Panasonic Color CCTV Camera Wv Cf344 Wv Cp300 Operating Instructions

							21
Step 2
Move the cursor to “PUSH SET” of “ZOOM” and press the [SET] button. 
→  The zoom setting screen appears. 
Step 3
Adjust the angular field of view by changing the electronic zoom factor (up to 2x) using the [UP] or [DOWN] button, and press the [SET] 
button. 
Note:
	 •	 When	the	zoom	factor	is	incremented,	resolution	will	be	deteriorated.	
Step 4
Move the cursor to “PUSH SET” of “PAN/TILT” and press the [SET] button. 
→  The pan/tilt setting screen appears. 
Step 5
Press the [UP], [DOWN], [RIGHT], and [LEFT] buttons to determine the position of the area to be set and press the [SET] button. 
The position can be changed in the range of zoom factor set in the zoom \
setting screen. 
14. Upside-down setting [UPSIDE-DOWN] 
ON: The video image can be reversed upside down. 
OFF (default): The video image cannot be reversed upside down.
15. Lens distortion correction [LDC]
The image may be distorted depending on the lens used and the zoom facto\
r. By adjusting the lens distortion correction setting, the 
distorted image can be converted to match the square monitor and achieve effects desired by the user. 
Note:
	 •		 	Depending	on	the	lens	used,	complete	correction	may	not	be	achieved.	
16. Focus setting [FOCUS]  CF354 
Sets the focus adjustment method and performs fine adjustment.
Follow the procedure below. 
Important:
	 •	 When	focus	missing	occurs	due	to	secular	change	in	the	lens	and	installation	environment	or	peripheral	temperature	change,	the	
focus adjustment is required again. 
Step 1 
Move the cursor to “ABF  PUSH” of “FOCUS” and press the [SET] button. 
 The focus function provides focus adjustment to automatically focus on a subject located in t\
he center of the screen. 
Step 2 
To fine adjust the focus, select “MANUAL” of “FOCUS”, press the [SET] button, and press the [RIGHT] or [LEFT] button to adjust the focus manually.  
						

							22
Important:
	 •	 The	following	are	recommendation	for	focus	setting	in	accordance	with	subjects.	
For such case (subject conditions)Select this (recommendation) 
	 •	 Normal	subject	“ABF”
	 •	 Frequently	moving	subject	Fine adjustment with "MANUAL" setting after “ABF” . 
	 •	 Subject with large illuminance change 
	 •	 Subject	with	low	illuminance	
	 •	 Too	bright	or	reflective	subject	
	 •	 Subject	through	a	window
	 •	 Place	where	the	lens	easily	becomes	dirty
	 •	 Subject	with	less	contrast	such	as	white	wall
	 •	 Subject	with	remarkable	depth
	 •	 Subject	with	heavy	flicker
	 •	 Subject	with	horizontally	parallel	lines	such	as	a	shutter 
						

							23
Special menu setting [SPECIAL SETUP] 
The special menu setup is performed including the setting of the camera \
image quality and the communication configuration when a 
receiver is used. The following settings are to be configured on the "SPECIAL SETUP" screen displayed from the top screen. 
Refer to page 5 for how to call up the screen. 
17. Chroma level adjustment [CHROMA GAIN] 
Press the [RIghT] or [LEfT] button to adjust the color density of the camera image. When the level\
 indicator moves in the "+" 
direction, the color becomes deeper, and when the level indicator moves in the "–" direction, the color becomes lighter. Be sure to 
view a vector chromaticity indicator or a video monitor when the adjustment is performed.\
 
