Panasonic Cf 07 Mk1 Win98 2000 Part Dfqx5265zc Owners Manual

							11
Getting Started
Handling
This computer has been designed so as to minimize shock to the hard disk drive, etc., but
no warranty is provided against such trouble.  Therefore, as a precision instrument, be
extremely careful in the handling.
Do not drop or hit your computer against solid objects.
Remove all cables before transporting your computer.
We recommend preparing a fully charged battery.
When transporting spare batteries inside a package, briefcase, etc., it is recommended
that the batteries be stored in a plastic bag.
Do not place the computer upright or allow it to tip over.  When the computer receives
extremely strong shock after falling, the hard disk or floppy disk drive, etc., may
become inoperable.
Always carry your computer with you.  Never check it in with luggage.  For use of the
computer inside an aircraft, we recommend asking the airlines regarding their policy
on this issue.
It is a good idea to make backup copies on disks and carry them with you.
Maintenance
Wipe with a soft cloth, after applying water or de-
tergent diluted with water to the soft cloth and firmly
wringing out excess water.
Do not use benzene, thinner, or rubbing alcohol.  Doing so may adversely affect
the surface, e.g., discoloration.  In addition, do not use commercially-available
household cleaners and cosmetics, as they may contain components harmful to
the surface.
Do not directly add or spray water or detergent.  If liquid enters the inside of the
computer, it may cause it to work improperly or be damaged.
CAUTION 
						

							12
Getting Started
2Write down the Product Key
Write down the number shown on the “Certificate of Authenticity” located on the
bottom of the computer in the “Customer’s Record” section on page 2 of this manual.
First-time Operation
Read the steps below to help you learn what parts are included, and to gain an understanding
of some basic computer-related operations.
1Confirm the inclusion of all parts
Make sure the parts shown in the figure have been supplied.  If any of these items
are missing or is not working properly, contact Panasonic Technical Support.
Do not use the optional wireless display (CF-VDW07) for the first-time operation.
CAUTION
Splitter Cable .......................... 1
Model No : CF-VZSU21
Battery Packs ......................... 2
USB Cable .............. 1 Product Recovery CD-ROM
Windows   98
Operating Instructions 
(This book)........ 1
Windows® Book .................................. 1
Windows 2000
Be sure to prepare the followings.
• Optional port replicator (CF-VEB071)
• Optional floppy disk drive (CF-VFDU03)
• External keyboard (PS/2 type)
• External mouse (PS/2 type)
• External display (a “wired” display with an RGB analog 15-pin interface)
NOTE 
						

							13
Getting Started
4Insert the two battery packs
CAUTION
2Slide the latch down, and then without releasing it,
open the cover as illustrated.
3Firmly attach the battery pack to the connector as
illustrated.
4Close the cover, then lock it by sliding the latch to
the left.
3Read the LIMITED USE LICENSE AGREEMENT (page 40)
Before removing the seal covering the power switch, read the LIMITED USE LI-
CENSE AGREEMENT.
Main Battery Pack SlotSecond Battery Pack Slot
1Turn over the computer, then unlock the cover by
sliding the latch to the right.
Be sure to insert the battery pack as illustrated.
Be sure the battery pack is properly connected to the connector.
For an improperly attached cover, your battery pack may fall out while you are
carrying around your computer.
Be sure the tab does not get caught when closing the cover.
1
Bottom
Latch
3
2
Battery PackTa b
4
Cover
5Open the cover of the expansion bus
connector, then connect your com-
puter to a port replicator
3
1
Expansion Bus Connector
Port Replicator
2 
						

