Panasonic Aj Spx800p Operating Instructions Manual

							91
8
8-2 SYSTEM SETTING
8-2-1 SYSTEM MODE
8-2-2 OPTION MODE
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
REC SIGNAL CAMVIDEO
1394Select video input signals. 
CAM  Record the signal from the camera VIDEO:Record the signal from the 
GENLOCK IN terminal 
1394:Record the signal from the 1394 
input terminal (when the optional unit 
is attached. *To be supported in the 
near future.) 

zAfter the power has been turned OFF, this
setting defaults to CAM when the power is
turned ON again. 
zWith VIDEO selected, to synchronise this
camera-recorder to the video signal (VBS)
that is input to the GENLOCK IN terminal,
the GENLOCK item in [8-2-6 GENLOCK]
must be set to EXT.
–CUFE
CAMERA 
MODE60i30PSwitch the operating mode of the camera. 
60i: Camera operates in 60i mode. 
30P: Camera operates in 30P mode. 
SCUF E
V.RES (30P) INTRLCEPROG.Set the vertical resolution when the 30p 
mode is selected. 
INTRLCE:Lines are mixed. Natural images 
can be obtained. 
PROG. :Lines are not mixed. Complete 
progressive images can be 
obtained when images are edited 
after shooting. 

When PROG. is selected, images are 
recorded as progressive segmented frame 
images, which enables complete 
progressive editing. However, adding 
Vertical Detail (V.DTL) produces unnatural 
images. Therefore, we recommend using 
the camera with V.DTL set to 0. (Sufficient 
vertical response is maintained in the 
images after the progressive editing even 
when V.DTL is set to 0.) 
SCUF E
ASPECT 16:94:3Select the aspect ratio for recording. 
16:9:Record in  aspect ratio. 
4:3:Record in  aspect ratio. 
–CUFE
REC MODE 50M25M
DVSelect the recording mode. 
50M:Record in DVCPRO50 format. 
25M:Record in DVCPRO format. 
DV:Record in DV format. 
–CUFE
SET UP 0%7.5%ASwitch the setup. (When the DVCPRO50 or 
DVCPRO format is selected.) 
0%:Setup is switched to 0% for both the 
camera output and the recording. 
7.5%A:Setup is switched to 7.5% for the 
camera output and 0% for the 
recording. 
–CUFE
REC TALLY REDGREEN
CHARSelect the method of displaying the 
recording status of the camera-recorder 
when controlling the equipment connected 
to 1394 (scheduled to be supported soon). 
The recording status of the connected 
equipment is displayed by the red tally lamp 
on the camera-recorder.
RED:The red tally lamp lights up. 
GREEN:The green tally lamp lights up. CHAR:The VF displays [REC] in characters. 
–CUFE
Items/
Data Saved Adjustable 
Range Remarks
ACCESS LED ONOFFSelect whether or not to enable illumination 
of the P2 card access LEDs. 
ON:Enable the P2 card access LEDs to 
light up for card status indications. 
OFF:LEDs remain off. 
–CUFE
Items/
Data Saved Adjustable 
Range Remarks
P. O F F  G P S  
DATAHOLD
CLEARSelect whether or not to hold the UMID GPS 
position information while the power is 
turned off, thereby keeping this information 
as status data holding the previous value 
until the power is turned on again, which 
enables a new measurement to start. 
HOLD:Hold and save the data. CLEARClear the data when the power is 
turned off, and save zero (No-Info) 
from the next power-on until a new 
measurement is completed. 
–CUF –
SDI METADATA ONOFFSelect whether or not to output metadata 
(UMID) to the SDI (when the optional AJ-
YA902AG is attached). 
–CUF –
SDI EDH ONOFFSelect whether or not to add an error 
detection flag to the SDI output (when the 
optional AJ-YA902AG is attached). 
–CUF –
SAVE SW (AUD 
OUT)ON
OFFSelect whether or not to forcibly disable the 
audio output when the SAVE ON/OFF 
switch is set to [ON].
ON:Disable audio output. 
OFF:Enable audio output. 
–CUF –
SAVE SW (LCD) ONOFFSelect whether or not to automatically turn 
off the LCD monitor when the SAVE ON/
OFF switch is set to [ON].
ON:Turn off LCD monitor. 
OFF:Do not turn off LCD monitor. 
–CUF –
SAVE SW (SDI) ON
OFFSelect whether or not to automatically 
disable the SDI output when the SAVE ON/
OFF switch is set to [ON].
ON:Disable SDI output. 
OFF:Enable SDI output. 
–CUF – 
						

							92
8-2-3 REC FUNCTION 8-2-4 OUTPUT SEL
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
PRE REC TIME 0SEC : 15SEC
Set PRE RECORDING. 
0-15SEC:
Set the length of time that can be 
retrospectively recorded before the 
REC START button is pressed. 

