Panasonic Cf29 Service Manual
Have a look at the manual Panasonic Cf29 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![](/img/blank.gif)
7-23 7.2.9. Setting the TP PCB 1. Fix the TP PCB using the two Screws. No1, No2 2. Connect the three Cables to the three Connectors on theTP PCB (CN800, CN801, CN803). Note: Tighten the Screws in the numbered order (No1, No2). Screws : DRHM0002ZA n Attaching the Cable Sheet, Insulation Sheet and the Sheet 1. Attach the Sheet and Insulation Sheet on the TP PCB. 2. Attach the Cable Sheet on the Touch Pad FPC. :No1 :No2 TP PCB to Connector (CN800) to Connector (CN801) Connector CN801 Connector CN800 Connector CN803 to Connector (CN803) Insulation Sheet Sheet Top Cabinet Touch Pad FPC Cable Sheet TP PCB LED FFC Sheet LED FFC Rib of the Top Cabinet Top Cabinet TP PCB ConnectorsView A View A 0~0.5mm 1~2mm 0~2mm 0~1mm 0~1mm 0~1mm
![](/img/blank.gif)
7-24 7.2.10. Setting the HDD Main FPC 1. Fix the HDD Main FPC to the Batt HDD CN Angle usingthe two Screws and the two Screws 2. Fix the CN Spacer to the Batt HDD CN Angle using the Screw. 3. Fix the Batt HDD CN Angle using the Screw. Screw : DFHE5092ZA Screw : DFHE5025ZA Screws : DRHM5104ZA Screws : DFHE5025XA n Arranging the HDD Main FPC Battery Angle Sheet Rib MINI PCI Spacer HDD Connector EMP Sheet Batt HDD FPC FPC Conduction Ta p e View A View A Batt HDD CN Angle Batt HDD CN Angle HDD Main FPC CN Spacer Battery Connector Insulation Sheet Press Set the Batt HDD CN Angle sliding to the left so that the HDD Main FPC does not attach to the Rib of the Top Cabinet. HDD Main FPC HDD Main FPC HD FPC Tape Cable Sheet Cable Sheet Sheet Sheet White line White line White line White line White line 0~2mm 2~3mm R0.5~1.0mm 1±1mm 1±1mm 0~1mm 0±0.5mm Bend 90 Bend 180Bend 180 Bend 180 Bend 90 Component sideFoil side Attention when bending the FPC 1. Inside of bending should be from R0.5mm to R1mm. 2. Do not mistake the direction of bending.
![](/img/blank.gif)
7-25 7.2.11. Setting the Main PCB, EXT Antenna PCB, PCMCIA Unit and RTC Battery 1. Connect the Cable the Connector (CN4) on the MainPCB, and Attach the RTC Battery. 2. Fix the PCMCIA to the Main PCB using the Screws. No1 to No4 3. Connect the six Cables to the six Connectors. (Main PCB: CN6, CN9, CN10, CN51, CN54) (EXT Antenna PCB: CN1) 4. Fix the Main PCB using the three Screws. No5 to No7 5. Fix the Main PCB using the two Screws. No8, No9 6. Fix the Main PCB using the two Screws. No10, No11 7. Fix the Main PCB using the Screw. No12 8. Fix the Main PCB using the two Screw. No13, No14 9. Fix the EXT Antenna PCB using the two Screws. No15, No16 Note: Tighten the Screws in the numbered order (No1 to No16). Screws : DFHM5054XA Screws :DFHE5025XA Screws :DFHE5025XA Screws : DRQT2+G6FKL Screws : DRHM5104ZA Screw : DFHE5025ZA Screw : DRHM5117ZA :No10 :No11 :No1 :No2 :No3 :No4 :No12 :No8 :No9 EXT Antenna PCB Connector CN1 to Connector (CN4) RTC Battery Connector CN10 (front side) Connector CN51 (front side) Connector CN6 (reverse side) Connector CN9 (reverse side) Connector CN1 (reverse side) PCMCIA Unit to Connector (CN6)to Connector to Connector (CN9) to Connector (CN950) to Connector (CN51) to Connector (CN54) to Connector (CN10) Connector CN4 (reverse side) Connector CN54 (reverse side) Main PCB :No13 :No14 :No16 :No15 :No5 :No7 :No6 (EXT Antenna CN1) to Connector (Main PCB CN1)
