Panasonic Color CCTV Camera Wv Cp600 WV CP620 WV CP604E WV CP624E Series Installation Guide

21
The recommended wire size for 24 V AC power cord is shown below:
12 V DC
Calculation of the relation among the cable length, resistance, and power supply. 
The voltage supplied to the camera shall be between 10.8 V DC and 16 V DC. 
10.8 V DC ≤ VA - 2 (R x I x L) ≤ 16 V DC 
L: Cable length (m)
R: Resistance of copper wire (Ω/m) 
VA: DC output voltage of power supply unit
I: DC current consumption (A)
    See specifications.  
Resistance of copper wire [at 20 °C]
k Adjust the camera angle by loosening...

22
 4 When the focus ring is positioned near the best focus position, the position will  
automatically be memorized as the "PEAK HOLD" position (the higher the value is, the 
closer it is to the focus point).
 5 When the focus ring is moved, the current focus position will be indicated on 
"INDICATOR". Adjust the focus position so that the indicator value goes close to the 
"PEAK HOLD" position.
 6 When the indicator value goes to the best focus position, "BEST FOCUS"...

23
Setup menu
Performing each setting item in the setup menu should be completed in advance to use this unit. Perform  
the settings for each item in accordance with the installation conditions and customer requirements.
List of setup menu
Setup itemDescription
CAMERA IDThis item specifies the camera title. The camera title that indicates the  camera location and other information about the camera is created with alphanumeric characters and symbol, and then displayed on the screen.
CAMERAPerforms the...

24
Screenshot 1
Hold down the [SET] button for about 2  
seconds to call up the top screen of the setup 
menu. 
     MODEL   WV-CP620 SERIES CAMERA ID     OFFCAMERA   SYSTEM SPECIAL LANGUAGE 
  
 END   SETUP DISABLE
Screenshot 2
The setup mode changes to "ENABLE", and  
the setup menu becomes ready to be set.   
 MODEL   WV-CP620 SERIES CAMERA ID     OFFCAMERA   SYSTEM SPECIAL LANGUAGE 
 END   SETUP ENABLE
    
Step 1
Press the [UP] or [DOWN] button to move the  
cursor to "END".
Step 2...

25
Screenshot 3
The selected setup screen in the setup menu  
appears on the screen.  
     **CAMERA SETUP**  SCENE1 ALC/ELC      ALC     SHUTTER      OFF AGC          ON(HIGH) SENS UP      OFF WHITE BAL    ATW1 DNR          HIGH D&R(IR)       AUTO1 VMD          OFF 
 RET TOP END
Note:
 • If  the  top  screen  of  the  setup  menu  is  
called up with the operation buttons 
while the camera is operated, the setup 
mode is always "DISABLE" to prevent 
operation errors.
   To perform settings in...

26
Top screen“CAMERA ID” screen
“CAMERA SETUP” screen
“SYSTEM SETUP” screen
“SPECIAL SETUP” screen
“LANGUAGE SETUP” screen 
 MODEL   WV-CP620 SERIES CAMERA ID     OFFCAMERA   SYSTEM SPECIAL LANGUAGE 
  
 END   SETUP DISABLE
   **LANGUAGE SETUP** 
LANGUAGE      ENGLISH 
 SET  RET TOP END
     **CAMERA ID**         0123456789     ABCDEFGHIJKLM     NOPQRSTUVWXYZ     ().,:;&#!?=     +-*/%$
    SPACE POSI    RET TOP END RESET 
    ................
    **SYSTEM SETUP**  SYNC          INT 
PRIVACY ZONE  OFF...

27
Screen transition diagram
CP620
CP620
CP600
Top screen“CAMERA ID” screen
“CAMERA SETUP” screen
“SYSTEM SETUP” screen
“SPECIAL SETUP” screen
“LANGUAGE SETUP” screen 
 MODEL   WV-CP600 SERIES CAMERA ID     OFFCAMERA   SYSTEM SPECIAL LANGUAGE 
  
 END   SETUP DISABLE
   **LANGUAGE SETUP** 
LANGUAGE      ENGLISH 
 SET  RET TOP END
     **CAMERA ID**         0123456789     ABCDEFGHIJKLM     NOPQRSTUVWXYZ     ().,:;&#!?=     +-*/%$
    SPACE POSI    RET TOP END RESET 
    ................
    **SYSTEM...

28
 • Are the power cord and coaxial cable  connected appropriately?
  →  Check whether the connection is   appropriately established.
 • Is the monitor brightness appropriately  adjusted, or is the contrast appropriately adjusted?
  →  Check whether the monitor settings   are appropriate.
Troubleshooting
Before asking for repairs, confirm the causes with the following table.  
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the  
table or a problem is not...

29
Specifications
WV-CP620/GWV-CP600/GWV-CP624EWV-CP604E
Power source220 V - 240 V AC 50/60 Hz24 V AC 50/60 Hz, 12 V DC
Power consumption2.8 W24 V AC: 2.5 W, 12 V DC: 220 mA
Image sensor1/3-type interline transfer CCD
Effective pixels976 (H) × 582 (V)
Scanning area4.8 mm (H) × 3.6 mm (V)
Scanning system2:1 interlace
Scanning line625 lines
Horizontal scanning frequency15.625 kHz
Vertical scanning frequency50.00 Hz
SynchronizationInternal (INT)
Horizontal resolution650 TV lines
Vertical resolution400 TV...

30
CD-ROM* ..........................................................................1  pc. 
Installation Guide (this book) ..............................................1 pc.
* The CD-ROM contains the operating instructions and installation guide (PDF). 
The following parts are used during installation procedures: 
Power cord (only for WV-CP600/G and WV-CP620/G) 
  (Approx. 1.8 m) ...........................................................1 pc.
Power cord plug 
(only for WV-CP604E and WV-CP624E)...