Panasonic All-in-One Headset Wx Ch2050 Operating Instructions

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
All-in-One Headset
Operating Instructions
Model No.WX-CH2050
ENGLISH
FRANÇAIS 

2
The serial number of this product may be found in the bat-
tery compartment of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No. WX-CH2050
Serial No.
CAUTION
It is a violation of Federal Law to begin operating this sys-
tem prior to obtaining an FCC Radio License. The FCC ID
number for this radio equipment is listed below.
FCC ID: ACJ9TAWX-CH2050
ATTENTION:
A...

3
INTRODUCTION
The WX-CH2050 is an all-in-one headset designed for use in wireless communication systems, which are use in Drive thru
menu boards, etc. It incorporates such necessary devices as a microphone and earphone, as well as a battery compartment
and control buttons. With the built-in antennas, transmitter, and receiver you can communicate by voice with other store per-
sonnel and the customer.
FEATURES
•Compatible center modules: WX-C1010 and WX-C1011
•Less noise and interference thanks to the...

4
1
2
3
4
5
6 7 8SERVICE 
USE ONLYGROUP
FUNCTIONOFF
ON
E
JECT
A/B
VOL.
!1
!2
!3
!4
!5
q
r
e
w
u
i
o!0y
t
NAMES & FUNCTIONS 

5
qHead Band and Head Pad
Adjustable to your head by sliding the head pad.
wBattery Lock [EJECT]
When removing the battery, slide out the lock.
When loading a new battery, insert the battery until the
lock clicks.
eBattery (Optional accessory)
See PRECAUTIONS.
rHead Pad Cushion
tStrap (Standard accessory)
ySwitch Pocket
Do not open the lid. Should be opened only by qualified
service personnel or system installers.
uEarphone Pad
iMicrophone Boom
Adjust the microphone position to your mouth by rotat-
ing...

6
OPERATING PROCEDURES
Notes:
•Transmission using the talk [T] or page [P] button is
allowed for a single headset at a time. A continuous
beep or distorted sound will be heard in a headset that
tries to transmit while another person is operating.
•Maintain a distance of more than 0.3 m (1 ft) between
the headset and the order taker, or more than 1 m (3 ft)
between the headset and the center module.
●Preparations
Prior to operating the headset, confirm that the system
setup for the headset, center module,...

7
●Communications with Customers
[TALK]
Any store personnel wearing the headset can communicate
bidirectionally with any customer who is at the menu board.
1. Select a proper sound level by pressing the [
▲] or [▼]
button.
2. You will hear a tone in the headset when a vehicle
arrives at the menu board.
Note:The tone duration varies depending on the set-
tings made in the center module. 

1. Press the talk [T] button and speak to the customer.
A short beep repeats in the headset.
2. Press the button again...

8
BATTERY LOADING & 
REPLACEMENT
Notes:
•Refer to operating instructions included with the battery
and battery charger.
•Battery replacement is recommended when the power
indicator lights up in red and a pulsing beep is heard in
the headphone.
●Loading
1. Prepare a fully charged battery.
2. Insert the battery as shown in the figure.
Note:Be sure to insert it until the lock clicks.
●Replacement
1. Slide the battery lock to the outside.
2. Remove the battery.
3. Proceed as described in Loading above....

9
SPECIFICATIONS
Operating Frequency: UHF/FM
Type of Radio Wave: F3E
Required Power Supply: Rechargeable Li-ion Battery, 3.7 VDC, normal type or long life type
Control Function:  Power (On/Off)
Volume (Up/Down)
Talk
Page
Channel Selection (A/B)
Channel Group Selection (1-8)
DIP Switch Setup (8 bit)
Dimensions: 140 mm(W) x 240 mm(H) x 84 mm (D)
5-1/2 (W) x 9-7/16 (H) x 3-5/16 (D)
Weight (excluding battery): 160 
g(0.35 lbs)
STANDARD ACCESSORIES
Windproof Cushion...

10
SETUP PROCEDURES
Caution:Setup of this product should only be performed
by qualified service personnel or system installers.
●Opening the Switch Pocket
1. Press the power button to turn off the headset. 
2. Open the switch pocket adjacent to the ear pad using
the supplied screwdriver. 
3. Set the switches as described below.
4. After finishing the setup, turn on the headset.
5. Replace the lid.
●Channel Group Selection
You can select a channel group by setting the rotary switch
inside the pocket....