Panasonic Aj Spx800p Operating Instructions Manual

							101
8
8-4-6 MODE CHECK IND 8-4-7  !LED

If both GAIN (0 dB) and GAIN (–3 dB) are set to ON, the LED
illuminates except when GAIN is adjusted to 0 dB and –3 dB. 
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
STATUS ONOFFSelect whether or not to display the status 
indication during MODE CHECK. 
–CUFE
!LED ONOFFSelect whether or not to display the cause 
indication screen when the ! LED turns on 
during MODE CHECK 
–CUFE
FUNCTION ONOFFSelect whether or not to display the 
FUNCTION indication screen during MODE 
CHECK. 
–CUFE
AU D I O O NOFFSelect whether or not to display the AUDIO 
indication screen during MODE CHECK. 
–CUFE
P.ON IND ONOFFSelect whether or not to display the status 
indication screen after the power is turned 
ON. 
–CUFE
Items/
Data Saved Adjustable 
Range Remarks
GAIN(0dB) ONOFFSelect whether or not to illuminate when 
GAIN is set to other than 0 dB.
–CUFE
GAIN (-3dB) ON
OFFSelect whether or not to illuminate when 
GAIN is set to other than -3 dB.
–CUFE
DS.GAIN ON
OFFSelect whether or not to illuminate when 
DS.GAIN (storage gain) is ON. 
–CUFE
SHUTTER ONOFFSelect whether or not to illuminate when the 
shutter is set to ON. 
–CUFE
WHITE 
PRESETON
OFFSelect whether or not to illuminate when the 
WHITE BAL switch is set to PRST. 
–CUFE
EXTENDER ONOFFSelect whether or not to illuminate when the 
lens is in EXTENDER mode. 
–CUFE
BLACK STR ON
OFFSelect whether or not to illuminate when 
BLACK STRETCH is used. 
–CUFE
MATRIX ON
OFFSelect whether or not to illuminate when 
MATRIX is set to ON. 
–CUFE
COLOR 
CORRECTIONON
OFFSelect whether or not to illuminate when 
COLOR CORRECTION is set to ON. 
–CUFE
FILTER ON
OFFSelect whether or not to illuminate the lamp 
when filter1 (3200K) is not 3200K.
–CUFE
SUPER V ON
OFFSelect whether or not to illuminate when 
SUPER V is set to ON. 
–CUFE
50M/25M/DV OFFW/O 50M
W/O 25M
W/O DVSelect whether or not to illuminate according 
to the recording mode. 
OFF:Does not illuminate in any recording 
mode. 
W/O 50M:
Illuminate except in DVCPRO50 
mode. 
W/O 25M:
llluminate except in DVCPRO mode. 
W/O DV:
Illuminate except in DV mode. 
–CUFE
AT W
ON
OFFSelect whether or not to illuminate when 
auto-tracking white balance is allocated to 
the WHITE BAL switch B. 
–CUFE
D.ZOOM ON
OFFSelect whether or not to illuminate during 
digital zoom operation. 
–CUFE 
						

							102
8-5 CAM OPERATION
8-5-1 CAMERA ID

This setting is canceled when READ FACTORY DATA is
selected. 
8-5-2 SHUTTER SPEED8-5-3 SHUTTER SELECT
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
ID1Setting 1 for the CAMERA ID recorded on 
color bars. Up to 10 characters are allowed 
for this setting.
–CUF –
ID2Setting 2 for the CAMERA ID recorded on 
color bars. Up to 10 characters are allowed 
for this setting.
–CUF –
ID3Setting 3 for the CAMERA ID recorded on 
color bars. Up to 10 characters are allowed 
for this setting.
–CUF –
Items/
Data Saved Adjustable 
Range Remarks 
SYNCHRO 
SCANONOFFAllocate SYNCHRO SCAN as a shutter 
speed selectable by the shutter switch. 
–CUFE
SUPER V ON
OFFAllocate SUPER V as a shutter speed 
selectable by the shutter switch. 
–CUFE
POSITION1 ONOFFAllocate the shutter speed set by POSITION 
SELECT in the  
screen as the shutter speed selectable by 
the shutter switch. 
–CUFE
POSITION2 ONOFFAllocate the shutter speed set by 
POSITION2 SELECT in the  screen as the shutter speed 
selectable by the shutter switch. 
–CUFE
POSITION3 ONOFFAllocate the shutter speed set by 
POSITION3 SELECT in the  screen as the shutter speed 
selectable by the shutter switch. 
–CUFE
POSITION4 ONOFFAllocate the shutter speed set by 
POSITION4 SELECT in the  screen as the shutter speed 
selectable by the shutter switch. 
–CUFE
POSITION5 ONOFFAllocate the shutter speed set by 
POSITION5 SELECT in the  screen as the shutter speed 
selectable by the shutter switch. 
–CUFE
POSITION6 ONOFFAllocate the shutter speed set by 
POSITION6 SELECT in the  screen as the shutter speed 
selectable by the shutter switch. 
–CUFE
Items/
Data Saved Adjustable 
Range Remarks
SUPER V 
MODEFRM1FRM2Select the SUPER V switching mode. 
FRM1: Normal mode. 
FRM2: After-image reduction mode. 

