Panasonic Aj Yac930g Operating Instructions Manual

SDTI Interface Board
Operating Instructions
Model No.AJ- G
Printed in Japan
S0802T @
VQT9964
Before operating this product, please read the instructions
carefully and save this manual for future use. 

2(E)
Precautions
ODo not touch the product with wet hands.
ODo not drop the product or expose it to bumps or shocks.
ODo not attempt to modify the product.
Doing so could cause it to malfunction.indicates safety information.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD AND ANNOYING INTERFERENCE,
USE THE RECOMMENDED ACCESSORIES
ONLY.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, REFER MOUNTING OF THE
OPTIONAL INTERFACE BOARD TO
AUTHORIZED SERVICE PERSONNEL. 

3(E)
Contents
Precautions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
For use with:  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Features  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Accessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Installing the board  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Specifications  . . . . . . . . . . . . . . . . . . . . . ....

4(E)
Installing the board
1Disconnect the power cord from the VTR.
2Remove the 2 coin screws, then remove the top panel.
CAUTION:
These servicing instructions are for use by qualified
service personnel only.  To reduce the risk of fire or
electric shock do not perform any servicing other
than that contained in the operating instructions
unless you are qualified to do so.
Coin screws 

5(E)
Installing the board
3Loosen the screw indicated in the diagram below, then
remove the board clamp.
Screw Board clamp
4Remove the screw, then remove the blank panel from
the rear panel.
Screw Blank panel 

6(E)
Installing the board
6Attach the accessory connector board to the rear panel.
As shown in the diagram below, after passing the SDI
board’s connecting cables through the hole provided for
the F3 slot, plug them into the top section of the
connector board and then fix the connector board in
place using the screw.
Hole for the F3 slot Rear panel SDI board’s connecting cables
5Remove the SDI board from the F3 slot on the rear
panel side of the VTR unit.
Screw Connector
board
SDI board 

7(E)
Installing the board
7Connect the connecting cables to the SDTI board.
8Reinsert the SDI board in the F3 slot, then insert the
SDTI board in the same F3 slot located on the front
panel side.
Position the cables as shown
in the diagram.
Yellow: SDTI OUT2
Orange: SDTI OUT1
Black: SDTI IN
SDTI board
F3 

8(E)
Installing the board
9Reattach the board clamp using the screw, then fix the
top panel in place using the 2 coin screws.
ScrewCoin screws
Board clamp
Refer to the operating instructions of the digital VTR
being used for details on the settings, operation,
warning messages, etc. 

9(E)
Specifications
$SDTI board
Dimensions (WaHaD):
5 11/16a5 7/8a9/16inch (143a148a13 mm)
Weight:
0.2244 lb (102 g)
$Input/Output:
SDTI IN (audio/video data):
BNCa1 
(complies to the SMPTE 305M/321M standard)
SDTI OUT (audio/video data):
BNCa2 
(complies to the SMPTE 305M/321M standard) 

ji
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANYUNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICAExecutive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094   (201) 348-7000
EASTERN ZONE: 
One Panasonic Way 4E-7, Secaucus, NJ 07094   (201) 348-7621
Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024   (770) 338-6835
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123   (847) 468-5200
WESTERN ZONE: 
3330 Cahuenga Blvd W., Los Angeles, CA 90068   (323) 436-3500...