Panasonic BLC1A_20A Owners Manual

Operating Instructions
[For assistance, please call: 1-800-272-7033] 81
8.After you confirm the settings and click [Next>], set E-mail notification and click 
[Next>].
 If you select [Enable], the E-mail Notification When Triggered page is 
displayed. Enter the settings referring to page 
78 — page 80.
9.Click [Save] after confirming the settings.
 The new settings are saved.
 When finished, Success! is displayed.
SettingDescription
Disable The camera does not send an E-mail notification when...

Operating Instructions
82
10.Click [Go to Trigger page].
 The Trigger page is displayed.
Note 
 If you set a short interval when transferring to a cell phone, many E-mails 
will be sent, which may lead to a large phone bill. Therefore, we 
recommend you to set a long interval. 1 image per minute frequency is 
recommended.
 Motion Detection transfer stops operating until after the camera finishes 
all transfers. For example, if the camera transfers 3 images per minute and 
6 images in total by setting...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 83
4.4 Setting the Motion Detection
The Motion Detection page allows you to adjust the sensitivity of Motion Detection. 
Threshold: If the threshold is set low, this function detects nearly all movements.
Sensitivity: If you set sensitivity high, the amplitude of the motion detection bar gets 
jumpy.
1.Click [Motion Detection] on the Setup page.
2.Click the Motion Detection bar in Threshold to set the threshold level.
3.Click the Motion...

Operating Instructions
84
Note
No responsibility will be taken by our company with respect to consequences 
resulting from the use of the Motion Detection feature. The Motion Detection 
feature is not suitable and not recommended for uses that require a high 
reliability constantly such as surveillance, etc.
What is the threshold?
The threshold is the minimum value for the camera to detect motions on the image 
during the motion detection buffering. Setting the threshold lower allows subtler 
changes to...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 85
What is the sensitivity?
The sensitivity is the level of brightness detected as motion by the camera. A high 
sensitivity setting enables the camera to detect slight brightness changes. Lower 
the sensitivity to make the camera detect only big brightness changes.
Note
Lowering the threshold and increasing sensitivity enable the camera to easily 
detect slight movements on parts of the image.
Note
 Motion Detection is activated by...

Operating Instructions
86
4.5 Setting Sensor Log Notification
A sensor log sent once a day at a specified time can be checked. To enable Sensor 
Log, set Motion Detection for Trigger Setting and check [Enable].
1.Click [Sensor Log] on the Setup page.
When enabling the image/buffer transfer setting and selecting Motion 
Detection in the Trigger page, the Sensor log window is displayed.
2.Set each parameter.
Note
 Click [Save] to save the settings.
 Clicking [Cancel] cancels your settings without saving...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 87
SettingDescription
A setup of 
operation Sensor log operation can be set here.
Time Set the day of the week and time to send sensor logs via 
E-mail.
SMTP Server IP 
Address or Host 
Name
*1
 If you set a server IP address, set 4 numbers (0—255) and 
3 periods, such as 192.168.0.253. Note that 0.0.0.0 and 
255.255.255.255 are not available. Or set a host name 
(1—255 characters).
Po r t N o. Enter a number (1—65535). Usually set...

Operating Instructions
88
How to 
authenticateYou can select the authentication method: [No authentication], 
[POP before SMTP authentication] and [SMTP authentication].
POP server authentication may be required by your ISP. In 
that case, set POP before SMTP authentication.
 No authentication: No authentication when sending an e-
mail.
 POP before SMTP authentication: Some SMTP servers 
that send e-mails do not have an authentication feature. 
Therefore, the camera uses the authentication of a POP...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 89
5 Using Other Features
5.1 Changing Initial Settings on the Single 
Camera page or the Multi-Camera page
The Image Display page allows you to change the initial settings (display settings 
when a user accesses the camera) for the Single Camera, Multi-Camera, Limit 
Continuous Motion JPEG, Language and Banner Display.
1.Click [Image Display] on the Setup page.
2.Set each parameter.
 Clicking [Cancel] cancels your settings without...

Operating Instructions
90
SettingDescription
Image Resolution Select the image resolution.
640 × 480 pixels (Only for the Single Camera page)
320 × 240 pixels (default)
160 × 120 pixels (Only for the Multi-Camera page)
Image Quality Select the image quality.
[Favor Clarity] optimizes for good quality.
[Standard] offers standard quality. (default)
[Favor Motion] optimizes for enhanced motion.
Refresh Interval Select a refresh interval. 
(Motion, 3 s, 5 s, 10 s, 30 s, and 60 s)
Limit Continuous 
Motion...