Panasonic Bluray Disc Home Theater Sound System Sc Bt230 Operating Instructions

							Getting started 
11
VQT2M13
ASpeaker cable sticker (included)
BConnector
Be sure to match the number on each sticker with the 
connector color.
	≥Be careful not to cross (short-circuit) or reverse the polarity of the 
speaker wires as doing so may damage the speakers.
≥Don’t use a front speaker as a surround speaker or vice versa. Verify 
the type of speaker with the label on the rear of the speaker before 
connecting the appropriate cable.
≥To avoid injury by falling or dropping the speaker, place the speaker cables 
with care not to stumble or hook.
≥Do not hold the speaker in one hand to avoid injury by dropping the 
speaker when carrying.
[BT330] [BT235]
[BT730] [BT330] [BT235]
∫Preventing the speakers from falling
≥Consult a qualified housing contractor concerning the appropriate procedure when attaching to a concrete wall or a surface that 
may not have strong enough support. Improper attachment may result in damage to the wall or speakers.
≥Use a string of less than ‰ 2.0 mm (
3/32q), which is capable of supporting over 10 kg (22 lbs).
e.g., [BT730]
AString (not included)
Thread from the wall to the speaker and tie tightly.
BRear of the speaker
CScrew eye (not included)
DWall
EApprox.150 mm (5 
29/32q)
Speaker cable stickerColor
1FRONT (L) WHITE
2FRONT (R) RED
3SURROUND (L) BLUE
4SURROUND (R) GRAY
5CENTER GREEN
6SUBWOOFER PURPLE
FRONT
Lch


3

Use of the speaker cable stickers is 
convenient when making cable connections.
e.g. Front speaker (L)4
Push! Connecting the speaker cables. Insert the wire fully, 
taking care not to insert beyond the wire insulation.
r: White
s: Blue line e.g. Surround speaker
Speaker assembly option
Thread the speaker cable 
through the base.Attach the speaker.
Leave about 120 mm (4 
23/32q)
You can remove and use the cable 
from the stand. To reattach the 
cable, refer to page 40.Insert the wire fully.
r: White
s: Blue line
Push!
Press into the groove.
Tighten securely.
Slide into the 
groove.

 

SC-BT230_330_730P_PC_VQT2M13_eng.book  11 ページ  ２０１０年３月１６日　火曜日　午後５時５７分 
						

							12
VQT2M13
STEP 2 : Positioning
How you set up your speakers can affect the bass and the sound field.
Setup example
Place the front, center and surround speakers at 
approximately the same distance from the seating position.
The angles in the diagram are approximate.
[BT730] [BT330]
Using “Auto Speaker Setup” (>19) is a convenient way to get 
the ideal surround sound from your speakers when you are 
unable to place them.
	≥Keep your speakers at least 10 mm (13/32z) away from the system for 
proper ventilation.
ACenter speaker
Put on a rack or shelf. Vibration caused by the speaker can 
disrupt the picture if it is placed directly on the TV.
BFront speakers
CSubwoofer
DSurround speakers
≥Place the speakers at the same height or higher than ear 
level.
E[BT730] Wireless system
≥Place the wireless system within approximately 10 m (33 
ft.) from the main unit, and in a horizontal position with 
the top panel faced upward.
≥To allow for proper ventilation and to maintain good 
airflow around the wireless system, position it with at 
least 5 cm (2z) of space on all sides.
≥Do not use the wireless system or the digital transmitter 
in a metal cabinet or bookshelf.
	≥Use only supplied speakers
Using other speakers can damage the unit, and sound quality will be 
negatively affected.
≥You can damage your speakers and shorten their useful life if you play 
sound at high levels over extended periods.
≥Positioning speakers in front
It is possible to locate all the speakers in front of the listening position. 
However, the optimal surround sound effect may not be obtainable.
≥Place speakers on flat secure bases.
≥Placing speakers too close to floors, walls, and corners can result in 
excessive bass. Cover walls and windows with thick curtains.
≥For optional wall mount, refer to page 40.
∫If irregular coloring occurs on your TV, turn 
the TV off for about 30 minutes.
If it persists, move the speakers further away from the TV.
[BT730]
∫Wireless system
To avoid interference, maintain the following distances 
between the wireless system and other electronic devices 
that use the same radio frequency (2.4 GHz band).
The wireless system will automatically seek a clear channel if 
any of these other devices interfere with its communication. 
When this happens, the wireless link indicator (“ [W] ”) flashes 
on the main unit, and there is a brief interruption in audio 
coming from the surround speakers.
This is the normal operation of the product working to assure 
the best possible performance of your home theater system.
If the interference persists, try moving the other devices to 
another location outside the range of the wireless system or 
move the wireless system nearer to the main unit.
[BT730] [BT330] [BT230] 
∫Upgrade your system to 7.1-channel 
system
The main unit is designed to enjoy the 7.1ch surround sound. By 
connecting 2 units of the Panasonic wireless system SH-FX71 
with 4 speakers, more theater-like effect can be available.
Necessary equipment:
[BT730]
≥1 optional wireless system (SH-FX71)
≥2 additional speakers 
[Impedance: 3 ≠ to 6 ≠, Speaker input power: 100 W (Min)]
[BT330] [BT230]
≥2 optional wireless systems (SH-FX71)
≥2 additional speakers
[Impedance: 3 ≠ to 6 ≠, Speaker input power: 100 W (Min)]
For more details, refer to the operating instructions for the 
optional wireless system.
Caution
≥The main unit and supplied speakers are to be used only as indicated in this setup. Failure to do so may 
lead to damage to the amplifier and/or the speakers, and may result in the risk of fire. Consult a qualified 
service person if damage has occurred or if you experience a sudden change in performance.
≥Do not attempt to attach these speakers to walls using methods other than those described in this 
manual.
≥Do not touch the front netted area of the speakers. Hold by the sides.
[BT330] [BT230]You can enjoy surround speaker sound 
wirelessly when you use the optional 
Panasonic wireless accessory 
(SH-FX71).
For more details, refer to the operating 
instructions for the optional wireless system.
120°60°