The SUPER V mode increases vertical 
resolution by directly outputting the photo-
diode vertical signal from the CCD. FRM1 
sets the accumulation level to 1/30th 
second. FRM sets the level to 1/60th 
second, reducing sensitivity by half. 
–CUFE
POSITION1 
SEL1/1001/120
1/250
1/500
1/1000
1/2000Select the shutter speed to be allocated to 
POSITION1. 
–CUFE
POSITION2 
SEL1/100
1/120
1/250
1/500
1/1000
1/2000
Select the shutter speed to be allocated to 
POSITION2. 
–CUFE
POSITION3 
SEL1/100
1/120
1/250
1/500
1/1000
1/2000
Select the shutter speed to be allocated to 
POSITION3. 
–CUFE
POSITION4 
SEL1/100
1/120
1/250
1/500
1/1000
1/2000
Select the shutter speed to be allocated to 
POSITION4. 
–CUFE
POSITION5 
SEL1/100
1/120
1/250
1/500
1/1000
1/2000
Select the shutter speed to be allocated to 
POSITION5. 
–CUFE
POSITION6 
SEL1/100
1/120
1/250
1/500
1/1000
1/2000Select the shutter speed to be allocated to 
POSITION6. 
–CUFE 
						

							103
8
8-5-4 USER SW

For each function of the USER switches, refer to [4-9-4
Assigning Functions to USER MAIN, USER1 and USER2
Buttons].
8-5-5 SW MODE
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
USER MAIN SW INH
S.GAIN
DS.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
D. Z O O M
AT W
Y GET
NEWS-G.
AUD IO  CH 1
AUD IO  CH 2
REC SW
RET SW
SLOT SELAllocate the USER MAIN button. 
–CUFE
USER1 SW INH
S.GAIN
DS.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
D. Z O O M
AT W
Y GET
NEWS-G.
AUD IO  CH 1
AUD IO  CH 2
REC SW
RET SW
SLOT SEL
Allocate the USER1 button. 
–CUFE
USER2 SW INH
S.GAIN
DS.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
D. Z O O M
AT W
Y GET
NEWS-G.
AUD IO  CH 1
AUD IO  CH 2
REC SW
RET SW
SLOT SEL
Allocate the USER2 button. 
–CUFE
Items/
Data Saved Adjustable 
Range Remarks
RET SW RECCHECKCAM RET
Select the RET switch function. 
REC CHECK:
 Perform REC REVIEW. 
CAM RET:
 Perform return signal output. 
–CUFE
S.BLK LVL OFF
–10
–20
–30
Set the super black level. 
–CUFE
AUTO KNEE 
SWONOFFSelect whether or not to use the AUTO 
KNEE switch. 
SCUF E
SHD,ABB SW 
CTLONOFFSelect whether or not to enable the 
automatic black shading adjustment if the 
ABB switch has been pressed for 5 seconds 
or more. 
–CUFE
COLOR BARS SMPTEFULL
BARS
SPLIT
ARIBSelect the color bars to use. 
SMPTE:Use the SMPTE color bars. 
FULL BARS:Use full color bars. 
SPLIT:Use SPLIT color bars. 
ARIB:Use ARIB multi-format color 
bars. 
–CUFE
S.GAIN OFF L/M/HS.GAINSelect when the SUPER GAIN mode is 
disabled. 
L/M/H:Disabled when the gain selector 
switch is operated. 
S.GAIN:Disabled only with the S.GAIN switch 
(USER button). 
–CUFE
DS.GAIN OFF L/M/H
DS.GAINSelect when the DIGITAL SUPER GAIN 
mode (stored gain) is disabled. 
L/M/H:Disabled when the gain selector 
switch is operated. 
S.GAIN:Disabled only with the S.GAIN switch 
(USER button). 
–CUFE
ECU DATA 
SAVEON
OFFON:Store the values set and adjusted 
with the ECU when the ECU is 
disconnected from the camera-
recorder. 
OFF:Does not store camera-related set 
values. 
–CUF –
ECU REC CHK 
SWR.REVIEWPLAYSelect the camera-recorder operation to be 
performed when the ECU REC CHECK 
button is pressed.
R.REVIEW:Perform REC REVIEW. 
PLAY:Play back the most-recently 
recorded clip from the beginning. 
–CUFE 
						

