Panasonic Color CCTV Camera Wv Cs580 Wv Cs584 Installation Guide

11
Major operating controls 
Power Cable 
Video Output Connector 
Decorative Cover 
Dome Fix Ring 
Safety Wire 
Lens
The lens cannot be replaced. 
The dome cover is easily damaged,   
And should be handled with care. 
Data Port (RS485) 
Alarm Output Connector 
Alarm Input Connector 
Camera Mounting Base 
Dome Cover
Camera
WARNING
IMPORTANT 

12
DIP switch settings 
 Communication Parameters (DIP Switch 2) 
The factory default settings are all OFF. Switch 1: Terminator (Internal Termination Resistance)
  Set to ON in the following situations.
   When 1 camera is connected to this unit 
   When 2 or more cameras are connected to this unit that works as a termination
Switches 2 to 4: Communication Parameters This setting toggles between 2-line and 4-line communication. Use 
these switches to select the communication protocol being used. 
1234...

13
 Unit Number (DIP Switch 1) 
The factory default settings of these DIP switches are all OFF. (Coaxial Multiplex System)  
Configuration for using  Panasonic Protocol
1234 
ON
5678
DIP Switch 1 Unit  
Number
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234...

14
1234 
ON
5678
DIP Switch 1 Unit  
Number
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234
ON
5678
1234
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234
ON
5678
DIP Switch 1 Unit  
Number DIP Switch 1 Unit  
Number
69 
70
71
72
73
74
75
76
77 
78 
79
80
81
82
83
84
85
86 
87 
88
89
90
91
92
93
94
95
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234 
ON
5678
1234
ON
5678
1234...

15
Important:  
 When using Pelco protocol, make sure that the system works properly before use. Some functions using Pelco  
protocol may be restricted when this camera and the apparatuses (commercially available) compatible with 
Pelco protocol operate together. 
Note: 
 When using the Unit Number 1 to 96 of Panasonic Protocol and using the Unit Number 32 to 96 of Pelco-D  
protocol, the unit number setting needs to be configured using the RS485 SET UP menu. For details about 
configuring this setting,...

16
Camera Installation
When installing the camera on a wall or a ceiling, please read the important notice below. 
Important: 
Procure 4 screws (M4) to secure the camera to a wall or a ceiling according to the material of the installation 
area. In this case, wood screws and nails should not be used. For mounting a camera on a concrete wall, use 
an anchor bolt (for M4) or an AY plug bolt (M4) for securing. (Recommended tightening torque: 1.6 N·m)

 reinforced or the Ceiling Mount Bracket for the camera,...

17
  Preparing the Camera andDecorative Cover for Side Cable Exit
The camera and decorative cover should be prepared 
as shown below when mounting the camera on a 
ceiling or wall with its cables (power, video output, 
RS485, alarm in, alarm out) exiting from the side. 
Perform this task when using Ceiling Mount Bracket 
WV-Q126, or Wall Mount Bracket WV-Q118.
The camera mounting base needs to be removed in 
order to prepare the camera. See steps 1 and 2 below 
for information about how to remove the...

18
5.  Connect the cables. 
Please refer to page 20 for the details of connections.
6.  Attach the safety wire for securing the camera to the 
camera mounting base. 
Pull on the safety wire to make sure its ring is securely 
connected to the camera mounting base hook. 
If the dust protect sheet that comes with the camera 
is affixed to the camera mounting base, remove it 
before performing the above step. 
Safety   wire ring 
Note:   
 
to hang from it. Do not apply force greater than 
the weight of the...

19
Uninstalling the Camera
Caution:  
 
and exactly when uninstalling the camera and 
decorative cover. Failure to do so creates the risk 
of damage to the camera.  
   Removing the Decorative Cover
Note that you need to separate the two parts of the  
decorative cover in order to remove it. 
 1.  Unhook the two parts of the decorative cover. 
    Press upwards on the decorative cover at the points  
marked    (indicated by the arrows, in the  illustration below) to unhook the two parts from  
each...

20
Connections 
Precautions 
   The following connections should be made by qualified service personnel or system installers in accordance  with all local codes.   See the reverse side of the cover page for main lead connection.   Turn off the power at the fuse box before starting the installation work, or it so could result in fire, electric shock, personal injury, and material damage. 
RS485 Data PortAlarm Input ConnectorAlarm Output Connector
T(B)T(A)R(B)R(A)
Red Orange Yellow Green
Data 
Data...