Wireless 
systemWireless LAN:
approx. 2 m (61/2 ft.)
Cordless phone and 
other electronic devices:
approx. 2 m (6
1/2 ft.)
SC-BT230_330_730P_PC_VQT2M13_eng.book  12 ページ  ２０１０年３月１６日　火曜日　午後５時５７分 
						

							Getting started 
13
VQT2M13
STEP 3: Connections
Turn off all equipment before connection and read the appropriate operating instructions.
Do not connect the AC power supply cord until all other connections are complete.
Connect to the terminals of the same color.
[BT730]
[BT330] [BT230] [BT235]
Speaker cable connection
- +
52
13 6 6FRONTCENTER SUBWOOFERRL
+
6
LS / RB LB / RS
SPEAKERS
ENCEINTES
SURROUND \(3 - 6    \)   
AMBIOPHONIQUES
SURR
L
SIDER
SIDE
  
 
Main unit
Surround selector
The surround selector 
switch must be set in 
the center position. 6PURPLE Subwoofer
5GREENCenter speaker
2REDFront speaker (Rch) 
1WHITEFront speaker (Lch)
Wireless system 3BLUESurround speaker (Lch)
4GRAYSurround speaker (Rch)
AC IN
52
13 6 6FRONTCENTER SUBWOOFERRL4
33SURROUNDRL
+
6

 

Main unit 6PURPLE Subwoofer
5GREENCenter speaker
2REDFront speaker (Rch) 
1WHITEFront speaker (Lch)
4GRAYSurround speaker (Rch)
3BLUESurround speaker (Lch)
[BT330] [BT230]
When using the optional wireless 
system, do not attempt to connect 
any extra surround or surround 
back speakers to the main unit.
SC-BT230_330_730P_PC_VQT2M13_eng.book  13 ページ  ２０１０年３月１６日　火曜日　午後５時５７分 
						

							14
VQT2M13
The basic connection is shown in the included Easy Setting Guide, however, there are more connection examples to optimize 
your system setting.
	≥Do not make the video connections through the VCR.
Due to copy guard protection, the picture may not be displayed properly.
≥Turn off all equipment before connection.
∫OPTICAL IN
≥After making the digital audio connection, make settings to 
suit the type of audio from your digital equipment (>30).
∫HDMI
The HDMI connection supports VIERA Link “HDAVI Control” 
(>31) when used with a compatible Panasonic TV. 
≥Please use High Speed HDMI Cables that have the HDMI 
logo (as shown on the cover). It is recommended that you 
use Panasonic’s HDMI cable. When outputting 1080p signal, 
please use HDMI cables 5.0 meters (16.4 ft.) or less.
Recommended part number:
RP-CDHS15 (1.5 m/4.9 ft.), RP-CDHS30 (3.0 m/9.8 ft.), 
RP-CDHS50 (5.0 m/16.4 ft.), etc.
	≥To enjoy TV audio from this home theater system’s speakers, select “AUX (TV)” as a source (>23).
	