![](/img/blank.gif)
7-26 n Attaching the SD INS Sheet, Coil Cooling Sheet and MINI PCI Spacers n Setting the LAN Cable and Modem Cable 1. Set the LAN Cable and the Modem Cable to the DC/USB Cover Frame. 2. Set the Clampers to the LAN Cable and the Modem Cable. 3. Fix the DC/USB Cover Plate, the DC USB Cover Hook and the DC/USB Cover Frame using the two Screws. No1, No2 Note: Tighten the Screws in the numbered order (No1, No2). Screw : DRHM5025YA SD INS Sheet Coil Cooling Sheet IC IC MINI PCI Spacers Ribs DC/USB Cover Plate DC/USB Cover Frame DC/USB Cover Frame Modem Cable LAN Cable Clampers DC USB Cover Hook :No1 :No2 Rib The LAN Cable should be tied by the Clamper in its bottom. Do not put up the DC/USB Cover Plate on the Rib of the Top Cabinet. Safety Working Safety Working
![](/img/blank.gif)
7-27 n Setting the Main PCB 1. Set the Main PCB to the Top Cabinet in order. View C View A View B View C View A View B Power SW Cable Cable Cable Main PCB LAN Cable LAN Cable Clamper Clamper Confirm that the tying point of the LAN Cables Clamper is in the opposite direction to Main PCB. Pass the Power SW Cable through the upper side of Cable. Confirm that the Pin of the Top Cabinet of the hole of the Main PCB. Pull out the LAN Cable Confirm that the Pin of the Top Cabinet of the hole of the Main PCB. Confirm that the Boss of the Top Cabinet of the hole of the Batt HDD CN Angle. Pass the LAN Cable through this Slot. SlotTying point Main PCB MP CN Spacer Hole Tip of the Screw Tip of the Screw Hole Slot Batt HDD CN Angle 1 2 Safety Working Safety Working Safety Working
![](/img/blank.gif)
7-28 n Arranging the Cables and attaching the Sheets, the Tape, the Space PWB Hold MP and the Insulation Sheet 1. Connect the five Cables to the five Connectors. (Main PCB: CN6, CN9, CN10, CN51, CN54) 2. Attach the three Sheets, the Tape, the Space PWB Hold MP and the Insulation Sheet. View A View B View C View D View A View BView CView D 0~1mm Connect the Connector CN10. Sheet Sheet Sheet IO FPC Tape Insulation Sheet Insulation Sheet Space PWB Hold MP Ta p e Space PWB Hold MP IC Connect the Connector CN54. Connect the Connector CN51. Sheet SheetCable Cable Connector CN51 Cable Wireless Module Holder 0~1mm 0~1mm 1~2mm 0~1mm 3~4mm Power SW Cable CON SpacerTP PCB 0.5~1.5mm0~0.5mm 1~2mm0~1mm Do not put up the Cable on the Wireless Module Holder. Attach the Sheet in condition that the IO FPC is slid to the side of the Connector CN10. Pass the Cable through the right side of the Connector not to put up it on the Connector. Safety Working Connect the Connector CN6.Connect the Connector CN9.