							104
8-5-6 WHITE BALANCE MODE 8-5-7 USER SW GAIN
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
FILTER INH ONOFFSelect whether or not to retain white balance 
memory (A/B) data for individual filters. 
ON:Retain data in the A/B memory (2 
memory areas) regardless of the 
filters. 
OFF:Retain data for individual filters. 
–CUFE
SHOCKLESS 
AW BOFF
FA S T
NORMAL
SLOW1
SLOW2
SLOW3
Set SHOCKLESS AWB to ON (FAST/
NORMAL/SLOW1-3) or OFF. 
SHOCKLESS AWB eliminates the shock 
caused by switching the WHITE BAL 
switch’s PRST/A/B setting. The switching 
time can also be selected. 
–CUFE
AWB AREA 25%50%
90%Switch the AWB detection area. 
25%:Detect 25% of area around the 
screen center. 
50%:Detect 50% of area around the 
screen center. 
90%:Detect 90% of area in the full screen. 
–CUFE
AWB & ABB 
OFFSETON
OFFSelect whether or not to reset the GAIN and 
PED values in the ROP menu when AWB 
and ABB are executed. 
ON:Do not reset. 
OFF:Reset values. 
–CUFE
COLOR TEMP 
PRE3200K : 5600K
Set the AWB PRE color temperature. 
–CUFE
AW B A ME MVA RSelect the function to be allocated to WHITE 
BAL switch A. 
MEM:Function to store values set by 
executing the auto white balance. 
VAR:Function to apply color temperature 
set by COLOR TEMP A. 
–CUFE
COLOR TEMP 
A3200K : 5600K
Set the color temperature when VAR is 
selected under AWB A. 
–CUFE
AW B B ME MAT W
VA RSelect the function to be allocated to WHITE 
BAL switch B. 
MEM:Function to store values set by 
executing auto white balance. 
AT W :Function to execute auto-tracking 
white balance. 
VAR:Function to apply color temperature 
set by COLOR TEMP B. 
–CUFE
COLOR TEMP 
B3200K : 5600K
Set the color temperature when VAR is 
selected under AWB B. 
–CUFE
ATW SPEED NORMALSLOW
FA S TSelect the control speed for the auto-
tracking white balance. 
–CUFE
Items/
Data Saved Adjustable 
Range Remarks
S.GAIN
30 dB_•Select whether or not to enable 30dB for 
SUPER GAIN. 
_: Enable. 
 • :  Disable. 
–CUFE
36 dB_•Select whether or not to enable 36dB for 
SUPER GAIN. 
_: Enable. 
 • :  Disable. 
–CUFE
42 dB_•Select whether or not to enable 42dB for 
SUPER GAIN. 
_: Enable. 
 • :  Disable. 
–CUFE
48 dB_•Select whether or not to enable 48dB for 
SUPER GAIN. 
_: Enable. 
 • :  Disable. 
–CUFE
DS.GAIN
6 dB(1/30)
_•Select whether or not to enable 6 dB (1/30) 
for DS.GAIN. 
_: Enable. 
 • :  Disable. 
–CUFE
12 dB(1/15)_•Select whether or not to enable 12 dB (1/15) 
for DS.GAIN. 
_: Enable. 
 • :  Disable. 
–CUFE
20 dB(1/6)_•Select whether or not to enable 20 dB (1/6) 
for DS.GAIN. 
_: Enable. 
 • :  Disable. 
–CUFE 
						

