Panasonic Cf29 Service Manual

7-23
7.2.9. Setting the TP PCB
1. Fix the TP PCB using the two Screws. No1, No2
2. Connect the three Cables to the three Connectors on theTP PCB (CN800, CN801, CN803).
Note: Tighten the Screws in the numbered order (No1, No2).
Screws : DRHM0002ZA
n  Attaching the Cable Sheet, Insulation Sheet and the Sheet
1. Attach the Sheet and Insulation Sheet on the TP PCB.
2. Attach the Cable Sheet on the Touch Pad FPC.
:No1

:No2
TP PCB
to Connector
(CN800)
to Connector
(CN801)  Connector CN801
 Connector CN800...

7-24
7.2.10. Setting the HDD Main FPC
1. Fix the HDD Main FPC to the Batt HDD CN Angle usingthe two Screws and the two Screws
2. Fix the CN Spacer to the Batt HDD CN Angle using the Screw.
3. Fix the Batt HDD CN Angle using the Screw.
Screw : DFHE5092ZA
Screw : DFHE5025ZA
Screws : DRHM5104ZA
Screws : DFHE5025XA
n  Arranging the HDD Main FPC

Battery Angle  Sheet
Rib
MINI PCI 
Spacer
HDD Connector
EMP Sheet Batt HDD FPC
FPC Conduction 
Ta p e
View A
View A




Batt HDD
CN Angle
Batt HDD
CN Angle HDD...

7-25
7.2.11. Setting the Main PCB, EXT Antenna PCB, PCMCIA Unit and RTC Battery
1. Connect the Cable the Connector (CN4) on the MainPCB, and Attach the RTC Battery.
2. Fix the PCMCIA to the Main PCB using the Screws. No1 to No4
3. Connect the six Cables to the six Connectors. (Main PCB: CN6, CN9, CN10, CN51, CN54)
(EXT Antenna PCB: CN1)
4. Fix the Main PCB using the three Screws. No5 to No7
5. Fix the Main PCB using the two Screws. No8, No9
6. Fix the Main PCB using the two Screws. No10, No11
7. Fix the...

7-26
n
 Attaching the SD INS Sheet, Coil Cooling Sheet and MINI PCI Spacers
n  Setting the LAN Cable and Modem Cable
1. Set the LAN Cable and the Modem Cable to the DC/USB Cover Frame.
2. Set the Clampers to the LAN Cable and the Modem Cable.
3. Fix the DC/USB Cover Plate, the DC USB Cover Hook and the DC/USB Cover Frame using the two Screws. No1, No2 
Note: Tighten the Screws in the numbered order (No1, No2).
Screw : DRHM5025YA
SD INS Sheet Coil Cooling Sheet
IC
IC
MINI PCI Spacers
Ribs
DC/USB Cover...

7-27
n
 Setting the Main PCB
1. Set the Main PCB to the Top Cabinet in order.
View C
View A
View B
View C
View A
View B
Power SW Cable
Cable
Cable
Main PCB LAN Cable
LAN Cable
Clamper
Clamper
Confirm that the tying point of the 
LAN Cables Clamper is in the 
opposite direction to Main PCB.
Pass the Power SW Cable through 
the upper side of Cable.
Confirm that the Pin of the Top 
Cabinet of the hole of the Main PCB.
Pull out the LAN Cable
Confirm that the Pin of 
the Top Cabinet of the 
hole of the Main...

7-28
n
 Arranging the Cables and attaching the Sheets, the Tape, the Space PWB Hold MP and the Insulation Sheet
1. Connect the five Cables to the five Connectors.
(Main PCB: CN6, CN9, CN10, CN51, CN54)
2. Attach the three Sheets, the Tape, the Space PWB Hold MP and the Insulation Sheet.
View A
View B
View C
View D
View A
View BView CView D
0~1mm
Connect the 
Connector CN10.
Sheet
Sheet Sheet
IO FPC
Tape Insulation Sheet
Insulation Sheet Space PWB 
Hold MP
Ta p e
Space PWB 
Hold MP
IC
Connect the...

7-29
n
 Setting the RTC Battery
1. Connect the Cable to the Connector CN4 on the Main PCB.
2. Attach the RTC Battery to the Main PCB.
Connect the Connector CN4.
RTC Battery
Gasket
Main PCB
0~1mm 0~1mm
1~2mm
1~2mm
1~2mm
Safety Working 

7-30
7.2.12. Setting the PAD SW FFC Cover
1. Set the Power Cable Guard. 
2. Fix the PAD SW FFC Cover using the three Screws.No1 to No3
Note: Tighten the Screws in the numbered order (No1 to No3).
Screws : DFHE5054XA
n  Arranging the Power SW Cable
:No1

:No2

:No3
PAD SW FFC
Cover
Power Cable 
Guard
Power Cable 
Guard
Main PCB
Power SW Cable 

7-31
7.2.13. Setting the Wireless Module and SD PCB
1. Attach the Memory Heat Plate to the Main PCB.
2. Set the Wireless Module to the Main PCB.
3.
Attach the MINI PCI Protector Sheet to the
Wireless Module.
4. Connect the Cable to the Connector (CN2) on the EXTAntenna PCB. 
5. Attach the CD Edge Sheet and the two MINI PCI Spacers U2.
6. Fix the SD PCB using the three Screws. No1 to No3
7. Connect the Cable to the Connector on the Main PCB.
8.
Attach the two Heat Dissipation Rubbers to the Main PCB....

7-32
n
 Attaching the Memory Heat Plate
7.2.14. Setting the Speaker
1. Set the MP Eject Slide Ass’y to the Bottom Cover.
2. Fix the MP Eject BOUSUI Plate using the Screw.
3. Fix the MP Eject Lever using the four Screws.
4. Fix the Heat Pipe Unit Bottom using the two Screws.
5. Fix the three Speaker Angles to the Speaker using the
three Adhesive Tapes.
6. Attach the Speaker Spacer to the Speaker.
7. Attach the CPU Heatsink Rubber and the LAN Heat Plate Spacer to the LAN Heat Plate.
8. Fix the Speaker and...