Panasonic Cf 73scvtsbm Owners Manual

							31
Troubleshooting
Do not interrupt the reinstallation procedure be-
fore completion, for example by turning off the
computer or pressing
Ctrl   +   Alt   +   Del  , as
this may prevent Windows from starting up, or may
cause data to be lost so that the reinstallation pro-
cedure  cannot be executed.
11Remove the Product Recovery DVD-ROM, and then press
any key.
The computer will be shut down.
12
Turn on the computer, and press   F2   while [Panasonic]
boot screen is displayed.
The Setup Utility will start up.
If the password has been set, enter the Supervisor Pass-
word.
13
Press    F9  .
At the confirmation message, select [Yes] and press
   Enter   .  (The Setup Utility settings will return to their
default values.  Even the security settings with the excep-
tion of the password(s) will return to their default values.)
14Select [Exit] and then select [Save Current Values], then
press    Enter   .
At the confirmation message, select [Yes] and press
Enter   .
15Turn off the computer by pressing the power switch. 10
At the confirmation message, press   Y   .
The operation of reinstallation for the hard disk starts au-
tomatically. (The operations take about 15 minutes.)
You can change the drive letter for the CD/DVD drive or hard
disk drive by the following steps.
Drive letters can only be changed when two or more parti-
tions have been created on the hard disk drive. The name
of the C: drive cannot be changed.
We recommend that you make these changes before in-
stalling applications.
1Select [start] - [Control Panel] - [Performance and Mainte-
nance] - [Administrative Tools] - [Computer Management].
2Select [Disk Management] from [Storage].
3Right click on the partition of the hard disk or the name of
the CD/DVD drive and select [Change Drive Letter and
Paths...].
4Select [Change].
5Select [Assign the following drive letter] and select the
new drive letter, and then select [OK].
6At the confirmation message, select [Yes].
CAUTION
After the reinstallation procedure completes, this screen
should appear.
-----------------------------------------------------------------------[Recovery] is complete.
Windows(R) XP Professional install wizard will start after reboot.
Please remove the Product Recovery DVD-ROM, and turn off the computer.
------------------------------------------------------------------------
16Perform the first-time use operation ( page 12 step 6
- page 14 step 9 ).
17Run the Setup Utility and change the settings where nec-
essary.
If additional instructions are included with the com-
puter, be sure to read them. It may be necessary to
perform additional operations during the following
procedures.
NOTE 
						

							32
Appendix
LIMITED USE LICENSE AGREEMENT
THE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC® PRODUCT (“PRODUCT”)
ARE LICENSED ONLY TO THE END-USER (“YO U”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH
THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED
TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.
Matsushita Electric Industrial Co., Ltd. (“MEI”) has developed or otherwise obtained the Programs and hereby licenses
their use to you. You assume sole responsibility for the selection of the Product (including the associated Programs) to
achieve your intended results, and for the installation, use and results obtained therefrom.
LICENSE
A. MEI hereby grants you a personal, non-transferable and non-exclusive right and license to use the Programs in
accordance with the terms and conditions stated in this Agreement. You acknowledge that you are receiving only
a LIMITED LICENSE TO USE  the Programs and related documentation and that you shall obtain no title,
ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms,
concepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of
which title, ownership and rights shall remain with MEI or its suppliers.
B. You may use the Programs only on the single Product which was accompanied by the Programs.
C. You and your employees and agents are required to protect the confidentiality of the Programs. You may not
distribute or otherwise make the Programs or related documentation available to any third party, by time-sharing
or otherwise, without the prior written consent of MEI.
D. You may not copy or reproduce, or permit to be copied or  reproduced, the Programs or related documentation
for any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support of
your use of the Programs on the single Product which was accompanied by the Programs. You shall not modify,
or attempt to modify, the Programs.
E. You may transfer the Programs and license them to another party only in connection with your transfer of the
single Product which was accompanied by the Programs to such other party. At the time of such a transfer, you
must also transfer all copies, whether in printed or machine readable form, of every Program, and the related
documentation, to the same party or destroy any such copies not so transferred.
F. You may not remove any copyright, trademark or other notice or product identification from the Programs and
you must reproduce and include any such notice or product identification on any copy of any Program.
YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE
THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.
YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN
WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.
IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO  ANOTHER PARTY, EXCEPT AS PERMIT-
TED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.
TERM
This license is effective only for so long as you own or lease the Product, unless earlier terminated. You may terminate
this license at any time by destroying, at your expense, the Programs and related documentation together with all
copies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions
therefor set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon
any such termination, you agree to destroy, at your expense, the Programs and related documentation together with all
copies thereof in any form.
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND
BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATE-
MENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT,
ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MAT-
TER OF THIS AGREEMENT.
About Intel
® software products
The enclosed software products and documentation were developed at private expense, and are provided with “RESTRICTED
RIGHTS.” Use, duplication or disclosure by the government is subject to restrictions as set forth in FAR 52.227-14 and
DFARS 252.227-7013 et. seq. or its successor. The use of this product by the government constitutes acknowledgment of
Intels proprietary rights in the product. 
						

