Panasonic Color CCTV Camera Wv Cf344 Wv Cf354 Wv Cf374 Installation Guide

11
Locally procure the screws
Screws are not supplied with this product. 
Prepare the screws according to the material, 
structure, strength and other factors of the 
mounting area and the total weight of objects 
to be mounted.
Screw tightening
 •  The screws and bolts must be tightened 
with an appropriate tightening torque 
according to the material and strength of 
the installation area. 
  •  Do not use an impact driver. Failure to 
observe this may cause overtightening and 
consequently damage to...

12
Major operating controls and their functions
(This illustration represents WV-CF344E.)
1  Video output connector
Transmits composite video signals. 
2  Mark
This mark is used when the dome cover is 
installed.
3  Lens
4 
Focus knob (with lock function) CF374  CF344 
Locks the focus position after focus 
adjustment.
5  Zoom knob (with lock function)
Locks the zoom position after zoom 
adjustment.
6  Tilting lock screw 
Fixes the tilting position. 
7  AF button [AF] 
CF354 
 page 21.
8  Setup button...

13
When installing the camera on a wall or ceiling, there are three methods as specified below.
 •  Use the one-gang junction box
  •  Installing the camera directly on a wall or ceiling
  •  Using the optional ceiling mount bracket WV-Q174E (for embedded installation on a ceiling)
Important:
 •  Procure 2 screws (M4) to secure the camera to a wall or ceiling according to the material of the 
installation area. Do not use wood screws and nails. For mounting a camera on a concrete wall 
or ceiling, use an...

14
 About the side cable access hole 
If you choose not to drill hole in the wall or 
ceiling, but to wire the camera with the cable 
exposed, cut the cable access hole on the side 
of the dome cover to provide a cable entry. 
Precautions when wiring from the side: 
•  Remove the dust guard cap. Run the cable 
through the cable access hole and bend it 
inward, then reinstall the dust guard cap. 
•  Move the cable to one side as shown. 
•  Be careful not to pinch the cable with the 
dome cover.
...

15
Installing the camera directly on a wall or ceiling
Affix the installation template label (accessory) to the ceiling or wall\
, and use a pen to mark the 
positions of the screws and cable mounting hole in the ceiling or wall. 
Remove the installation template label, and attach the camera with 2 screws (M4, locally procured). 
 Connections
Connect the video output
Important: 
 •  Be sure to turn off the power of each 
device before connecting. 
  •  Be sure to secure the coaxial cable 
connectors....

16
Important:  •  The power supply of 24 V AC/12 V DC shall be insulated against 220 to 240 V AC.
  •  The power supply is automatically switchover either 24 V AC or 12 V DC. No setting is required 
with this camera. 
Connection of power cord
When connecting the power cord, use connectors that are designed for the power cord, and be 
careful not to let the power cord fall off. 
In addition, waterproofing work is needed at the joint, e.g., wrapping waterproof tape around the 
joint. 
Cable length and wire...

17
Installation of camera 
Turn off the power of all related devices before installation. 
1  Remove the dome cover.
2 Connect all cables.
    If necessary, bind the cable with cable tie (locally procured). 
3 Install the camera (The illustration below shows installation using a \
gang junction box (locally  procured) ).
    Mount the camera with 2 screws (M4, locally procured). 
Important: 
• Be sure to avoid twisting the cables when tightening the screws.
Note:
•  When attached to the ceiling:
Install...

18
1 Connect the ∅3.5 mm miniature plug (mono channel) to the adjustment monitor output jack. 
Important:
 
•  This video output is intended for confirmation of view angle, etc. during installation or repair 
service, and not for recording or monitoring. 
Note: 
•  Video cannot be output through the video output cable after connecting the adjustment 
monitor. 
2 Pan, tilt and azimuth adjustment 
Important: 
•  When adjusting pan, tilt or azimuth, do not hold the lens of the camera.\
1	 Adjustment of...

19
3 Adjustment of azimuth 
  Adjust the azimuth by rotating the azimuth adjuster. (adjustable range: ±100 °) 
Note:  
• 
Adjust azimuth so that the image top mark is facing “∆” to display the image properly rather 
than upside-down.
Image top mark TOP mark 
azimuth adjuster
Rotation 
angle: +100 º 
Rotation 
angle: -100 º
Image top mark 

20
3 Zoom and focus adjustment 
Perform the zoom and focus adjustments at the same time as pan and tilt \
adjustments (Step 2). 
Note: 
•   
If the camera is used in near-horizontal position, the shadow of the dome cover may appear in 
the image. 
1  Loosen the zoom knob and focus knob. Select photographic subject and cho\
ose proper view 
angle through zooming. Adjust the zoom and focus rings to make the image clear (\
approximate 
adjustment). 
Note:  •    The focus may not be adjusted smoothly when...