inner bottom side of the lens cover. 
2. Mount the lens cover, switch cover, and rear cover.
Important:
• The...

18
,Mount the sunshield
Mount the sunshield on the camera with the 4 sunshield mounting
screws (accessories).
Camera main body SunshieldSunshield mounting screw x4 (M3 x 6) (accessories)
SDIII
Align the arrow 
to lens direction.
Notes:
• Be sure to use the 4 sunshield mounting screws (accessories). Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}
• The FRONT side of the sunshield shall be on the lens side. 
.When the mounting surface is changed to the top surface of the camera body
1. Remove the 4...

19
⁄0When the tripod socket (accessory) is used (when a different camera mount bracket is used)
1. Remove the 4 tripod head fixing screws from the camera body and remove the tripod head.
Disassemble the tripod head and pull out the video output cable and power cord.
2. Mount the tripod socket (accessory) with the 4 mounting
screws for tripod socket (accessories).
Sunshield mounting screw x4 (M3 x 6) (accessories)
Rear part of sunshield
2. Mount the tripod socket 
(accessory). 
Mounting screw 
for tripod...

20
3. Use a safety wire (locally procured) to take measures against a fall of the camera according to the installation position.
Camera mount bracket Safety wire
For wall installation WV-831 WV-Q140
For ceiling installation WV-7010A WV-Q141
4. Hook the tip (ring portion) of the safety wire on the sunshield mounting stud and screw the sunshield to secure the safety
wire. 
5. Refer to the instructions of the safety wire for the following steps. 
Important:
• Be sure to use the 4 mounting screws for tripod...