							33
Appendix
A. MEI vous octroie par les présentes le droit et la licence personnels, non cessibles et non exclusifs dutiliser les
Logiciels conformément aux termes, clauses et conditions de ce Contrat. Vous reconnaissez ne recevoir quun
droit limité dutiliser les Logiciels et la documentation les accompagnant et vous vous engagez à nobtenir aucun
droit de titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la documentation les accompagnant ni
vis-à-vis des algorithmes, concepts, dessins, configurations et idées représentés par ou incorporés dans les
Logiciels et la documentation les accompagnant, dont les titres, propriété et droits resteront tous à MEI ou à
leurs propriétaires.
B. Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les Logiciels.
C. Vous et vos employés ou agents êtes requis de protéger la confidentialité des Logiciels. Vous ne pouvez ni
distribuer ni mettre les Logiciels et la documentation les accompagnant à la disposition dun tiers, par partage de
temps ou de quelque autre manière que ce soit, sans lautorisation écrite préalable de MEI.
D. Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels ni de la documen-
tation les accompagnant pour quelque fin que ce soit, à lexception dune (1) copie des Logiciels à des fins de
sauvegarde uniquement pour soutenir votre utilisation des Logiciels sur le Produit unique qui est accompagné
par les Logiciels. Vous ne pouvez ni modifier ni tenter de modifier les Logiciels.
E. Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre partie quen rapport avec votre cession
du Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous
devez céder également toutes les copies, que ce soit sous forme imprimée ou lisible par la machine, de tous les
Logiciels ainsi que de la documentation les accompagnant, à la même partie ou détruire les copies non cédées.
F. Vous ne pouvez retirer aucune marque de droits dauteur, marque ou autre ni aucune identification de produit
des Logiciels et vous devez reproduire et inclure toutes ces notices ou identifications de produit sur toutes les
copies des Logiciels.
Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni aucune de leurs
copies, de façon électronique ou mécanique, en tout ou en partie.
Vous ne pouvez utiliser, copier, modifier, altérer ni céder les Logiciels ni aucune de leurs copies, en tout ou en partie,
à lexception de ce qui est expressément stipulé dans ce contrat.
Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à lexception de ce qui est autorisé
au paragraphe E ci-dessus, votre licence est automatiquement résiliée.Licence
Termes, clauses et conditions
Cette licence nest effective que pour la durée de possession ou de crédit-bail du Produit, à moins dune résiliation
antérieure. Vous pouvez résilier cette licence à tout moment en détruisant, à vos frais, les Logiciels et la documentation
les accompagnant avec toutes leurs copies, sous quelque forme que ce soit. Cette licence sera également résiliée,
avec application immédiate, si les conditions de résiliation définies ailleurs dans ce contrat se sont réalisées ou si vous
ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation, vous acceptez de
détruire, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme
que ce soit.
Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de respecter ses termes,
clauses et conditions. Vous reconnaissez en outre quils sont la description complète et exclusive du contrat conclu
entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre commu-
nication entre nous, relativement à lobjet du présent contrat. Le(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic
® (le “Produit”) sont exclusivement concédés en
licence à lutilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles ci-
dessous. En utilisant les logiciels, vous vous engagez de manière définitive à respecter les termes, clauses et condi-
tions des présentes.
Matsushita Electric Industrial Co., Ltd. (“MEI”) a mis au point ou obtenu les Logiciels et vous en concède lutilisation par
les présentes. Vous assumez lentière responsabilité du choix de ce Produit (y compris des Logiciels associés) pour
obtenir les résultats escomptés, ainsi que de linstallation, de lutilisation et des résultats obtenus.
Contrat de licence d’usage limité 
						

