Panasonic Color CCTV Camera Wv Cf614 Wv Cp600 Operating Instructions

11

Screen when SCENE1 is selectedScreen when SCENE2 is selected
    **CAMERA SETUP** 
SCENE1
 ALC/ELC    ALC    
 SHUTTER    OFF
 AGC        ON(HIGH)
 SENS UP    OFF
 WHITE BAL  ATW1
 DNR        HIGH
     AUTO1
 VMD         OFF
 RET TOP END
D&N(IR)     **CAMERA SETUP** 
SCENE2
COPY(SCENE1)  ALC/ELC    ALC    
 SHUTTER    OFF
 AGC        ON(HIGH)
 SENS UP    OFF
 WHITE BAL  ATW1
 DNR        HIGH
     AUTO1
 VMD         OFF
 RET TOP ENDD&N(IR)

CP600

Camera operation setting [CAMERA SETUP]
The following...

12
About Super Dynamic 6 Functions
If there is high contrast between the bright and dark areas 
in a shooting zone, the dark area becomes less visible 
because the camera adjusts the iris in accordance with the 
bright area. Conversely, adjusting the lens brightness for the 
darker areas causes the brighter areas to become washed 
out. The SUPER DYNAMIC function digitally combines an 
image that is set up for a clear view of the brighter areas 
with an image that is set up for a clear view of the darker...

13
Step 4
Press the [UP], [DOWN], [RIGHT], and [LEFT] buttons to move the flashing cursor to the area to be masked and press the [SET] 
button. 
When the selected area is masked, the masked area will start blinking (between stripes and white). When the flashin\
g cursor is moved 
to other areas, the masked area will be displayed in white. 
Repeat the above procedure to mask other areas as necessary.
Note:
	 •	 To 	cancel 	the 	masking, 	select 	the 	masked 	area 	to 	be 	canceled, 	and 	then 	press 	the...

14
Note:
	 •	 When	“ALC/ELC”	is	set	to	“ELC”	or	“ALC+”,	only	the	AUTO	mode	is	enabled.		
	 •	 When	“SHUTTER”	is	set	to	options	other	than	“OFF”,	the	electronic	sensitivity	enhancement	setting	cannot	be	performed	and	“---” appears.
	 •	 When	the	magnification	of	“SENS	UP”	is	increased,	the	screen	becomes	coarser,	more	whitish,	or	more	flawed.	However,	this	 phenomenon is normal.
6. White balance setting [WHITE BAL] 
The white balance adjustment is selectable from the following.
ATW1 (default):  Activates...

15
Manual fine adjustment of white balance 
The white balance is manually fine adjusted after white balance automa\
tically adjustment in the automatic color temperature tracking 
mode (ATW1, ATW2) or automatic white balance control mode (AWC). 
Follow the procedures below. 
        **ATW1**(1)R
              -      +
B
              -      +
AREA 
 RET TOP END
**ATW1 AREA**(1)
  POSITION        PUSH SET
 RET TOP END
Area setting screen
 RESET   
... I...  
0
... I...  
0
“CAMERA SETUP” screen Fine...

16

AUTO1
 **D&N(IR) **(1)
LEVELHIGHDURATION TIME                S   L
BURST(BW)ON
 RET TOP END
.
I..
“CAMERA SETUP” screen “D&N (IR)” screen 
    **CAMERA SETUP** 
SCENE1
 ALC/ELC    ALC    
 SHUTTER    OFF
 AGC        ON(HIGH)
 SENS UP    OFF
 WHITE BAL  ATW1
 DNR        HIGH
     AUTO1
 VMD         OFF
 RET TOP END
D&N(IR)

Step 1
Move the cursor to “D&N (IR)” and select the mode from the following. 

CP620
 AUTO1 (default):   Automatically switches between color and...

17

Step 5
Move the cursor to “BURST (BW)”, and decide whether or not to pr\
ovide a burst signal output in the black-and-white mode. 
ON (default): Provides a burst signal output. 
OFF: Does not provide any burst signal output. 
Note:
	 •	 Images 	 may 	 not 	 be 	 displayed 	 appropriately 	 without 	 burst 	 signals 	 when 	 camera 	 images 	 are 	 displayed 	 in 	 the 	 black-and-white 	
mode depending on a monitor or VTR model to be used. In such a case, set\
 the burst signal output to “ON”. 
9....

18

Step 2
Move the cursor to “MASK SET” and press the [SET] button. 
→  The mask setting screen appears.

“MOTION DET” screen 
Mask setting screen
 **MOTION DET**(1)

 RET TOP ENDLEVEL
2S 
OFF 
DWELL TIME
DISPLAY MODE 
  ALARM
MASK SET

.... I.. 
20              -     +

In the masked area, no alarm will be issued even if a moving object is detected. The mas\
ked area is set in the same way as the 
masked area setting in “Light quantity control method selection”. (
 page 12)
Step 3
h
old down the...

19

Setting of scene change detection 
This function detects a change in the subject state that occurs by cover\
ing the camera with a cloth, a cap, or others, or by changing 
the camera direction largely.
Follow the procedure below.

“CAMERA SETUP” screen
 VMD        SCENE C HAN GE
    **CAMERA SETUP** 
SCENE1
 ALC/ELC    ALC    
 SHUTTER    OFF
 AGC        ON(HIGH)
 SENS UP    OFF
 WHITE BAL  ATW1
 DNR        HIGH
     AUTO1
 RET TOP END

D&N(IR)

Step 1
Move the cursor to “VMD” and press the [righ T...

20
Camera system setting [SYSTEM SETUP] 
Performs the settings relating to the camera system such as synchronization, alarm input/output terminal and privacy zone. The 
following settings can be configured on the “SYSTEM SETUP” screen displayed from the top screen. 
Refer to page 5 for how to call up the screen. 
10. Synchronization method [SYNC]
Only internal synchronization (INT) can be used. 
Multiplexed vertical drive (VD2) synchronization cannot be used.
11. Alarm input/output terminal setting...