Panasonic Arbitrator 360 Hardware Installation Manual

5. Wireless Mic Receiver Connection to VPU
1. Besides power and GND lines, there are three trigger  lines.
See the chart and connect each line properly to the GPI  inputs.
2. Trigger GND (#5) and power GND (#2) must be directl y connected 
to the Distribution Center. 

5-1. Wireless Mic Receiver Connection to VPU
Digital Wireless Mic
Receiver & Transmitter
Receiver (RX)To  
Receiver  
Jack
DC  Power (RED) #1 
To J3 + terminalPower GND (Black) #2 
To J3  - terminal
Recording Trigger (Brown) #7TX indication (Orange) #6Mute indication (white) #8-> Distribution Center
Distribution Center
2 nd
/ 3 rd
Wireless Mic 
Receiver (optional)
VPU (Rear)
To Audio In 3 and 4
To Audio In 2
To  
Audio In 1 
-> Distribution Center
Trigger GND (Black) #5 
To Distribution Center
Receiver...

6. 2nd
Rearseat Camera (Option:CN258IR-P) Connection to VP U
1. Backseat camera video output must be connected to Camera2  input in VPU
2. Power line (white) must be connected to Distribution  Center.
Power GND (black) must be directly connected to the Distri bution Center. 

6-1. 2nd
backseat Camera (Option:CN258IR-P) Connection to VP U
2nd
Camera
2nd
Camera 
Cable
Distribution Center
VPU (Rear)
White to J3 + terminal
Black J3 - terminal
Yellow to Camera 2              

7. Control Panel (Option: AG-RCP30P) Connection to VPU
Control Panel
Control Panel and Cable
VPU (Rear)               

8. Update Firmware by SDHC card/USB key
1. Put vup file (firmware)  right under root directory  in SDHC card or USB drive.
Don’t put any other folders / files.
2. Keep open the door and insert SDHC card or connect US B drive.
3. While pressing STOP button, turn power on, then keep  pressing STOP 
button for another 30 sec.
4.
VPU starts updating firmware, see the LEDs (below).
4.
VPU starts updating firmware, see the LEDs (below).
5. Once it’s finished (takes about 4 min), VPU reboots itse lf.
Keep...

Appendix 

Radioshack Part# 276-011 Lens size is 5mm 
 Red diffused lens color 
 Viewing angle is 60 °
°°
°
 30mA (max) 
 Typical Voltage is 12, with a maximum voltage of 12 V One per package 
If the Officer would like to see the REC/Error stat us from inside of vehicle 
additionally, it is possible to set up the LED ligh t connecting to GPIO
External GPIO Trigger (External LED)One per package Mfg hole diameter is 5/16 
RED
(+) cable connects to GPO1 (Pin#25) or GPO2 (Pin#8)
YELLOW
(-) cable connects to...

Special circuitry built within the cable allows Arbitrator Mobile Digital Video 
System to activate when police vehicle siren is tur ned on.
Siren Detector Cable (Option)
Overall length is 40 inches - minimum, 18 awg  
Max Input Voltage (Siren leads to Arbitrator RTN le ad): +/- 30V peak 
Min input frequency: 400 Hz  
Max output voltage: 15 VDC  
Operating temp: 0 ℃
℃℃
℃
to +65 ℃
℃℃
℃
Storage temp: -40 ℃
℃℃
℃
to +85 ℃
℃℃
℃
Contact Information:LIND Electronicshttp://www.lindelectronics.com/Toll Free...

G-Force Sensor (Option) ConnectionTGS-3DP 

Black (GND: - ):   
Connect to the Distribution CenterRed (BATT: +):Connect  to the Distribution Center
Connect each cable to the  
Distribution Center