							34
Appendix
Hard Disk Backup Function
The hard disk backup function creates a backup area (storage area) on the hard disk. This area is to back up (store) hard disk
contents or restore backed up contents to their original locations.
By backing up the data on your hard disk to a backup area, you can protect your data from loss or damage resulting from opera-
tional errors or other factors.  Also, you can back up or restore hard disk contents using this computer alone, without having to use
other media or peripheral devices.
At the time of purchase, the hard disk backup function is disabled.  If you follow the procedure below to create a backup area, the
hard disk backup function will be enabled, and you will be able to back up your data.  Note, that once the backup function has been
enabled, you will have to perform the reinstallation procedure to disable it again (
 page 30).
Disconnect or remove all peripheral devices and SD Memory Cards. Take care to disconnect the
USB floppy disk drive, as the backup area may not be created properly while these devices are
connected.
Be sure the AC adaptor is connected to the computer.
A backup area cannot be created if the hard disk is already divided into several partitions.  Return
the computer to its condition at the time of purchase (one partition only), and create the backup
area.
To divide the partition, make the selection when the backup area is created ( page 35 step 8).
If the partition configuration is changed (partitions created, size changed, etc.) after the backup
area has been created, it will no longer be possible to execute the backup function.  To change the
configuration, it is necessary to return the computer to its condition at the time of purchase, and
then create the backup area again.
The hard disk backup function will only work for the internal hard disk. This function does not
work with an external hard disk.
Backup and restore functions will not operate if the hard disk has been damaged.
Do not use the NTFS file system compression function, as this may result in insufficient capacity
of the backup area.
If the hard disk malfunctions, it will be impossible to read the data stored on it. We recommend
that you also back up important data to a location other than the hard disk (an external hard disk
or other media).
Execute a disk error check using the following procedure.
1Display the [Local Disk(C:) properties].
Select [start] - [My Computer], right-click [Local Disk(C:)], and then select [Properties].
2Select [Check Now] from [Tools].
3In [Check Disk], select [Start] without adding a check mark beside any of the items.
If a message is displayed indicating that there is an error in the disk, display [Check Disk], and
add a check mark for [Automatically fix file system errors] and [Scan for and attempt recovery
of bad sectors], select [Start], and check for disk errors again.
The hard disk backup function does not accommodate dynamic disks.  Do not convert the hard
disk to a dynamic disk. The hard disk backup function cannot back up or restore data properly if there is a problem with the hard disk when the data is
backed up or restored.  Note that if an error occurs while data is being restored, whether as a result of an unexpected malfunc-
tion, incorrect operation, or other reason, the data in the hard disk (data before restoration) may be lost.
Matsushita Electric Industrial Co., Ltd. will bear no responsibility for any damages suffered by the user (including loss of data)
as a result of the use of this function.
Before Using a Hard Disk Backup Function
Preparing
You will need the Product Recovery DVD-ROM and CD/DVD drive (included). 
						

