Panasonic Color Cctv Camera Wv Cp300 Operating Instructions

11
2	Light	quantity	control	method	selection	[ALC/ELC]	
The method of controlling the quantity of light is selected from the following in accordance with 
the lens to be used. 
ALC (default): The  iris  of  the  lens  is  automatically  adjusted  in  accordance  with  the  brightness 
of a subject. Select "ALC" when using an ALC lens. 
ALC+:  Controls  the  quantity  of  light  with  a  combination  of  the  electronic  shutter  and  auto  iris.  This 
selection  is  suitable  at  shooting  a...

12
Note:
	 •	 When	“BLC”	is	set	to	“ON”,	“ABS”	displays	“---”	and	may	not	be	operated.	
Step 4
When "BLC" is set to "OFF", bright areas of an image are masked to facilitate the visibility of 
dark areas. 
Move the cursor to "MASK SET" and press the [SET ] button.
→ The mask setting screen appears. 
Step 5
Use the [UP], [DOWN], [RIGHT], and [LEFT] buttons to move the flashing cursor to the area to 
be masked and press the [SET] button. 
When the selected area is masked, the masked...

13
Note:
	 •	 When	"SENS	UP"	is	set	to	the	AUTO	mode,	“AGC”	cannot	be	set	to	“OFF”.
5	Electronic	sensitivity	enhancement	setting	[SENS	UP]
Use  of  the  electronic  sensitivity  enhancement  function  increases  the  light  sensitivity  of  the 
CCD,  and  accordingly  the  image  becomes  brighter.  The  magnification  is  unchanged  for  selec-
tion  of  FIX,  and  the  magnification  is  automatically  adjusted  in  accordance  with  the  illuminance 
of  a  photographic  subject  for...

14
Step 1
Set "WHITE BAL" to "AWC" and press the [LEfT] button to change to "AWC → PUSH SET". 
Step 2
Press  the  [SET ]  button  and  adjust  the  white  balance.  "AWC  →  PUSH  SET"  is  reversely  high-
lighted during adjustment. When the reversely highlighted display is restored, the white balance 
adjustment is completed. 
Step 3
Press  the  [rIgHT ]  button  to  select  "AWC".  refer  to  this  page  for  fine  adjustment  of  the  white 
balance. 
Note:
	 •...

15
Step 4
Move the cursor to "POSITION" and press the [SET ] button. 
Step 5
Press the [uP], [dOwN], [rIghT] and [lEfT] buttons to move to the upper-left part of the area 
to be set, and press the [SET ] button. 
Step 6
Press the [uP], [dOwN], [rIghT ] and [lEfT] buttons to move to the lower-right part of the area 
to be set, and press the [SET ] button.
7 Digital noise reduction function setting [DNR]
The digital noise reduction function reduces noise automatically under the condition of low...

16
CP310
CP310
CP300 AUTO:   Similar to the basic functions of AUTO1, but does not change the IR filt\
er. 
    Switches  to  black-and-white  images  when  brightness  (illuminance)  around  the 
camera is lower than approx. 0.1 lx.
  OFF (default): Displays color images.
Note:
	 •	CP310
CP310
CP300
 When “AUTO1” or “AUTO2” is selected, it is recommended to set “AGC” to “ON”.
	 •	 If 	a 	subject 	is 	always 	moving 	or 	the 	screen 	is 	occupied 	with 	a 	uniform 	color, 	brightness	
determination  may...

17
Note:
	 •	 Images	may	not	be	displayed	 appropriately	 without	burst	signals	 when	camera	 images	are	
displayed in the black-and-white mode depending on a monitor or VCR model to be used. 
In such a case, set the burst signal output to "ON". 
9 VMD setting [VMD] 
The  VMD  function  allows  the  camera  to  detect  object  motion  and  hindrance  to  the  camera. 
Detection  of  object  motion  or  hindrance  to  the  camera  can  be  announced  by  issuing  an  alarm 
signal. 
Important:
	 •...

18
Step 2
Move the cursor to "MASK SET" and press the [SET ] button. 
→ The “MASK SET” screen appears.
In  the  masked  area,  no  alarm  will  be  issued  even  if  a  moving  object  is  detected.  The  masked 
area is set in the same way as the masked area setting in Light quantity control method selec-
tion. (
 page 11)
Step 3
Hold down the [SET ] button for more than 2 seconds after completion of masking.
→ Return to the previous menu. 
Step 4
Move the cursor to "ALARM", press the...

19
Step 6
Move the cursor to “Level”. Use the [RIGHT] or [LEFT] button to adjust the level. 
Repeat step 5 and 6 to adjust to optimal level. 
Step 7
Move the cursor to “DWELL TIME ”. Select the dwell time from the following.
2 S (default)/5 S /10 S /30 S 
Alarm  signal  will  be  issued  once  a  continuously  moving  object  is  detected  within  the  specified 
time. 
Setting of scene change detection 
This  function  detects  a  change  in  the  subject  state  that  occurs  by  covering  the  camera...

20
Camera system setting [SYSTEM SETUP] 
Performs the settings relating to the camera system such as synchronization and privacy zone. 
The  following  settings  can  be  configured  on  the  "SYSTEM  SETUP"  screen  displayed  from  the 
top screen. Refer to page 5-6 for how to call up the screen. 
“SYSTEM SETUP” screen
    **SYSTEM SETUP** 
SYNC          INT
PRIVACY ZONE  OFF
STABILIZER    OFF
EL-ZOOM       OFF
UPSIDE-DOWN   OFF
  -     +
LDC           I......  0
 RET TOP END
@ Synchronization...