≥To enjoy TV audio from this home theater system’s speakers, select “DIGITAL IN 1 (TV)” or “D-IN 1” as a source. 
Connection to a TV
Basic connection
AV
OUT
VIDEO
OUTAUX
1L
R
VIDEO
OUT
L
R
AUX
L
VIDEO IN
R  AUDIO IN
LR 
AUDIO OUT
VIDEO OUT
AUX


TV
AVideo cable (included)
BAudio cable (not included)
Connection for the better audio
VIDEO
OUTAUX
1L
RL
R2OPTICAL1
DIGITAL AUDIO IN
VIDEO
OUT
OPTICAL
OUT
L
VIDEO IN
R  AUDIO IN
OPTICAL 1
VIDEO OUT

TV
AVideo cable (included)
BOptical digital audio cable (not included)
SC-BT230_330_730P_PC_VQT2M13_eng.book  14 ページ  ２０１０年３月１６日　火曜日　午後５時５７分 
						

							Getting started 
15
VQT2M13
	
≥To enjoy TV audio from this home theater system’s speakers, select “DIGITAL IN 1 (TV)” or “D-IN 1” as a source (>23).
ARC (Audio Return Channel)
(Available when using an ARC compatible TV)
With this function it is possible to receive the digital audio signal from the TV without connecting any other audio cables.
≥Select “ARC (TV)” as the audio input source (>23).
≥Refer to the operating instructions of the TV for the settings to output digital audio.
	≥To enjoy TV audio from this home theater system’s speakers, select “DIGITAL IN 2 (CABLE/SAT)” or “D-IN 2” as a source 
(>23).
NECESSARY SETTINGS
≥“HDMI Audio Output” : “Off” (>37)
Connection for the best picture and audio
AV
OUT
VIDEO
OUTAUX
OPTICAL2 1
DIGITAL AUDIO  IN
L
RAV
OUTOPTICAL2 1
DIGITAL AUDIO  IN
L
R
\(ARC\)
2OPTICAL1
DIGITAL AUDIO IN
OPTICAL
OUTAV IN
OPTICAL 1
HDMI AV OUT (ARC)

TV
AHDMI cable (not included)
BOptical digital audio cable
 (not included)
≥For the TV audio, an audio cable (not included) can 
be also used by connecting the AUX terminal with 
the AUDIO OUT terminal on the TV.
Connection with Set Top Box, etc.
LANAUXLANWIRELESSRÉSEAU LOCAL
DIGITAL TRANSMITTERL
RL
R2OPTICAL1
DIGITAL AUDIO IN
OPTICAL
OUT
OPTICAL 2

TV
AOptical digital audio cable
 (not included)
BSet Top Box, cable TV, VCR, DVD recorder, etc. Refer to the operating instructions of the respective 
devices for the optimal connections.
SC-BT230_330_730P_PC_VQT2M13_eng.book  15 ページ  ２０１０年３月１６日　火曜日　午後５時５７分 
						

							16
VQT2M13
Use outdoor antenna if FM radio reception is poor.
Radio antenna connection
Using an indoor antenna
FM ANT
\(75   \)
 Main unit
AFM indoor antenna (included)
BAdhesive tape
Affix this end of the antenna where reception is 
best.
Using an outdoor antenna
FM ANT



\(75   \)
AFM outdoor antenna [Using a TV antenna
(not included)]
The antenna should be installed by a competent 
technician.
B75 ≠ coaxial cable (not included)
CAntenna plug (not included) Main unit e.g.,
[BT730] Digital transmitter connection
DIGITAL TRANSMITTER
I
Do not insert or remove while the 
home theater unit is on.
SC-BT230_330_730P_PC_VQT2M13_eng.book  16 ページ  ２０１０年３月１６日　火曜日　午後５時５７分 
						

							Getting started 
17
VQT2M13
The following services can be used when this unit is connected 
to broadband.
≥Firmware can be updated (>21)
≥You can enjoy the BD-Live (>27)
≥You can enjoy VIERA CAST (>34)For details about connection method, refer to the instructions 
supplied with the connected equipment.
≥It may not work properly depending on the equipment or 
environment used.
Connection to a broadband network
∫Using LAN (ethernet) cable
[BT730] [BT330] [BT230]
∫Using Wireless LAN Adaptor (optional)
ALAN Cable (not included)
BBroadband router, etc.
CLAN Cable (not included)
DModem (Broadband) *Provided by ISPAWireless LAN Adaptor
BWireless router (Access point), etc.
CLAN Cable (not included)
DModem (Broadband) *Provided by ISP
≥Use shielded LAN cables when connecting to peripheral 
devices.
≥Inserting any cable other than a LAN cable in the LAN 
terminal can damage the unit.≥Read the operating instructions for the Wireless LAN 
Adaptor DY-WL10 (optional) thoroughly when using it.
≥For up to date compatibility information on your Wireless 
router (Access Point) refer to
http://panasonic.jp/support/global/cs/
LANAV
OUT
LANWIRELESSRÉSEAU LOCALLAN
\(10BASE-T/100BASE-TX\)