							35
Appendix
1Turn off the computer and insert the CD/DVD drive into the multimedia pocket. ( 
“Multimedia Pocket”)
2
Turn on the computer, and press   F2   while [Panasonic] boot screen is displayed.
The Setup Utility will start up.
If a password has been set, enter the Supervisor Password.  You cannot register [Boot] menu
with a User Password.
3
Select [Boot] menu, then select [IDE MP:  xxxxxxxxxx] and press     F6     until [IDE MP:  xxxxxxxxxx]
is at the top of the [Boot] menu.
4Place the Product Recovery DVD-ROM into the CD/DVD drive.
5
Press   F10   .
At the confirmation message, select [Yes] and press   Enter   .
The computer will restart. If [Enter Password] is displayed during the following procedures, input
the Supervisor Password or the User Password.
This screen should appear.
Regarding backup area
• Requires availability of at least half of the entire hard disk.  Without sufficient space
available, the backup area cannot be created.
• When the backup area is created, the usable hard disk capacity will be reduced to less
than half.
• The backup area cannot be accessed from Windows.  For this reason, backed up data
cannot be copied to CD-R or other removable disk media.
• When the hard disk backup function is executed, data in the backup area will be
overwritten.  If newly created or edited data is backed up later, data stored previously
in the backup area will be lost.
NOTE
Create a Backup Area
The usable hard disk area [At the time of purchase]
[After the backup area is created]
The backup area
Cannot be accessed
from Windows.Can be accessed from
Windows (One partition).
When dividing the hard disk into partitions
Do not execute [1. [Recovery]] to divide the hard disk into partitions.  The hard disk backup
function cannot be enabled after the hard disk has been partitioned.  Use procedure 8 to
divide the hard disk.
CAUTION
---------------------------------------------------------------------Select a number---------------------------------------------------------------------1. [ Recovery ] Reinstall Windows.
2. [ Erase HDD ] Erase the whole data on HDD for security.
3. [ Backup ] Enable the Backup function.
0. [ Cancel ] Cancel.
---------------------------------------------------------------------
7At the confirmation message, press   Y   .
8Select how to divide the hard disk from the menu.

Select [1]. 6
Press   3    to execute [3. [Backup]]. 
						

							36
Appendix
Hard Disk Backup Function

Select [2], enter the partition size (GB), and press   Enter   .
• You can cancel this operation by pressing    0   .
• The data partition size will be the maximum settable size less the number entered above.
The maximum settable size will differ depending on models.
9
At the confirmation message, press    Y   .
The backup area is then created.
10When the message [You must reboot in order to enable the Backup function.] appears, remove
the Product Recovery DVD-ROM, and press any key to restart the computer. The computer is
restarted, then the backup process will begin.
11 When the message [[Backup] is complete] appears, press   Ctrl   +   Alt   +   Del    to restart the
computer.
12After logging on to Windows, a message will appear advising that a new device has been
installed and that the computer must be restarted to enable the settings.  Select [Yes] to restart
the computer.
The [Boot] menu in the Setup Utility is set to start up from the CD/DVD drive. Change this
setting if necessary.
The next time the backup or restore functions are executed, follow the procedure for “Back-
ing Up and Restoring Data
” ( below).
NOTE
1Turn the computer on, and press   F2   while [Panasonic] boot screen is displayed.
The Setup Utility will start up.
If a password has been set, enter the Supervisor Password or the User Password.
2
Select [Exit] menu, then select [Hard Disk Backup / Restore] and press çEnter   .
At the confirmation message, select [Yes], and press  çEnter   .
Backing Up and Restoring Data
Before executing the backup function, execute a disk error check ( page 34).
Do not interrupt the backup or restore functions before completion, for example by turning
off the power or pressing   Ctrl   +   Alt   +   Del  , as this may prevent Windows from
starting up, or may cause data to be lost so that the backup and restore functions cannot be
executed.
CAUTION
The usable hard disk area [At the time of purchase]
[After the backup area is created]
The backup area
Cannot be accessed
from Windows.
Do not press   Ctrl   +   Alt   +   Del   until the message is displayed.
CAUTION
Can be accessed from
Windows (Two partitions). 
						

							37
Appendix
To disable the hard disk backup function
Perform the reinstallation procedure. All data in the backup area and the hard disk will be
erased.
Conduct steps 1-8 for “Reinstalling Software”  (
 page 30). Select [1] or [2] to execute the
reinstallation at the screen for executing the reinstallation.
• When [1] is selected, the hard disk backup function can be disabled.
• When [2] is selected, the hard disk backup function can be disabled, but in this case, because
the hard disk has been divided into partitions, the hard disk backup function cannot be re-
enabled  (
 page 23).
• When [3] is selected, the hard disk backup function cannot be disabled.
CAUTION
When the hard disk backup function has been enabled, the backed up data will not be erased
even if a commercial data erasing utility or similar software is used to erase all data from user-
accessible area. You can use the hard disk data erase utility included in this computer (
page 38) to erase all data on the hard disk, including backed up data. Use this hard disk data
erase utility before disposing of or transferring ownership of this computer.
Occasionally, the message [#1805 cannot write image file] will be displayed, and the backup
function will be interrupted.  If this error occurs, execute the backup function again.  After
this, if the backup function is completed properly, then there is no problem in the hard disk. 3Select the operation to be executed from the menu.