18. Aperture level adjustment [AP GAIN]
Press the [RIghT] or [LEfT] button to adjust the image quality. When the level indicator moves in the "+" direction, the image 
becomes sharper, and when the level indicator moves in the "–" direction, the image becomes softer. Be sure to view a video monitor 
when the adjustment is performed.
Note:
	 •		Moire	(interference	fringes)	may	be	observed	when	shooting	a	subject	with	fine	pattern	such	as	a	carpet	or	a	curtain.	In	such	a	case, move the indicator in the "-" direction to reduce moire. 
19. Pedestal level adjustment [PEDESTAL] 
Press the [RIghT] or [LEfT] button to adjust the pedestal level of the camera. When the level indi\
cator moves in the "+" direction, 
the image becomes brighter, and when the level indicator moves in the "–" direction, the image becomes darker. Be sure to view a 
waveform monitor or a video monitor when the adjustment is performed. 
20. Chroma phase (hue) adjustment [HUE] 
Press the [RIghT ] or [LEfT ] button to adjust the hue of the camera image. Be sure to view a vector chromaticity indicator or a video 
monitor when the adjustment is performed. 
21. Pixel compensation [PIX OFF] 
flaws of pixel in the displayed camera image are corrected. Up to 16 points can be corrected. 
follow the procedure below. 
      **PIX OFF**
  1     2     3     4
  5     6     7     8
  9    10    11    12
 13    14    15    16
1
DEL 000 000
SPECIAL SETUP screen “PIX OFF” screenPixel compensation positioning screen
 RET TOP END
   **SPECIAL SETUP**
CHROMA GAIN   ...
.I..160
AP GAIN        ...I... 32
PEDESTAL       .I.
.
... 15
PIX OFF
CAMERA RESET  PUSH SET
 SER.NO. XXXXXXXX COMMUNICATION COAX
 RET TOP END
              -     +
HUE           ...I...  0
Step 1
Move	the	cursor	to	“PIX	OFF”	and	press	the	[SET]	button.	
→ 	The	“PIX	OFF”	screen	appears.	
SPECIAL 
SETUP screen
   **SPECIAL SETUP**
CHROMA GAIN    ...
.I..160
AP GAIN        ...I... 32
PEDESTAL       .I.
.
... 15
              -     + PIX OFF
CAMERA RESET  PUSH SET
 SER.NO. XXXXXXXX COMMUNICATION COAX
 RET TOP END
HUE            ...I...   0 
						

							24
Step 2
Select a number (1 to 16) with which a pixel compensation point is registered and press the [SET] button. 
→  The pixel compensation positioning screen appears. 
Step 3
Press the [UP], [DOWN], [RIGHT], and [LEFT] buttons to move the crosshair cursor to the center of the flaw to be corrected and press 
the [SET] button. 
→   The flaw is corrected and the pixel compensation point is registered. The “PIX OFF” screen appears again. An asterisk “*” is 
attached at the right side of the number when registration is completed. The coordinate is expressed in figures. 
Note:
	 •		To	clear	the	registered	pixel	compensation	point,	move	the	cursor	to	“1”	of	the	right	of	“DEL”,	use	the	[RIGHT] and [LEFT] buttons 
to select the number with which the target pixel compensation point is r\
egistered and press the [SET] button. The registered pixel 
compensation point is cleared, and an asterisk “*” at the right side of the number disappears\
. 
22. Communication setting [COMMUNICATION] CP310
CP310
CP300
 
CP310
CP310
CP300 
The required communication configuration is performed to use this unit integrate\
d into the system with a receiver. 
COAX (RCV): When using our receiver (e.g. WV-RC150). 
COAX (default): When not using any receiver. 
23. Default resetting [CAMERA RESET] 
The settings in the setup menu are restored to the default settings. 
Move the cursor to “ → PUSH SET” of “CAMERA RESET” and hold down the [SET] button for\
 more than 2 seconds to enter the 
“RESET?” screen. 
To return to the previous screen without resetting, move the cursor to “NO” and press the [SET] button. To restore the default 
settings, move the cursor to “YES” and press the [SET] button. 
Note:
	 •		The	data	of	the	registered	pixel	compensation	points	is	not	cleared.		
	 •		To	set	whether	to	reset	the	camera,	select	“YES”	or	“NO”	by	using	the	[SET]	button.	To	set	with	a	controller,	refer	to	the	instruc-
tion manual of the controller. 
24. Serial number viewing [SER.NO.] 
Displays the serial number of this product.  
						

							
25

Camera language selection [LANGUAGE SETUP]
A language for the setup menu is selected from the following: The language selection can be made on the “LANGUAGE\
 SETUP”
screen displayed from the top screen. 
Refer to page 5 for how to call up the screen.  
Move the cursor to “LANGUAGE” and press the [R i G h T ] or [ LE f T ] button to select the target language, then move the cursor to “SET”\
, 
and press the [SET] button. 
Select the target language from the following. 
JAPANESE/ENGLISH (default)/FRANÇAIS/ESPAÑOL/DEUTSCH/ITALIANO/ PУCCKИЙ/中文
 
Note:
	 •	 	When 	 the 	 language 	 is 	 changed, 	 the 	 specified 	 camera 	 title 	 is 	 cleared. 	