							105
8
8-5-8 IRIS
8-6 MAIN OPERATION
8-6-1 BATTERY/P2CARD
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
A.IRIS LEVEL 000 : 050 : 100
Set the target value for auto iris. 
–CUFE
A.IRIS PEAK/
AV E000 : 040 : 100
Determine the peak-to-standard ratio for the 
auto iris. 
A larger value sets the auto iris to respond to 
the peak in the IRIS detection window, while 
a smaller value sets it to respond to the 
average value in the window. 
–CUFE
A.IRIS MODE NORM1
NORM2
CENTR
Select the auto iris detection window. NORM1:The window closer to the center of 
the screen. 
NORM2:The window closer to bottom of the 
screen. 
CENTR:The spot window in the center of the 
screen.  –CUFE
S.IRIS LEVEL 000 : 080 : 100
Set the target value for the super iris. 
–CUFE
IRIS GAIN CAM
LENSSelect which unit controls IRIS GAIN. 

Lenses with an extender, such asC2, C0.8 
sold before FUJINON DIGI POWER, 
perform IRIS compensation while enabling 
the extender. Therefore, if this setting is 
switched to CAM, the camera’s iris control 
will not operate properly. 
–CUFE
IRIS GAIN 
VA L U E01 : 08 : 20
Set the adjustable value for IRIS GAIN. This 
setting is effective when CAM is selected for 
IRIS GAIN. 
–CUFE
Items/
Data Saved Adjustable 
Range Remarks
BATTERY 
SELECTPRO14TRIM14
HYTRN50
HYTRN100
HYTRN120
DIONIC90
DIONIC160
HP-90L
BP-H120
NP-L50
ENDURA50
ENDURA80
BP-L60/90
NiCd14
NiCd13
NiCd12
TYPE A
TYPE BSelect the battery to use. Remaining 
capacity detection is also performed 
according to the selected battery. 
The selectable battery types change 
depending on the settings under [8-6-2 
BATTERY SETTING1] and [8-6-3 BATTERY 
SETTING2]. 
–CUF –
EXT DC IN 
SELECTAC _ AD PTPRO14
TRIM14
HYTRN50
HYTRN100
HYTRN120
DIONIC90
DIONIC160
HP-90L
BP-H120
NP-L50
ENDURA50
ENDURA80
BP-L60/90
NiCd14
NiCd13
NiCd12
TYPE A
TYPE BSet the remaining capacity detection type 
when a battery is connected to the DC IN 
connector. Remaining capacity detection is 
also performed according to the selected 
battery type. 
The selectable battery types change 
depending on the settings under [8-6-2 
BATTERY SETTING1] and [8-6-3 BATTERY 
SETTING2]. 

The % display is disabled even when a 
digital battery is connected to the DC IN 
connector. 
–CUF –
BATT NEAR 
END ALARMON
OFFSelect whether or not to set the alarm to 
beep for BATT NEAR END ALARM. 
–CUF –
BATT NEAR 
END CANCELONOFFIf set to ON, the warning tone and indication 
can be canceled by pressing the MODE 
CHECK button when BATT NEAR END 
ALARM is triggered. 
–CUF –
BATT END 
ALARMONOFFSelect whether or not to set the alarm to 
beep for BATT END ALARM. 
–CUF –
BATT REMAIN 
FULL100%
70%Set the display content of the remaining 
battery capacity indicator bars in the display 
window when using a digital battery. 
100%: Indicate FULL at 100% capacity. 
70%: Indicate FULL at 70% capacity. 
–CUF – 
						

							106
8-6-2 BATTERY SETTING1
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
CARD NEAR 
END ALARMON
OFFSelect whether or not to set the alarm to 
beep for P2 CARD NEAR END ALARM. 
–CUF –
CARD NEAR 
END TIME 3min
2minSet the remaining time to indicate the P2 
CARD NEAR END TIME alarm. 
–CUF –
CARD END 
ALARMONOFFSelect whether or not to set the alarm to 
beep for P2 CARD END ALARM. 
–CUF –
CARD REMAIN/„5min/„3min/„Set the length of time for one segment („) of 
the P2 card’s remaining capacity indicator 
bars. 
5min:One segment represents 5 minutes. 
3min:One segment represents 3 minutes. 
–CUF –
Items/
Data Saved Adjustable 
Range Remarks
PRO14_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AU TOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO :Set voltage automatically. 
MANUAL:Set voltage manually. 11.0 : 13.7 : 15.0
When MANUAL is selected in the above 
menu, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
TRIM14_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AU TOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO :Set voltage automatically. 
MANUAL:Set voltage manually. 11.0 : 13.6 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
HYTRON50_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AU TOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO :Set voltage automatically. 
MANUAL:Set voltage manually. 11.0 : 13.1 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
HYTRON100_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AU TOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO :Set voltage automatically. 
MANUAL:Set voltage manually. 11.0 : 13.2 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
HYTRON120_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AU TOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO :Set voltage automatically. 
MANUAL:Set voltage manually. 11.0 : 13.1 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF – 
						