1
Press ç1ççto execute [1. [Backup]].
(When dividing the hard disk into two partitions, select the backup method at next screen.)
2
At the confirmation message, press   Y   .
The backup process will begin.

1
Press ç2ççto execute [2. [Restore]].
(When data is backed up in two partitions, select the restore method at next screen.)
2
At the confirmation message, press   Y   .
The restore process will begin.
4When the message [[Backup] is complete] or [[Restore] is complete] is displayed, press
çCtrl
ç çç ç
ççòçAltççòççDel ç to restart the computer.
•  If the backup or restore process was interrupted before completion, for example if the power
was turned off, execute the process again.
•  After logging on to Windows, when a new device is installed and a message appears advising
that the computer must be restarted to enable the settings, select [Yes] to restart the computer.
The time required to complete the backup or restore process differs depending on the
data volume.
NOTE 
						

							38
Appendix
This computer is equipped with a utility for erasing hard disk data.
When disposing of or transferring ownership of this device, erase all data on the hard disk in order to prevent the theft of hard disk
data by following the steps below.
The hard disk data erase utility erases data using an “overwriting” method, but there is a possibility that due to malfunctions or
other operational errors, data may not be completely erased. There are also specialized devices that may be able to read data
that has been erased using this method. If you need to erase highly confidential data, we recommend that you contact a
company that specializes in this process. Matsushita Electric Industrial Co., Ltd. will bear no responsibility for losses or
damages suffered as a result of the use of this utility.
Hard Disk Data Erase Utility
NOTE
Be sure the AC adaptor is connected until the procedure is completed.
This utility can only be used for internal hard disk.  It cannot be used to erase data from external hard disks.
This utility cannot erase data from damaged disk.
This utility cannot erase data for specific partitions.
After executing this utility, the computer cannot be booted from the hard disk.
The backup area and the data in the backup area will be erased. You will need the Product Recovery DVD-ROM and CD/DVD drive (included).
1Turn off the computer.
2Insert the CD/DVD drive into the multimedia pocket.
(
  “Multimedia Pocket”)
3
Turn on the computer, and press   F2   while [Panasonic]
boot screen is displayed.
The Setup Utility will start up.
If the password has been set, enter the Supervisor Password.
4Select [Boot] menu, then select [IDE MP:  xxxxxxxxxx] and
press    F6    until [IDE MP:  xxxxxxxxxx] is at the top of the
[Boot] menu.
5Place the Product Recovery DVD-ROM into the CD/DVD
drive.
6
Press   F10   .
At the confirmation message, select [Yes] and press
   Enter   .
The computer will restart, and this screen should appear.
---------------------------------------------------------------------Select a number---------------------------------------------------------------------1. [ Recovery ] Reinstall Windows.
2. [ Erase HDD ] Erase the whole data on HDD for security.
3. [ Backup ] Enable the Backup function.
0. [ Cancel ] Cancel.
---------------------------------------------------------------------

When the message [The Backup function has been en-
abled. If [Recovery] or [Erase HDD] is executed, the
Backup function will be disabled, and your Backup data
will be lost.] appears, press   Y   .7
Press   2   to execute [2. [Erase HDD]].
(You can cancel this operation by pressing   0   .)

When the message [The Backup function has been en-
abled. If [Erase HDD] is executed, the Backup func-
tion will be disabled, and your Backup data will be lost.]
appears, press   Y   .
When the message [Computer must be rebooted in or-
der to execute [Erase HDD.]] appears, press   R  .
8
At the confirmation message, press   Y   .
9
When [] is displayed, press   Enter   .
10The approximate time required for erasing data will be dis-
played.
Press   Space   .
11
At the confirmation message, press   Enter   .
The operation of erasing the hard disk will start.
(If necessary, the “hard disk data erase” operation can be
cancelled after it has begun by pressing   Ctrl   +   C   .
If the operation is cancelled before being completed, a part
of the data will not be erased.)
12After the operation is complete:
Under normal conditions, the message [Hard disk data has
been deleted.] will be displayed.
If a problem occurred during the operation, an error mes-
sage will be displayed.
13Remove the Product Recovery DVD-ROM,  and then press
any key to turn off the computer.
Preparing
Procedure 
						