“LANGUAGE SETUP” screen 
   **LANGUAGE SETUP**
LANGUAGE      ENGLISH
 SET
 RET TOP END 
						

							26
Shortcut operation 
Use of a system controller with the “Camera function” button allows users to perform th\
e shortcut settings with use of the numeric 
keypad and camera function button. The available shortcut operations wit\
h this unit are shown as follows. System	controller	operation	 Setting	contents
[9]	+	[0]	+	[Camera	function]		 Black-and-white	control	(D&N)	ON	
CP310
CP310
CP300 
[9]	+	[1]	+	[Camera	function]		 Black-and-white	control	(
D&N) OFF
[9]	+	[2]	+	[Camera	function]   Black-and-white control (D&N) AUTO1
 CP310
CP310
CP300 
   Black-and-white control (
D&N) AUTO 
CP310
CP310
CP300 CF354  CF344

[9]	+	[3]	+	[Camera	function]		 Camera	title	(CAMERA	ID)	ON
[9]	+	[4]	+	[Camera	function]		 Camera	title	(CAMERA	ID)	OFF
[9]	+	[8]	+	[Camera	function]		 Electronic	zoom	ON
[9]	+	[9]	+	[Camera	function]		 Electronic	zoom	OFF
[1]	+	[6]	+	[8]	+	[Camera	function]   Black-and-white control (D&N) AUTO2
  
CP310
CP310
CP300  
[1]	+	[6]	+	[9]	+	[Camera	function]		 Iris	of	lens	(IRIS)	OPEN
[1]	+	[7]	+	[0]	+	[Camera	function]		 Iris	of	lens	(IRIS)	CLOSE
[1]	+	[7]	+	[1]	+	[Camera	function]		 Electronic	shutter	(SHUTTER)	ON
[1]	+	[7]	+	[2]	+	[Camera	function]		 Electronic	shutter	(SHUTTER)	OFF
[1]	+	[7]	+	[3]	+	[Camera	function]		 Electronic	shutter	speed,	1	step	faster
[1]	+	[7]	+	[4]	+	[Camera	function]		 Electronic	shutter	speed,	1	step	slower
[1]	+	[7]	+	[5]	+	[Camera	function]		 Gain	adjustment	(AGC)	ON
[1]	+	[7]	+	[6]	+	[Camera	function]		 Gain	adjustment	(AGC)	OFF
[1]	+	[7]	+	[7]	+	[Camera	function]		 Electronic	sensitivity	up	(SENS	UP)	FIX	ON
[1]	+	[7]	+	[8]	+	[Camera	function]		 Electronic	sensitivity	up	(SENS	UP)	FIX	OFF
[1]	+	[7]	+	[9]	+	[Camera	function]		 Electronic	sensitivity,	1	step	up	(FIX)	
[1]	+	[8]	+	[0]	+	[Camera	function]		 Electronic	sensitivity,	1	step	down	(FIX)	
[1]	+	[8]	+	[1]	+	[Camera	function]		 Electronic	sensitivity	up	(SENS	UP)	AUTO	ON
[1]	+	[8]	+	[2]	+	[Camera	function]		 Electronic	sensitivity	up	(SENS	UP)	AUTO	OFF
[1]	+	[8]	+	[3]	+	[Camera	function]		 Electronic	sensitivity,	1	step	up	(AUTO)	
[1]	+	[8]	+	[4]	+	[Camera	function]		 Electronic	sensitivity,	1	step	down	(AUTO)
[1]	+	[9]	+	[0]	+	[Camera	function]		 Time	for	switching	at	D&N	AUTO,	2	seconds	
[1]	+	[9]	+	[1]	+	[Camera	function]		 Time	for	switching	at	D&N	AUTO,	10	seconds
[1]	+	[9]	+	[2]	+	[Camera	function]		 Time	for	switching	at	D&N	AUTO,	30	seconds	
[1]	+	[9]	+	[3]	+	[Camera	function]		 Time	for	switching	at	D&N	AUTO,	60	seconds	
[2]	+	[0]	+	[1]	+	[Camera	function]		 Image	stabilizer	(STABILIZER)	ON	
[2]	+	[0]	+	[2]	+	[Camera	function]		 Image	stabilizer	(STABILIZER)	OFF
[2]	+	[1]	+	[3]	+	[Camera	function]		 Scene	file	1
[2]	+	[1]	+	[4]	+	[Camera	function]		 Scene	file	2
[2]	+	[1]	+	[5]	+	[Camera	function]	 Gain	(AGC),	1	step	up	
[2]	+	[1]	+	[6]	+	[Camera	function]	 Gain	(AGC),	1	step	down
 
CP310
CP310
CP300  
						

							Panasonic	System	Communications	Company	of	North	America,
Unit of Panasonic Corporation of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A.
Panasonic Canada Inc. 
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada 
(905)624-5010
www.panasonic.ca
© Panasonic System Networks Co., Ltd. 2012
 sC0512-0    PGQP1295ZA    Printed in China