							107
8

The remaining battery capacity for digital batteries is displayed
as % inside the viewfinder (PRO14/TRIM14/HYTRON50/
HYTRON100/HYTRON120/DIONIC90/DIONIC160/NP-L50). 
The BATT NEAR END alarm, however, is triggered according to
the setting on the  screen, regardless of
the % indication. 
The ____ in the Adjustable Range column indicates the preset
mode.
Items/
Data Saved Adjustable 
Range Remarks 
DIONIC90_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AUTOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO:Set voltage automatically. 
MANUAL:Set voltage manually. 
11.0 : 13.6 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
 DIONIC160_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AUTOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO:Set voltage automatically. 
MANUAL:Set voltage manually. 11.0 : 13.3 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
HP-90L_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AUTOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO:Set voltage automatically. 
MANUAL:Set voltage manually. 
11.0 : 12.4 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
BP-H120_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AUTOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO:Set voltage automatically. 
MANUAL:Set voltage manually. 11.0 : 11.5 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
NP-L50_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AUTOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO:Set voltage automatically. 
MANUAL:Set voltage manually. 
11.0 : 13.0 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
Items/
Data Saved Adjustable 
Range Remarks
ENDURA50_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AU TOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO :Set voltage automatically. 
MANUAL:Set voltage manually. 
11.0 : 13.1 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
ENDURA80_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AU TOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO :Set voltage automatically. 
MANUAL:Set voltage manually. 11.0 : 13.1 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF –
BP-L60/90_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
AU TOMANUALSelect auto or manual to set the NEAR END 
voltage. 
AU TO :Set voltage automatically. 
MANUAL:Set voltage manually. 
11.0 : 11.2 : 15.0
When MANUAL is selected in the menu 
above, set the NEAR END voltage in 0.1 V 
steps. 
–CUF – 
						

							108
8-6-3 BATTERY SETTING2
The ____ in the Adjustable Range column indicates the preset
mode.
Items/
Data Saved Adjustable 
Range Remarks 
NiCd14_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
NEAR END 11.0 : 13.6 : 15.0
Set the NEAR END voltage in 0.1 V steps. 
END
11.0 : 13.2 : 15.0
When MANUAL is selected in the menu 
above, set the END voltage in 0.1 V steps. 
–CUF –
NiCd13_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
NEAR END 11.0 : 12.7 : 15.0
Set the NEAR END voltage in 0.1 V steps. 
END
11.0 : 12.2 : 15.0
When MANUAL is selected in the menu 
above, set the END voltage in 0.1 V steps. 
–CUF –
NiCd12_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
NEAR END 11.0 : 11.5 : 15.0
Set the NEAR END voltage in 0.1 V steps. 
END
11.0 : 11.2 : 15.0
When MANUAL is selected in the menu 
above, set the END voltage in 0.1 V steps. 
–CUF –
TYPE A_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
FULL 12.0 : 15.0 : 17.0
Set the voltage to display the FULL 
indication in 0.1 V steps. 
NEAR END 11.0 : 13.6 : 15.0
Set the NEAR END voltage in 0.1 V steps. 
END
11.0 : 13.2 : 15.0
When MANUAL is selected in the menu 
above, set the END voltage in 0.1 V steps. 
–CUF –
Items/
Data Saved Adjustable 
Range Remarks 
TYPE B_•Enable selection under BATTERY SELECT. 
_:Enable selection. 
 • : Disable selection. 
FULL 12.0 : 13.5 : 17.0
Set the voltage to display the FULL 
indication in 0.1 V steps. 
NEAR END 11.0 : 11.8 : 15.0
Set the NEAR END voltage in 0.1 V steps. 
END
11.0 : 11.1 : 15.0
When MANUAL is selected in the menu 
above, set the END voltage in 0.1 V steps. 
–CUF – 
						