							39
Appendix
Model No.
CPU
Memory
Video Memory
LCD Type
Displayed Colors*3
External Display
Hard Disk Drive
Keyboard
Pointing Device
Speaker
Sound
Multimedia Pocket Device
Supports DVD
CD
Others
DVD-ROM read*10
CD-ROM read*10
CD-R write*11
CD-RW write
High-Speed
CD-RW write
Ultra-Speed
CD-RW write
PC Card Slots
Allowable current
(total for two slots)
RAM Module Slot*12
SD Memory Card Slot*13
InterfaceExternal Display Port
Serial Port
Microphone Jack*14
Headphone Jack
Expansion Bus
Connector
USB Ports
I/O Box Connector
Modem
LAN*15
Wireless LANCF-73SCVTSBM CF-73TCVTSBM CF-73SCUTSBM CF-73TCUTSBM
Intel® Pentium® M Processor 750 (1.86 GHz, 2 MB*1 L2 cache, 533 MHz FSB)
512 MB*1 (1536 MB*1 Max.) 256 MB*1 (1280 MB*1 Max.)
UMA (128 MB*1 Max.)*2
13.3 type (TFT) with Touchscreen
65,536/16,777,216 colors (800 x 600 dots/1024 x 768 dots)
65,536/16,777,216 colors (800 x 600 dots/1024 x 768 dots/1280 x 1024 dots/1600 x 1200
dots/2048 x 1536 dots)*4
80GB*560GB*5
Windows keyboard (87 keys)
Touch Pad, Touchscreen (Anti-Reflection, Stylus (included) touch capable)
Card Speaker x 2
WAVE and MIDI playback
DVD-ROM & CD-R/RW Drive
DVD-ROM (4.7 GB, 8.5 GB, 9.4 GB, 17 GB)*5, DVD-R*6 (1.4 GB, 3.95 GB, 4.7 GB)*5, DVD-RW*6*7
(1.4 GB, 4.7 GB, 9.4 GB)*5, DVD-RAM*6*8 (1.4 GB, 2.8 GB, 2.6 GB, 5.2 GB, 4.7 GB, 9.4 GB)*5
CD-Audio, CD-ROM, CD-R, Photo CD, VideoCD, Enhanced Music CD, CD-RW, CD-TEXT
+R*6 (4.7 GB*5), +RW*6 (4.7 GB*5)
8x speed (Max.)
24x speed (Max.)
4x speed, 8x speed, 10 - 16x speed, 10 - 24x speed
4x speed
4x speed, 8x speed, 10x speed
10x speed, 10-16x speed, 10-24x speed
Two Type I or Type II, or one Type III
3.3 V: 400 mA
5 V: 400 mA
200-pin, 1.8 V , SO-DIMM, DDR2 SDRAM, PC2-3200 Compliant
SD Memory Card
Mini Dsub 15-pin female
Dsub 9-pin male
Miniature jack, 3.5 DIA
Miniature jack, 3.5 DIA
Dedicated 84-pin female
4-pin x 2, USB 2.0
Dedicated 36-pin male
RJ-11  jack, Data: 56 kbps (V.92)   FAX:14.4 kbps
RJ-45  jack, IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T
Built-in  page 40 — Built-in  page 40 —
Specifications
Main Specifications
*11 MB = 1,048,576 bytes
*2A segment of the main memory is allotted automatically depending on the computer’s operating status. The size of the Video Memory
cannot be set by the user.
*
3A 16,777,216 color display is achieved by using the dithering function.
*4Maximum resolution depends on the specifications of the external display.
*51 GB = 1,000,000,000 bytes.  Your operating system or some application software will report as fewer GB.
*6Read only.
*7Does not support DVD-RW Ver. 1.0.
*8In the case of DVD-RAM, only non-cartridge discs or removable car tridge discs can be used.
*9The data transfer rate of DVD per 1x speed is 1,350 KB/s.
The data transfer rate of CD per 1x speed is 150 KB/s.
*
10If an unbalanced disc (e.g., a disc with which the balance has been displaced from the center) is inserted, the speed may become slower
if there are large vibrations while the disc is rotating.
*
11Depending on the disc, the writing speed may become slower.
*12A PC2-3200-compliant or PC2-4200-compliant RAM module can be added. A PC2-4200-compliant RAM module added to this computer,
operates at the same speed as a PC2-3200-compliant RAM module.
*
13This slot does not support the MultiMedia card.
Operation has been confirmed for Panasonic SD Memory Cards with up to 1 GB capacity.
*
14Use only a monaural condenser microphone.
*15When using the LAN port of the port replicator, IEEE802.3ab 1000Base-T is not available.
Data
transfer
rate*
9 
						