LANWIRELESS




≥Only the Wireless 
LAN Adaptor 
DY-WL10 (optional)
can be used.
SC-BT230_330_730P_PC_VQT2M13_eng.book  17 ページ  ２０１０年３月１６日　火曜日　午後５時５７分 
						

							18
VQT2M13
STEP 4: AC power supply cord connection
Connect only after all other connections are complete.
AAC power supply cord (included)
(For units with PX printed on the packaging)
≥If the power plug does not fit your AC outlet, 
use the AC plug adaptor (included). If it still doesnt fit, 
contact an electrical parts distributor for assistance.
[BT730]
≥AC power supply cord with a label is for the wireless 
system. Do not use any other AC power supply cords 
except the supplied one.BTo a household AC outlet
Main unit
≥This unit consumes a small amount of AC power, even when it is turned off.
For the U.S.A. and Canada [BT730] [BT330]: approx. 0.05 W* [BT230] [BT235]: approx. 0.1 W*
For units with PX printed on the packaging [BT730] : approx. 0.1 W* [BT230]: approx. 0.2 W*
*When the “Quick Start” setting is “Off”
In the interest of power conservation, if you will not be using this unit for a long time, unplug it from the household AC outlet.
Wireless system [BT730]
For the U.S.A. and Canada: approx. 0.2 W
For units with PX printed on the packaging: approx. 0.3 W
STEP 5: [BT730] Preparing the wireless system
Turn on the wireless system after all connections are complete.
AC
220240V110127VVOLT ADJ
             

Main unit
The main unit shows SC-BT730 for the U.S.A. 
and Canada.
AC IN


[BT730]
Wireless system (For units with PX printed on the packaging)
Before connecting the AC power supply cord;
Set the voltage.
≥Use a flat-head screwdriver to move the voltage 
selector to the appropriate position for the area 
in which this system is used.
The socket outlet shall be installed near the equipment and easily accessible. The mains plug of the power supply cord shall 
remain readily operable. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug 
from AC receptacle.
WIRELESS LINKPOWER
WIRELESS LINK indicator
Red: The wireless system is on and the wireless link is deactivated.
Green : The wireless system is on and the wireless link is activated.
 (“ [W] ” is also displayed on the main unit’s display.)
Press [POWER CI, BÍ] on the wireless system.
Unit on/off button [POWER CI, BÍ]
CI:  The wireless system is on.
BÍ: The wireless system is off.
Wireless system
SC-BT230_330_730P_PC_VQT2M13_eng.book  18 ページ  ２０１０年３月１６日　火曜日　午後５時５７分 
						

							Getting started 
19
VQT2M13
STEP 6: Smart setup / Easy setup
The Smart setup / Easy setup assists you to make 
necessary settings.
Follow the on-screen prompts to make basic settings for the 
system.
[BT730] [BT330] : Smart setup
[BT230] [BT235]: Easy setup
Preparation
≥Turn on your TV and select the appropriate video input mode 
(e.g., VIDEO 1, AV 1, HDMI, etc.) to suit the connections to 
this unit. 
≥[BT730] [BT330] : Place the Auto speaker setup microphone at 
the actual seating position. (At ear level when seated.)
	≥Keep as quiet as possible during the Auto speaker setup. Excessive 
background noise may lead to incorrect settings.
≥The speakers output loud test signals during setup.
≥After the Smart setup is completed, unplug the Auto speaker setup 
microphone and keep it for future use.
1Press [Í].
2Follow the on-screen instructions and 
make the settings with [3,4,2,1] and 
press [OK].
Language
Select the language used on menu screen.
TV Aspect 
Select the aspect to suit your TV and preference.
[BT730] [BT330] [BT230] Wireless System
If a digital transmitter is inserted,
it is required to specify the current settings.
[BT330]* [BT235] [BT230]* Speakers position
Specify the positioning of the surround speakers.
* When using the optional wireless system, this setting 
is not available.
([BT730] only): “Speakers position” is not available.
[BT230] [BT235]: Speaker check
Check if the connection to each speaker is valid.
[BT730] [BT330] Auto Speaker Setup
Adjust the speaker output level automatically.
Speaker Output
Make surround sound setting for speaker output.
Cinema Surround
The function creates the sound of virtual speakers to 
enhance the realistic surround feeling as if the sound 
comes from all directions.
(Speakers position: Surround Layout only)
(Effective when playing video with 5.1/7.1ch audio)
TV Audio
Select the audio input connection from your TV,
[item with “(TV)”].
Quick Start
Speed of startup from power off is increased.
3Press [OK] several times to finish the 
“Smart setup” or “Easy setup”.
After completing “Smart setup” or “Easy setup”, you can 
perform “Network Easy Setting”.
	≥You can perform this setup anytime by selecting “Smart setup” or “Easy 
setup” in the Setup menu. (>38)
≥Language and TV Aspect settings are automatically retrieved if this unit is 
connected to a Panasonic TV (VIERA) supporting HDAVI Control 2 or later 
via an HDMI cable.
OKOK
SETUP MIC
e.g., [BT730]
SC-BT230_330_730P_PC_VQT2M13_eng.book  19 ページ  ２０１０年３月１６日　火曜日　午後５時５７分 
						

