Panasonic Cf 07 Mk1 Win98 2000 Part Dfqx5265zc Owners Manual

31
Troubleshooting
02D0  System cache error - Cache disabled
Contact Panasonic Technical Support.
02F0: CPU ID:
CPU socket number for Multi-Processor error.
02F4:  EISA CMOS not writable
ServerBIOS2 test error:  Cannot write to EISA CMOS.
02F5:  DMA Test Failed
ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers.
02F6:  Software NMI Failed
ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt).
02F7:  Fail - Safe Timer NMI Failed
ServerBIOS2 test...

32
Troubleshooting
Dealing with Problems (Summary)
When a problem occurs, power off the wireless display, then connect the optional port
replicator (CF-VEB071), external keyboard and external display and refer to this page.  The
“Reference Manual” also contains detailed information.  If a problem appears to be related
to a software application, read the software related manual.  If you still cannot troubleshoot
the problem, contact Panasonic Technical Support.
Check the cable connection for the AC...

33
Troubleshooting
Press   F9    in the Setup Utility (  “Setup Util-
ity”).   This will restore the Setup Utility’s settings to their
default values (except the password settings).
Try removing all peripheral devices.
Windows 98
Run SCANDISK to check the hard disk.
At start-up, press    Ctrl    to operate the computer in the
Safe mode.
Windows 2000
Click [Local Disk(C:)] in [My Computer] with the right
button, select [Properties], then select [Tools] - [Check
Now].
At start-up, press    F8    to operate...

34
Troubleshooting
Dealing with Problems (Summary)
The red indicator
lights.
Repeated beeping
sound while the com-
puter is in use.
The red indicator
blinks
The orange indicator
blinks
The green indicator
blinksThe battery level is low.  Save your data and power off your
computer.
After connecting the AC adaptor or replacing the battery pack
with a fully charged one, turn your computer on.
The battery pack or recharging function may be defec-
tive.  Quickly remove the battery pack and disconnect the
AC...

35
Troubleshooting
 Application Software
After shutting down by pressing the power switch for more
than four seconds, press the power switch to power on and
open the application again.
If the program no longer works normally, go to [Start] - [Set-
tings] - [Control Panel] - [Add/Remove Programs] to delete
the program.  Then reinstall the program.
Install the software after powering off the computer and the
wireless display and then connecting the port replicator, op-
tional USB floppy disk drive,...

36
Troubleshooting
Reinstalling Software
Before Reinstallation
 Preparing
You will need the followings:
• Product Recovery CD-ROM
• Optional port replicator (CF-VEB071)
• External keyboard
• External mouse
• External display
• If it was necessary to create BACKUP DISKS (“Create backup disks for rein-
stallation” on page 17), you will need the BACKUP DISKS (e.g., FIRSTAID
FD), the USB floppy disk drive (CF-VFDU03).
The operation of reinstallation takes about 1 hour (Windows 98) or 20 minutes
(Windows...

37
Troubleshooting
In such cases, the initial partition size must be 2 GB or more of the hard
disk size.  Reinstallation cannot be performed with a small partition size.
If [The program has detected an error 110 on the partition starting at sector
xxxxxxxx on disk1.] is displayed, select [Yes].
NOTE
8Make a selection from the menu.
To restore all contents of the hard disk to factory default, including the partition
setting(s):
Select [1. Restore the whole HDD to factory default].
Windows 98
To restore...

38
Troubleshooting
Reinstalling Software
9At the confirmation message , press   Y   .
The computer will reboot, and the operation of reinstallation for the hard disk starts
automatically.
Windows 2000
When [Insert media 2] is displayed, insert Product Recovery CD-ROM 2 into the
CD-ROM drive and immediately select [OK].
10After the reinstallation procedure completes, the following message will appear on
the display.  Remove the Product Recovery CD-ROM* and FIRSTAID FD, then re-
start the computer by...

39
Troubleshooting
11When the message [Press  to enter SETUP] is displayed, press    F2    and then
run the Setup Utility.
If the password has been set, enter the Supervisor Password.
12
Press    F9  .
At the confirmation message, select [Yes] and press   Enter   .  (The Setup Utility
settings will return to their default values.  Even the security settings with the excep-
tion of the password(s) will return to their default values.)
Change the settings where necessary.
13
Press    F10   .
At the...

40
Appendix
LIMITED USE LICENSE AGREEMENT
A. MEI hereby grants you a personal, non-transferable and non-exclusive right
and license to use the Programs in accordance with the terms and conditions
stated in this Agreement. You acknowledge that you are receiving only a LIM-
ITED LICENSE TO USE  the Programs and related documentation and that
you shall obtain no title, ownership nor any other rights in or to the Programs
and related documentation nor in or to the algorithms, concepts, designs and
ideas...