							40
Appendix
Battery Pack
Main battery
Main battery +
Second battery
Main battery
Main battery +
Second battery
Clock Battery
AC Adaptor*4Input
Output
Power Consumption*5
Operation Temperature
Humidity
StorageTemperature
Humidity
Physical Dimensions (W x H x D)
(excluding the carrying handle)
Weight (including the carrying handle)Li-ion 11.1 V, 3.8 Ah
3 hours - 4 hours*2 (Approx. 3.5 hours*3)
Approx. 6 hours - 8 hours*2
 (Approx. 7 hours*3)
Approx. 3 hours
Approx. 6 hours
Coin type lithium battery 3.0 V
100 V - 240 V AC, 50 Hz/60 Hz
15.6 V DC, 5.0 A
Approx. 35 W*6 / Approx. 80 W (maximum when recharging in the ON state)
5 °C to 35°C  {41 °F to 95 °F}
30% to 80% RH  (No condensation)
-20 °C to 60 °C  {-4 °F to 140 °F}
30% to 90% RH  (No condensation)
297 mm x 35.5 - 46 mm x 254 mm
{11.7  X 1.4 - 1.8  X 10 }
Approx. 2.6 kg {Approx. 5.7 lb.}
Main Specifications
*1Varies depending on the usage conditions ([Audio Power Management] in the Setup Utility: [Enable], etc).
*2Measured using BatteryMark™ Version 4.0.1 (LCD brightness: Maximum - Minimum)
*3Measured using MobileMark™ 2002 (LCD brightness: 60 cd/m2)
*4
The AC adaptor is compatible with power sources up to 240 V AC adaptor.  This computer is supplied with a 125 V AC compatible AC cord.
*
5Approx. 1.0 W when the battery pack is fully charged (or not being charged) and the computer is off.
Approx. 2.0 W when the Wake up from LAN function has been enabled.
*
6Rated power consumption.
 Software
Microsoft® Windows® XP Professional Service Pack 2 with Advanced Security Technologies
(NTFS File System)
Setup Utility
DMI Viewer
Adobe Reader
Intel
® PROSet/Wireless Software*7
PC Information Viewer
Hard Disk Backup Utility*8
Hard Disk Data Erase Utility*8
SD Utility
Icon Enlarger
Loupe Utility
Hotkey Settings
Battery Recalibration Utility
WinDVD™5
B’s Recorder GOLD7 BASIC
B’s CLiP 6
Operating System
Utility Programs
Operating
Time*1
Charging
Time*1
Environment
*7Only for models with wireless LAN.
*8The Product Recovery DVD-ROM is required.
Data transfer rates
Standards supported
Transmission method
Wireless channels used
RF frequency bandIEEE802.11a: 54/48/36/24/18/12/9/6 Mbps (automatically switched)
IEEE802.11b: 11/5.5/2/1 Mbps (automatically switched)
IEEE802.11g: 54/48/36/24/18/12/9/6 Mbps (automatically switched)
IEEE802.11a/IEEE802.11b/IEEE802.11g
OFDM system, DSSS system
IEEE802.11a: Channels 36 to 64, 149 to 165
IEEE802.11b/IEEE802.11g: Channels 1 to 11
IEEE802.11a: 5.18~5.32 GHz, 5.745~5.825 GHz
IEEE802.11b/IEEE802.11g: 2412~2462 MHz
Wireless LAN (only for models with wireless LAN)
Specifications