							20
VQT2M13
[BT730] [BT330] [BT230] 
1Select “Wired” or “Wireless” and press 
[OK].
If “Wireless LAN Adaptor is not connected.” is displayed, check 
that the Wireless LAN Adaptor is fully inserted. Alternatively, 
disconnect and reconnect it. If there is still no change in the 
display, consult your dealer.
2Follow the on-screen instructions and 
make the settings with [3,4] and press 
[OK].
For wireless LAN connection:
If you are using a Wireless router (Access point) that supports 
WPS, you can easily perform the settings by selecting “WPS 
(PUSH button method)”.
Otherwise, perform the settings by selecting “Search for 
access point” or “Manual setting” in “Other methods”.
≥WPS (Wi-Fi Protected Setup) is a function that facilitates 
settings relating to the connection and security of wireless 
LAN devices. To see whether your Wireless router (Access 
point) supports WPS, check the Wireless router operating 
instructions.
[BT235] 
Follow the on-screen instructions and make 
the settings with [3,4] and press [OK].
[BT730] [BT330] [BT230] Access Point Connection Setting
Network Easy Setting (Connection Check)
Network Easy Setting
OKRETURN
Network Easy Setting (Connection Check)
Wired
Wireless
A settings check for home network and Internet connections
is now being conducted.
Please select a connection mode first.
 
 Current setting  :  Wired
 
LAN cable connection:
 Connect a LAN cable to the unit and select “Wired.”
Wireless LAN connection:
 Insert a compatible Wireless LAN Adaptor to USB port 
 and select “Wireless.”
 Access point is necessary for Wireless LAN connection.
OKRETURN
Access Point Connection SettingSelect a connection method to use with an access point 
of Wireless LAN.
Please refer to the operating instructions of the access
point about connection methods.
WPS (PUSH button method)
Other methods
p
WPS (PIN code method)Search for access point
Manual setting
When you experience 
problems with settings
DisplayCheck the following
A conflict with another 
device occurred.≥Please wait a few moments, 
and then try again.
A time out error occurred.≥Setting of the Wireless 
router (Access point) for 
MAC Address etc.
≥The signal may be weak. 
Using the USB extension 
cable included with the 
Wireless LAN Adaptor, 
adjust the position of the 
Wireless LAN Adaptor.
≥The SSID* and the 
encryption key of the 
Wireless router (Access 
point).
≥Please wait a few moments, 
and then try again. An authentication error or a 
time out error occurred.
A device error occurred.≥Connection of Wireless LAN 
Adaptor
If there is no improvement in 
symptom, contact our 
Customer Service Center.
DisplayCheck the 
following
1. LAN cable connection or 
Connection to access point:Fail≥Connection of 
the LAN 
cables (>17)
2. IP address setting :Fail
3. Connection to gateway :Fail
OK
Access Point Connection SettingFailed to connect to the access point.
A conflict with another device occurred.
Do you want to configure Access Point Connection
Setting again ?
YesNo
OK
Network Easy Setting (Connection Check)
YesNo
Complete.
1. LAN cable connection         
2. IP address setting
3. Connection to gateway
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again. Select “No” and press [OK]
to finish Network Easy Setting.
: Fail
: Fail
: Fail
SC-BT230_330_730P_PC_VQT2M13_eng.book  20 ページ  ２０１０年３月１６日　火曜日　午後５時５７分