							14
Getting Started
6Connect an external display, external keyboard and exter-
nal mouse to the port replicator 
( Operating Instruction of the Port
Replicator)
7Connect the port replicator to a power outlet
When the AC adaptor is connected to the port replicator, charging begins automati-
cally.
3
2
1
Be sure the AC adaptor is connected until completing Step 11 on page 18.
Handling the AC adaptor
Do not twist or pull the AC power cord forcefully.  Doing so may damage
the connections.
Use only the specified AC adaptor with your computer.  Using an AC adap-
tor other than the one supplied might damage the battery and/or the computer.
When the DC plug is not connected to the computer, disconnect the AC cord
from your AC wall outlet.
Problems such as sudden voltage drops may arise during periods of thunder
and lightning.  Since this could adversely affect your computer, an
uninterruptible power source (UPS) is highly recommended unless the bat-
tery pack is installed.
CAUTION
First-time Operation
AC Adaptor*To the wireless
display
(
 Page 18)
4
AC Cord*
Splitter Cable
* This comes with the wireless display.
Power Switch
Power Indicator 8Turn on your computer
Press the power switch and hold it for approximately
one second until the power indicator turns on before
releasing it.
Do not press the power switch repeatedly.
Once the computer is powered off, you must wait at least ten seconds before
powering it on again.
CAUTION 
						

							15
Getting Started
NOTE
Depending on the user settings, if there is no input from a key or an external
mouse for a certain interval of time, the power to the external display and hard
disk may be turned off.  The external display will resume operation when an
external mouse is used or a key is pressed.
The power to the external display may be turned off when an application soft-
ware is being installed.  In this case, because it is conceivable that a selection
dialog box will be shown, do not press
Space    or    Enter    to attempt to
resume from this condition as doing so may trigger a selection, but instead,
press a key unrelated to the direct triggering of a selection, like   Ctrl   .
In addition, when the computer is left alone, it automatically may enter the
standby* mode (
   “Standby/Hibernation Functions”).  The computer
will resume by pressing the power switch.
*Windows 2000: standby or hibernation
Windows 98
9Setup Windows
NOTE
Until the wireless display is connected, use the external display, external key-
board, and external mouse for operations.
NOTE
If there is a computer with the same computer name nearby, [The following
error occurred while loading protocol number 0.] may be displayed. In this
case, press [OK]. To prevent this message from appearing the next time on,
change the name for [Computer name] in [Start] - [Settings] - [Control Panel] -
[Network] - [Identification] after the completion of the Windows setup proce-
dure.
1Select settings for your region and your keyboard layout, then select [Next].
(for U.S.A.: United States 101)
2Enter your name and select [Next].
The License Agreement will be displayed. 
						

							16
Getting Started
Do not press any key or move the mouse until [Windows 2000 Professional
Setup] is displayed.
CAUTION
Windows 2000
First-time Operation
3Select settings for your region, then select [Next].
4Enter your name and organization and select [Next].
5Enter your computer name and administrator password and select [Next].
CAUTION
Remember this password! If password is forgotten, Windows 2000 cannot
be operated.
6Input the correct date, time and time zone and select [Next].
You can also complete these settings at a later time.
7At the [Networking Settings], select [Typical settings], then select [Next].
8At the [Workgroup or Computer Domain], select [No, this computer is not on a
network, or is on a network without a domain], then select [Next].
The computer will restart.
4Select [Finish].
5Input the correct date, time and time zone and select [Close]. You can also
complete these settings at a later time.If [I do not accept the agreement] is selected, the Windows setup will be
aborted.
NOTE
3After reading the agreement, select [I accept this agreement] or [I do not accept
the agreement], then select [Next].
1At the [Welcome to the Windows 2000 Setup Wizard], select [Next].
2After reading the agreement, select [I accept this agreement] or [I dont accept
this agreement], then select [Next].
NOTE
If [I don’t accept this agreement] is selected, the Windows setup will be
aborted. 
						

