Panasonic Cf Vdw07crfm Owners Manual

21
Inserting a battery pack
1Firmly attach the battery pack to the connector.
Be sure to insert the battery pack as illus-
trated.
Be sure to the battery pack is properly con-
nected to the connector.
2Close the cover.
3Slide the latch to the left.
CAUTION
For an improperly attached cover, your battery pack may fall out while you
are carrying around your wireless display.
Be sure the tab does not get caught when closing the cover.
Connector
Charging the Battery Pack
Connect the wireless display to a...

22
Mode :  Connect        OfflineView
Backlight : LOW MIDHIGH
Profile : Profile 1
Setting the Wireless Display
Menu Button
Press Menu button.
The setting menus are displayed.
General Menu
By selecting [General], you can change the mode setting, the backlight setting and the
profile setting. You can establish the settings for the wireless display.
General WirelessBatteryOption Version
Default settings
100%ExcellentOK Cancel
The saved screen is displayed.
(
 page 33)
Electronic wave conditions (Excel-...

23
Set the high temperature mode func-
tion to [Normal temperature] or
[High temperature].
When using the wireless display in a
high-temperature environment, be
sure to set the wireless display in the
high-temperature mode.
Battery Menu
By selecting [Battery], the battery status will be displayed.
General WirelessBatteryOption Version
100%ExcellentOKCancel
Run the refresh battery.
When the confirmation message is
displayed, select [Yes].
Once the battery indicator turns green,
the battery pack will be...

24
Setting the Wireless Display
Option Menu
By selecting [Option], you can establish the individual settings for the wireless display.
General WirelessBatteryOption Version
100%ExcellentOK Cancel
Default settings
Change the password that is input to
run the wireless display.
Set the resume function to [Normal
resume] or [Quick resume], then se-
lect [OK].
Normal resume:
The wireless connection is dis-
abled during display off.
Quick resume:
Only the screen is turned off dur-
ing display off. If there is...

25
Version Menu
By selecting [Version], the version information will be displayed.
General WirelessBatteryOption Version
Model No. : CF-VDW07CRFM
Firmware : Vx.xxLxx
Wireless Controller : xx. xx. xx. xx
Serial No. :xxxxxxxx
100%ExcellentOK Cancel
(This screen is a sample.)
“x” will change depending on the configuration of the wireless display. 

26You can set the wireless display properties as follows.
1Select [Wireless Display Setup Utility] in the following
procedure.
[start] - [All Programs] - [Panasonic]
2Enter the Supervisor Password.
The Supervisor Password is not set at the time of the pur-
chase.
Press the Menu button, select [Option], then set the Su-
pervisor Password.  (
 page 24)
3Set the wireless display settings, TCP/IP and WEP.
You can set them for each profile.
Wireless Display Setup Utility
Changing the Wireless Display...

27
4At the confirmation screen, select [Next].
The message “These settings will be sent to your display”
will be displayed. Select [OK].
5
[Set up your PC] screen will be displayed.
Enter the Wireless LAN and TCP/IP settings shown on
the screen to your computer, then select [Finish].

[Completed] screen will be displayed.
Select [Finish].
MeiWDS cannot be set at the same time as those of
the wireless display. (
 page 28)
NOTE   

281Select [MeiWDS Setup Utility] in the following proce-
dure.
[start] - [All Programs] - [Panasonic]
2Enter the Supervisor Password.
In the default setting, the Supervisor Password is set to
“supervisor”.
3Set the password and AES Encryption settings.
If the setting between the computer and wireless dis-
play doesn’t confirm (e.g., the display has changed to
another one.), set it again in the following procedure.
Set AES Key Length.

Select [AES Key], and set the AES Key(s) using phrase
or binary, then...

29
Use an ISO/AAMVA/CADMV-compliant magnetic
card.
Any dirt or damage to the card may cause read errors.
Clean the card as needed.
Clean the head of the card reader at least once a week
with a “cleaning card.”
Avoid using near a strong magnetic field, i.e. a CRT, or
large audio speakers, as a strong magnetic field may
cause read errors.
CAUTION
Magnetic Stripe Reader
How to Use
Before swiping the card, place the card so its edge is com-
pletely flat against the scanner bed and confirm that the card
is...

30
NOTE
How to Use
Fingerprint Scanner
To avoid possible damage to the fingerprint scanner by static electric-
ity or improper finger placement, read the following guidelines.
1Static Electricity Discharge:
Before a scan is taken, have the person whose fingerprint is to be
taken touch the closed shutter with a finger to discharge static elec-
tricity.
2When opening the shutter:
Slide the shutter open. Do not pull the shutter to open it, as the fin-
gernail may scratch the scanner.
3Optimum finger...