Panasonic Arbitrator360 Wireless Microphone Installation Guide

							900MHz Wireless Microphone  
Installation Guide
Note:
Please follow these instructions on how to install  
your 900MHz Wireless Microphone 
						

							1 
ARB-HT3G Wireless Mic  Receiver Connecon t\Po VP\f 1/2 
2ndWi reless  Mic 
Receiver  (Optional)
VPU (Rear)
To Au dio  In 2
To  In -C ar  Mic
To  
A udio  In 1 
Digital Wireless  Mic
Receiv er & Transmitte rReceiver (RX)
To  
Receiver  
Jack
DC  Po wer (Red) #1
To  J3  + Terminal
Po we r GND (Black) #2
To  J3  -Termina l
Receiver (RX)  
Cabl e
In-Car  Mic
Distribution  Center
Recording Trigger (Yello w) à#J1-
Tx /Rx Sy nc Status  (Green)  à#J1-
Mute  Indication  (White) à#J1-
àDistribution  Center
VPU  REC Status (Blue)  
à
#J1-21  (GPO1)
Tr igger GND (Black)  #J3-
à
Distribution  Center
ARB-HT3G Wireless Mic Receiver Connection to VPU 1/2 
						

							2 
ARB-HT3G Wireless Mic  Receiver Connecon t\Po VP\f 2/2 
1. Besides pow er and  GND lines, there are four trigger lines .
See the page 7 and connect each line properly  to the GPI inputs.
2. Powe r GND (#J3-) must be directly  connected to the Distribution Center .
3. Be sure to connect “blue” mic trigger labeled  “VPU Record” to GPO 
position  J1-21
     and set FE application  GPO setting according to instructions on page 18 of  
this manual.
1) Besides power and GND lines, there are four trigger lines.
2) Power GND (#J3-) must be directly connected to the Distribution Center. 
3)   Be sure to connect blue mic trigger labeled “VPU Record” to GPO position J1-21 
and set FE application GPIO.
ARB-HT3G Wireless Mic Receiver Connection to VPU 2/2 
						

							3 
ARB-HT3G Wireless Mic  Receiv er  
–  Tr igge r Congu raon  for Fr ont-End Applicaon ARB-HT3G Wireless Mic Receiver
Trigger Configuration for Front-End Application 
						

							4 
ARB-HT3G Wireless Mic  Receiv er  
– GPO Con\fgu ra\bon  for WMIC  Record Reset Featur e 
Note:
1) GPO  status must be set “REC” in order  for the reset feature  to function properl y.
2) WMIC  harness blue trigger line marked “VPU Rec” must be connected to po\
sition J1 -
21 in Power  Distribution Center . Please refer to page 15 for  proper connection  
informatio n
4 
ARB-HT3G Wireless Mic  Receiv er  
– GPO Con\fgu ra\bon  for WMIC  Record Reset Featur e 
Note:
1) GPO  status must be set “REC” in order  for the reset feature  to function properl y.
2) WMIC  harness blue trigger line marked “VPU Rec” must be connected to po\
sition J1 -
21 in Power  Distribution Center . Please refer to page 15 for  proper connection  
informatio nNote:
1) GPO status must be set to “REC” in order for the reset feature to function properly. 
2)  WMIC harness blue trigger line marked “VPU Rec” must be connected to position  
J1-21 in Power Distribution Center.
ARB-HT3G Wireless Mic Receiver
GPO Configuration for WMIC Record Reset Feature 
						

							©2014 Panasonic Corporation of North America. All rights reserved. Arbitrator 360 HD Wireless Microphone Installation Guide_05/14