Panasonic Arbitrator 360 Hardware Installation Manual

Arbitrator 360 
Hardware Installation ver 2.4Hardware Installation ver 2.4(Distribution Center version) 

1. Arbitrator Units and CablesCamera Cable(Short)
Camera
AG-CK10P
AG-CPD20P
Recorder (VPU)
32GB SDHC Card Camera MountCamera Cable
(Long)
RP-SDW32GP1K
PAPDC2462-2859
TT-ARBM56P06
External GPIO  
Trigger Cable
CCR24PNA
Digital Wireless Mic Reciever &  Transmitter In Car Mic
Receiver Cable Control Panel 
Cable
Control Panel
2
nd
Backseat 
Camera
CN258IR-P
LAN Cable 
(Crossing type)
GPS Antenna
Power Cable 
for Recorder
AG-RCP30P
3 rd
-6th Camera
OPTIONS
Power 
Distribution Box
AP-WiFi-ModemA360-WLSAP-BWT...

GPS Antenna
Camera 2 
(backseat) (Option)
CN258IR-P
VPU
AG-CPD20P
2. Arbitrator in-car System Configuration
Front End
Application
Ethernet 
Cable for  Wired 
Upload
Toughbook 
(In car PC)
Option
Camera Examples
Camera 3 (LPR) Camera 4 (Left)
Camera 5 (Right)
Camera 6 (Back)
Control Panel
(Option)
AG-RCP30PVideo Out 1  for LPR/ 
Monitor etc
Cable KitAG-CR13P
Power 
Distribution BoxAntenna
Car Battery 12V/24V 16 Triggers  
(Siren/Light  
Bar/Brake/
WMIC etc)
2nd
/3 rd
WMIC  
RX/TX(Option)
RX/TX
WMIC...

Appendix: Camera 4, 5 and 6 video image and connection
If Left Camera (Cam4), Right Camera (Cam5) and Back Camera 
(Cam6) have the Mirror mode
, Connect Cam 4 to the “video in 4”, 
Cam5 to “video in 5” and Cam6 to “video in 6”
Front LPR
Right
Left
Back
R-Seat
1 (Camera 1)
2 3
Cam4
Cam5
Cam6
6 5
4
1, 2 or 3
4 5 61, 2 or 3
Image will be moved 4, 6, 5 in order from left to r
ight.Cam4
Cam5 Cam4
Cam5
Officer Walking Direction
Image will be moved 4, 6, 5 in order from left to r ight.
If Left Camera (Cam4),...

3. Install VPU using Mounting Bracket
1. To center console
2. To trunk    

4. Power cable harness for VPU, Wireless MIC and 2nd
camera
(Distribution Center)   

4. Power cable harness for VPU, Wireless MIC and 2nd
camera
(Distribution Center inside picture)   

Recording engine
ClockVPU
Power sw
signal(SA)
■ ■
■
Car Battery
12V/24V 
WHITEREDBLACK
Fuse
10A
Fuse7.5A
(+)
(-)
power
ACC switch
10A fuse 
7.5A fuse
Please set  
“Power Off Time”  
to be minimum 10 min 
in FE “Config” setting  
in order to close the  
file properly.
4-1. Power cable harness for VPU, Wireless MIC and 
2nd
camera
(Distribution Center)
1A  in-line fuse
Receiver (RX) Cable
WMIC Receiver (RX)
Trigger GND #5
RED #1
2nd ~6th
Camera
WHITEBLACK
Power GND #2      

4-2. GPIO Trigger for 16 GPIs
Distribution Center
Signal Remark J1 Input # Trigger Name (Example)
GPI 1 In J1-1 Wireless Mic 
GPI 2 In J1-2 Light Bar
GPI 3 In J1-3 Brake Indicator
GPI 4 In J1-4 Siren Indicator 
GPI 5 In J1-5 Gun Lock 
GPI 6 In J1-6 Wireless Mic Active indicator        (H)
GPI 7 In J1-7 Wireless Mic Mute indicator           (H )
GPI 8 In J1-8 Other 
GPI 9 In J1-9 Other
GPI 10
In
J1
-10
Other
GPI 10
In
J1
-10
Other
GPI 11 In J1-11 Other 
GPI 12 In J1-12 Other 
GPI 13 In J1-13 Other 
GPI 14...

4-3. GPIO Trigger for 16 GPIs Blank Sheet
Distribution Center
Signal Remark J1 Input # Trigger Name (Example)
GPI 1 In J1-1 
GPI 2 In J1-2
GPI 3 In J1-3
GPI 4 In J1-4 
GPI 5 In J1-5 
GPI 6 In J1-6
GPI 7 In J1-7
GPI 8 In J1-8 
GPI 9 In J1-9
GPI 10
In
J1
-10
GPI 10
In
J1
-10
GPI 11 In J1-11 
GPI 12 In J1-12 
GPI 13 In J1-13 
GPI 14 In J1-14
GPI 15 In J1-15
GPI 16 In J1-16 
GPO 1 Out J1-21 
GPO 2 Out J1-22
GPO 3 Out J1-23 
GPO 4 Out J1-24
GPI 1~16     L : not more than1.0V         H: 4 V t o 28V...