							109
8
8-6-4 MIC/AUDIO1
8-6-5 MIC/AUDIO2
The ____ in the Adjustable Range column indicates the preset
mode.
Items/
Data Saved Adjustable 
Range Remarks 
FRONT VR CH1 FRONT
W. L .
REAR
ALL
OFFSelect whether or not to enable the FRONT 
AUDIO LEVEL control for the signal selected 
as the input signal to AUDIO CH1.
FRONT:Only enabled when FRONT is 
selected. 
W. L . :Only enabled when WIRELESS is 
selected. 
REAR:Only enabled when REAR is 
selected. 
ALL:Enabled for any input selected. 
OFF:Disabled for any input selected. 
Recording level does not change by 
turning the volume control.  –CUF –
FRONT VR CH2 FRONT
W. L .
REAR
ALL
OFFSelect whether or not to enable the FRONT 
AUDIO LEVEL control for the signal selected 
as an input signal to AUDIO CH2. 
FRONT:Only enabled when FRONT is 
selected. 
W. L . :Only enabled when WIRELESS is 
selected. 
REAR:Only enabled when REAR is 
selected. 
ALL:Enabled for any input selected. 
OFF:Disabled for any input selected. 
Recording level does not change by 
turning the volume control.  –CUF –
MIC LOWCUT 
CH1FRONT
REAR
W. L .
OFFSelect the microphone low-cut filter. 
–CUF –
MIC LOWCUT 
CH2FRONT
REAR
W. L .
OFFSelect the microphone low-cut filter. 
–CUF –
MIC LOWCUT 
CH3FRONT
REAR
W. L .
OFFSelect the microphone low-cut filter. 
vCUF –
MIC LOWCUT 
CH4FRONT
REAR
W. L .
OFFSelect the microphone low-cut filter. 
–CUF –
LIMITER CH1 ON
OFFSelect the limiter. 
–CUF –
LIMITER CH2 ON
OFFSelect the limiter. 
–CUF –
AU TO  L E VE L 
CH3ONOFFSelect the level setting method. 
–CUF –
AU TO  L E VE L 
CH4ONOFFSelect the level setting method. 
–CUF –
REC
CH3/CH4SWCH1/2Select the signals to be recorded in CH3 
and CH4. 
SW:According to camera’s CH3 and CH4 
selector switches. 
CH1/2:Record same signals as CH1 and 
CH2. 
–CUF –
25M REC CH 
SEL2CH4CHSelect the audio channels to be recorded in 
the DVCPRO and DV formats. 
2CH:Only recorded in CH1 and CH2. 
4CH:Recorded in all channels from CH1 
to CH4. 
–CUF –
Items/
Data Saved Adjustable 
Range Remarks
TEST TONE NORMALALWAYS
OFF
CHSELSelect the test signal. NORMAL:Output test tones to CH1/2 when 
the OUTPUT/AUTO KNEE 
selector switch is set to BARS and 
the AUDIO IN switch CH1 is set to 
FRONT. 
ALWAYS:Output test tones to CH1/2 when 
OUTPU/AUTO KNEE selector 
switch is set to BARS. 
OFF:Disable test tone output. 
CHSEL:Output test tone to the channels 
where the AUDIO IN switch CH1 
or CH2 is set to FRONT when 
OUTPUT/AUTO KNEE selector 
switch is set to BARS. The test 
tone is not output to CH3 and 
CH4.
–CUF –
Items/
Data Saved Adjustable 
Range Remarks
FRONT MIC 
POWERONOFFSelect the phantom power supply for the 
front microphone. 
–CUF –
REAR MIC 
POWERONOFFSelect the phantom power supply for the 
rear microphone. 
–CUF –
AUDIO OUT ONOFFSet the audio output circuit. 
OFF:Power-down output circuit to disable 
output. 
ON:Enable output. 
–CUF –
MONITOR 
SELECTSTEREOMIXSelect the signal format for the monitor 
output. 
–CUF –
FRONT MIC 
LEVEL–40dB–50dBSelect the front microphone input level. 
–CUF –
REAR MIC CH1 
LV L–50dB
–60dBSelect the rear microphone input level. 
–CUF –
REAR MIC CH2 
LV L–50dB
–60dBSelect the rear microphone input level. 
–CUF –
REAR LINE IN 
LV L0dB
+4dBSelect the rear line input level. 
–CUF –
AUDIO OUT LVL 0dB
+4dBSelect the audio output level. 
–CUF –
HEADROOM 18dB
20dBSet the headroom (standard level). 
–CUF –
WIRELESS 
WARNON
OFFSelect whether or not to enable the alarm to 
trigger for poor wireless receiver reception. 
–CUF – 
						

