Panasonic Audio Mixer Wr Xs3 Operating Instructions

21
■Example 1: Home Party (Mode 1)
•Set the DIP switches to Mode 1. (Refer to p. 15.).
•Mic 1 to 4 (MONO IN 1 to 4), Key (ST IN 1), Bass AMP (ST IN 2) and DVD/CD/MD (ST IN 3 and 4) are mixed to be output to
the main speakers (ST OUT L/R). 
•The power amplifier adjusts the output level of sound sources you want to confirm. These are then output to the foldback
loudspeakers (SUB OUT). 
•Recording is available through REC OUT when connecting a tape recorder or MD recorder to ST IN 3 and 4.
CONNECTION...

22
■Example 2: Presentation Room (Mode 2)
MONO IN 1REC OUTMONO IN 2MONO IN
3 to 4ST IN
1 to 4
LINE IN
SUB OUT
MONO OUTST OUT LST OUT RON
OFF
4
28
10 0164
28
10 0264
28
10 0364
28
10 046MONO
POWER4
28
10 0164
28
10 0264
28
10 0364
28
10 04644
22
88
10 0
10 0 66STMULTI IN4
28
10 06 SUB OUTSTEREOMONOSTEREO OUTINPUT
REAK
LINE INSUB4
2
8
10 06MONO OUTAudio Mixer WR-XS3
Ceiling speakers
DVD/CD
MD
TAPEVTR
TAPE(REC)
WR-XS3Projector
Note PC
Portable MD
Antenna for 
wireless microphone
Wireless 
microphone
Mic 1...

23
■Example 3: Shop (Mode 3)
ST OUT L
MONO IN 1MONO IN 2MONO IN 3MONO IN 4MULTI IN ST
MONO OUTSUB OUT
ST IN 
1 to 4
ON
OFF
4
28
10 0164
28
10 0264
28
10 0364
28
10 046MONO
POWER4
28
10 0164
28
10 0264
28
10 0364
28
10 04644
22
88
10 0
10 0 66STMULTI IN4
28
10 06 SUB OUTSTEREOMONOSTEREO OUTINPUT
REAK
LINE INSUB4
2
8
10 06MONO OUTAudio Mixer WR-XS3
CD
TAPE
WR-XS3Cable broad-
casting (BGM)
Shopping zone 1
 main speakersShopping zone 2
main speakersResting place (zone 3)
main speakers All-call Shop 1...

24
When you connect a cassette tape recorder or MD recorder to record the broadcasting, confirm the following:
■Notice about Recorder Connections
Howling can occur depending on the connection form or connected devices. Connect the recording devices either of the fol-
lowing ways:
●When Using a Recording-only and a
Playback-only Decks
The unit s REC OUT will be used for the recording output
line.
•Connect the units REC OUT with the recording decks
REC IN.
•Connect the unit s STEREO INPUT or MULTI INPUT...

25
■Recording and Playback with One Deck
To record and play back a broadcast with one deck, connect the SUB OUTPUT jack  to cut the feedback.
Then set the DIP switch associated with the MULTI INPUT ST jacks to OFF.
Note: Use the cable shown in the figure to connect the unit SUB OUT and the decks REC OUT.
To output either mono or stereo signal through REC OUT
The stereo and mono recording input signals are usually mixed through the REC OUT jack.
The internal switch setting is necessary if you want to...

26
STICKING LABELS
After the connection and settings, stick the supplied labels on the front panel of the unit.
The labels indicate the following:
•Name and level setting of each knob
•Mode setting
•Input line assigned to the SUB OUTPUT jack
■Label
■Where to Stick Labels
Stick the corresponding label in the corresponding position as shown in the figure.
Each label will be used as follows:
For MONO INPUT, For STEREO INPUT: for input line indication
For OUTPUT: for output line indication
MODE SETTING...

27
■Indication of Input Line Assigned to SUB OUT
Draw a line between SUB OUT and the assigned input connector, or black out the square.
The assigned input line will be identifiable.
Draw a line or black 
out to identify the 
assigned input line.SUB  OUT
MONO 1234 123
STEREO
4 

28
ATTACHING/DETACHING THE ACRYLIC COVER
The input levels need to be adjusted before using the unit.
After the adjustments, attaching the supplied acrylic cover
with mounting spacers and screws can prevent the wrong
operation of input levels. 
The acrylic cover protects the different range of input level
controls depending on the direction in which it is installed.
●The MULTI IN knob is adjustable.
●The MULTI IN knob is not adjustable.
Acrylic cover 
mounting spacers x 2
Acrylic cover Acrylic cover...

29
■Basic Operation
This section describes basic operation. All setup items and connections must be completed in advance.
The switches located under the acrylic cover normally do not need to be accessed for operation. Access is required only to
the switches outside the acrylic cover.
Confirm that the connections of all the devices and all set modes and input/output levels are correct.
Note:Set the STEREO OUT, MONO OUT and SUB OUT knob to “0” before operation.
1. Press the power switch on the front.
This...

30
■Input Level Adjustment
This section describes how to adjust input levels.
The figure describes an example. 
•Mode 1
•The microphone is connected to the MONO INPUT 1 connector and the CD player is connected to the STEREO INPUT 1
jack.
•The input signal of the MONO INPUT 1 connector and the STEREO INPUT 1 jack are mixed inside the unit, and amplified
through the STEREO OUTPUT jack.
Note:Detach the acrylic cover before the level adjustment. (Refer to p. 28 ATTACHING/DETACHING THE ACRYLIC COVER.)
4
28
10...