![](/img/blank.gif)
7-29 n Setting the RTC Battery 1. Connect the Cable to the Connector CN4 on the Main PCB. 2. Attach the RTC Battery to the Main PCB. Connect the Connector CN4. RTC Battery Gasket Main PCB 0~1mm 0~1mm 1~2mm 1~2mm 1~2mm Safety Working
![](/img/blank.gif)
7-30 7.2.12. Setting the PAD SW FFC Cover 1. Set the Power Cable Guard. 2. Fix the PAD SW FFC Cover using the three Screws.No1 to No3 Note: Tighten the Screws in the numbered order (No1 to No3). Screws : DFHE5054XA n Arranging the Power SW Cable :No1 :No2 :No3 PAD SW FFC Cover Power Cable Guard Power Cable Guard Main PCB Power SW Cable
![](/img/blank.gif)
7-31 7.2.13. Setting the Wireless Module and SD PCB 1. Attach the Memory Heat Plate to the Main PCB. 2. Set the Wireless Module to the Main PCB. 3. Attach the MINI PCI Protector Sheet to the Wireless Module. 4. Connect the Cable to the Connector (CN2) on the EXTAntenna PCB. 5. Attach the CD Edge Sheet and the two MINI PCI Spacers U2. 6. Fix the SD PCB using the three Screws. No1 to No3 7. Connect the Cable to the Connector on the Main PCB. 8. Attach the two Heat Dissipation Rubbers to the Main PCB. Note: Tighten the Screws in the numbered order (No1 to No3). Screws : DFHE5025XA n Attach the MINI PCI Protector Sheet, the CD Edge Sheet, the MINI PCI Spacers U2 and the Heat Dissipation Rubbers Main PCB Connector CN2 EXT Antenna PCB Connector SD PCB :No1 :No2 :No3 to Connector (CN2) to Connector (CN952) Wireless Module Memory Heat Plate Heat Dissipation Rubbers MINI PCI Protector Sheet MINI PCI Spacer U2 MINI PCI Spacer U2 CD Edge Sheet Confirm that the Insulation Sheet is attached between the SD PCB and the Main PCB. Safety Working View B View D View E View C View A View C View A View BView D View E 0~0.5mm0~1mm 0~0.5mm 0~1mm 2~3mm 0~0.5mm 0~0.5mm 4±1mm 1.5~5.5mm Wireless Module Heat Dissipation Rubber Heat Dissipation Rubber Heat Dissipation Rubber IC 2~3mm 0.5~2.5mm Heat Dissipation Rubber IC Main PCB MINI PCI Protector Sheet MINI PCI Protector Sheet MINI PCI Protector Sheet MINI PCI Spacer U2 MINI PCI Spacer U2 MINI PCI Spacer U2 MINI PCI Spacer U2 CD Edge Sheet CD Edge Sheet Safety WorkingSafety WorkingSafety Working
![](/img/blank.gif)
7-32 n Attaching the Memory Heat Plate 7.2.14. Setting the Speaker 1. Set the MP Eject Slide Ass’y to the Bottom Cover. 2. Fix the MP Eject BOUSUI Plate using the Screw. 3. Fix the MP Eject Lever using the four Screws. 4. Fix the Heat Pipe Unit Bottom using the two Screws. 5. Fix the three Speaker Angles to the Speaker using the three Adhesive Tapes. 6. Attach the Speaker Spacer to the Speaker. 7. Attach the CPU Heatsink Rubber and the LAN Heat Plate Spacer to the LAN Heat Plate. 8. Fix the Speaker and the LAN Heat Plate using the four Screws. 9. Attach the Radiation Rubber, Coil Cooling Sheet and the LCD Lamp Sheet to the LAN Heat Plate. Screws : DXQT26+D4NLT Screws : DXYN+J6FNL Screws : DXYN26+F5NLT Screw : DXQT26+D4NLT 0~1mm 0~1mm IC Memory Heat Plate MP Eject Lever MP Eject BOUSUI Plate MP Eject Spring LAN Heat Plate Radiation Rubber CPU Heatsink Rubber Heat Pipe Unit Bottom MP Eject Slide Ass’yDIMM Stopper Sheet Speaker Spacer Speaker Speaker Angle LAN Heat Plate Spacer Adhesive Tape Bottom Cover LCD Lamp Sheet Coil Cooling Sheet