							110
8-6-6 TC/UB
8-6-7 UMID SET/INFO

Please refer to [4-5-6 Setting the UMID Information] for the
UMID information setting. 
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
TC MODE DFNDFSet the time code mode. 
DF: Drop frame. 
NDF: Non drop frame. 
–CUF –
UB MODE USERTIME
DAT E
EXT
TCG
FRM RATE
REGENSelect the user bits mode. 
USER:Select UB value set in the LCD 
section. 
TIME:Select local time (hours, minutes, 
seconds). 
DAT E:Select local date and time (2 last 
digits of year, month, date, time). 
EXT:Slaved to UB from TC-IN. If reading 
fails, USER value is retained. 
TCG:TCG value enters UB. 
FRM RATE:
Select same camera shoting 
information (frame rate, etc.) with the 
VAUX UB (VITC UB). 
REGEN:Read out value stored in the card 
and record value continuously. 
–CUF –
VITC UB MODE USER/EXT
TIME
DAT E
TCG
FRM RATE
REGEN
Select the user bits mode for VAUX TC 
(VITC). 
USER/EXT:
If UB MODE is set to EXT, the EXT 
value is recorded. If not, USER value 
set by UB is recorded. 
TIME:Select local time (hours, minutes, 
seconds). 
DAT E:Select local date and time (2 last 
digits of year, month, date, time). 
TCG:TCG value enters UB. 
FRM RATE:
Select same camera shoting 
information (frame rate, etc.) with the 
VAUX UB (VITC UB). 
REGEN:Read out value stored in card and 
record value continuously. 
–CUF –
TCG SET HOLD ON
OFFON/OFF switching for the feature that 
always starts recording (when the power is 
turned ON again) the TCG value that was 
set before the power is turned OFF. 
–CUF –
FIRST REC TC REGENPRESETFor the first recording after the power is 
turned on, a P2 card is inserted and then 
switching from this P2 card to another 
recording-target P2 card is performed, 
select whether or not to regenerate the time 
code as the value on the new P2 card.
REGEN:For clips recorded on the recording-
target P2 card, regenerate the time 
code as the time code of the clip that 
has the most recent date and time. 
PRESET:
Use the camera-recorder’s internal 
time code. 

Set the date and time accurately. For 
guidance on setting, see [4-5-2 Setting the 
Internal Clock’s Date and Time].
–CUF –
P. O F F  L C D  
DISPLAYONOFFSelect whether or not to display the time 
code setting and counter indication on the 
LCD monitor when the power is turned OFF. 
ON:Display setting and indication while 
the power is turned OFF. 
OFF:Power-down LCD monitor while 
camera power is turned OFF. Setting 
and indication disabled. 
–CUF –
Items/
Data Saved Adjustable 
Range Remarks
TC OUT TCGTCG/TCRSelect the time code to be output to the time 
code output connector. 
TCG:Always output time code generator 
value. 
TCG/TCR:
Display time code generator value in 
E-E mode, and time code reader 
value in V-V mode. 
–CUF –
TC DISP SEL 30F24FSelect the display format for the time code 
frame digits. 
30F:Display time code frame digits in 30 
frames. 
24F:Convert time code frame digits into 
24 frames for display. 
–CUF –
Items/
Data Saved Adjustable 
Range Remarks
COUNTRY NO-INFOInput the user’s country. NO-INFO is 
displayed until the input completes. 
–CUF –
ORGANIZATIONNO-INFOInput the user’s organisation or company 
name. NO-INFO is displayed until the input 
completes. 
–CUF –
USER NO-INFOInput the user name. NO-INFO is displayed 
until the input completes. 
–CUF –
DEVICE NODEIndicate the product ID number. 
–––––