							17
Getting Started
9At the [Network Identification Wizard], select [Next].
10At the [Users of This Computer], select [Users must enter a user name and
password to use this computer], then select [Next].
11Select [Finish].
12Enter your administrator password and select [OK].
Label on the top sur-
face, and insert the
shutter-side headfirst.
USB Floppy
Disk Drive
CAUTION
1Connect the optional floppy disk drive to the port
replicator.
2Prepare 2HD floppy disks and make sure they are
not in the write-protected state.
3Select [Start] - [Programs] - [Panasonic] - [Create
Backup Disk].
Follow the on-screen instructions.  Place a label
identifying the contents on each disk.
Windows 2000
When [You do not need to make “Backup Disk”] is
displayed, there is no need to create a Backup Disk.
Name of created backup disk
FIRSTAID FD (When the display for creating the
UPDATE FD is shown, create the disk by following
the on-screen instructions.)
Store the disks in a safe place. They will enable you to return your computer
to close to the condition at the time of purchase should any problems occur.
When creating disks, do not run any other application program.
When creating disks and [Insufficient files to copy] is displayed, select [OK]
and then contact Panasonic Technical Support.
While the disk drive indicator is on, do not remove the disk, power down
your computer or use the standby or hibernation function (
  “Standby/
Hibernation Functions”).
Be sure to create the Backup Disk.
If a Backup Disk is not created, it will be impossible to return the computer
to its original state. In this case, contact Panasonic Technical Support.
10Create backup disks for reinstallation
NOTE
At the [Getting started with Windows 2000] :
Press [Exit] to close.
When selecting [Discover Windows], the computer may ask you to install
the Windows 2000 CD.  In such case, close the windows, and then specify
[c:\winnt\cdimage\discover], then select [OK]. 
						

							18
Getting Started
First-time Operation
11Setup the wireless display
1Slide the latch to the right, and open the cover, then
insert the battery pack in the wireless display.  Af-
ter inserting the battery pack, close the cover, then
slide the latch to the left.(
 Operating Instruction
of the wireless display)
2Connect the wireless display to a power outlet and
turn on the wireless display.

Select network type.
AdHoc Infrastructure Cancel
Be sure to insert the battery pack as illustrated.
CAUTION
Ta b
connector
Power Switch 

Press the Menu button on the wireless display, then select [Option] , and then
select [Setup].
When [Do you want to change wireless setting?] is displayed, select [Yes].
NOTE
The following screen is displayed.
Latch 
						

							19
Getting Star ted
3Select [AdHoc].

	


		

Change setting on host PC to the following
value, reboot the host PC, then select
Connect below.
Wireless LAN card
Network Type : AdHoc
SSID : cfvdw07-43411
Encryption : disable
TCP/IP
IP Address : 10.57.148.205
NetMask : 255.0.0.0
MeiWDS
Password : wdsp
Connect       Cancel
CAUTION
Do not select [Connect] until step  10  is completed.
This screen is a sample.
4Select  on the taskbar of the external display, then select [Configuration].
The following screen is displayed.

Match the settings of the computer with
the information displayed on  of the step  
3  .
This screen is a sample.
Select [802.11.AdHoc].
Do not select [AdHoc].
CAUTION

You can select only [11] for [Channel].
CAUTION
5Select [Apply Changes], then select [OK].
The wireless display will turn off automatically after 10 minutes have
elapsed.  In this case, start the procedure from step
  2  .
NOTE     
						

							20
Getting Started
First-time Operation
7Select [OK], then select [OK].
8Windows 98
Select [Yes].  The computer will restart.

Add the check mark for [Specify
an IP address], match the settings
of the computer with the informa-
tion displayed on  of the step  
3  .
This screen is a sample.
6Windows 98
Select [Start] - [Settings] - [Control Panel] - [Network] - [TCP/IP   PRISM2
IEEE 802.11 PC CARD Adapter] - [Properties] - [IP Address].
The following screen is displayed.
Windows 2000
Select [Start] - [Settings] - [Control Panel] - [Network and Dial-up Connec-
tions] -[Local Area Connection 2] -  [Properties] -[Internet Protocol (TCP/IP)] -
[Properties].
The following screen is displayed.

Add the check mark for [Use the
following IP address], match the
settings of the computer with the in-
formation displayed on  of the step  
3  .
This screen is a sample.