The maximum selectable range is 8 seconds 
when the REC MODE in the  screen is set to 50M (DVCPRO50). 
–CUF –
LOOP REC 
MODEON
OFFSelect whether or not to enable LOOP REC. 
This setting can be used with PRE 
RECORDING features. 
ON: Enable LOOP REC. 
OFF: Disable LOOP REC. 

After the power is turned off, this item will 
default to OFF the next time the power is 
turned on. 
–––F–
VOICE MEMO 
RESERVONOFFSet the available memory space for voice 
memos in P2 cards. 
ON:Reserve a voice memo area of 10 
minutes or longer separately from the 
video recording capacity. The voice 
memo area can be used even when 
FULL is displayed for the recording 
capacity of the P2 card.
OFF:Do not reserve any voice memo 
space. 

Even when this item is set to OFF, and FULL 
is displayed for the P2 card’s recording 
capacity, it may be possible to record voice 
memos depending on the status of the P2 
card. 
–CUF –
REC START ALL
NORMALSelect operating modes that allow recording 
to star t. 
ALL:Allow recording to start during stop, 
recording pause, and playback. 
NORMAL:
  Allow recording to start during stop 
and recording pause. 
–CUF –
Items/
Data Saved Adjustable 
Range Remarks
VIDEO OUT 
SELVBSVF
Y
SDISelect the output signal on the VIDEO OUT 
terminal. 
VBS:Output a regular composite signal. 
VF:Output a VF Y signal. The status 
display is also superimposed. 
Y:Output a component Y signal. 
SDI:Output an SDI signal. Only 
selectable when the optional AJ-
YA902AG extension board is 
attached. 
–CUF –
OUTPUT CHAR TC
STATUS
MENU
ONLY
Set the character contents superimposed 
onto the output signals for the VIDEO OUT 
terminal (Analog or SDI) and MON OUT 
terminal. 
TC:Display the time code. (Displays the 
menu when menu characters are 
superimposed.)

The TC display position moves up and down 
depending on the camera ID position. 
STATUS:
Display the same characters 
superimposed on the VF signal. 
(Displays the menu when menu 
characters are superimposed.)
MENU ONLY:
Displays only when the menu 
characters are superimposed. No 
display appears when other 
characters are superimposed. 
–CUF –
MONITOR OUT 
CHARON
OFFSelect whether or not to superimpose 
characters on the MON OUT terminal signal 
independently of the camera’s VIDEO OUT 
CHARACTER switch. (The character 
content is the same as the video output 
signal.)
ON: Enable superimpose. 
OFF:Disable superimpose. 
–CUF –
LCD MON 
CHARONOFFSelect whether or not to superimpose 
characters on the LCD monitor. (The 
character content is the same as the video 
output signal.)
ON:Enable superimpose. 
(Not interlocked with the VIDEO OUT 
CHARACTER switch.)
OFF:Disable superimpose. 
(Not interlocked with the VIDEO OUT 
CHARACTER switch.)
–CUF –
VF MODE EE/PBEESelect the image to display in the viewfinder. EE/PB:Display the playback image in the 
playback mode. 
EE:Always display the camera image. 
–CUF –
THUMBNAIL 
OUTON
OFFSelect whether or not to output clip 
thumbnails displayed on the LCD monitor to 
the video output and monitor output signals. 
ON: Enable output. 
OFF: Disable output. 
–CUF – 
						

							93
8
8-2-5 LCD MONITOR
8-2-6 GENLOCK
8-3 PAINT
8-3-1 ROP
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
BRIGHTNESS –7 : +0 : +7
Adjust the LCD monitor brightness. 
–CUF –
COLOR LEVEL –7 : +0 : +7
Adjust the LCD monitor chroma level. 
–CUF –
CONTRAST –7 : +0 : +7
Adjust the LCD monitor contrast. 
–CUF –
BACKLIGHT HIGH
NORMALSelect whether or not to set the LCD monitor 
brightness to always high. 
HIGH:Set to always high. 
NORMAL:The brightness changes 
according to the BRIGHTNESS 
setting. 
–CUF –
SELF SHOOT NORMAL
MIRRORSelect whether or not to change the LCD 
monitor to mirror image. 
NORMAL: Do not change to mirror image. MIRROR: Change to mirror image. 
–CUF –
ASPECT CONV. LT.BOX
SQUEEZESelect a screen ratio for images displayed 
on the LCD monitor. 
LT. B O X:Display images in the letter box 
size. 
SQEEZE:Display images in the squeeze size. 

This item is enabled only when ASPECT 
described in “8-2-1 SYSTEM MODE” is set 
to16:9. –CUF –
Items/
Data Saved Adjustabl
e Range Remarks 
GENLOCK INTEXTSwitch the camera synchronising signal. 
INT:Synchronise with the internal 
reference signal regardless of the 
reference signal input to the 
GENLOCK IN terminal. 
EXT:Synchronise with the reference signal 
input to the GENLOCK IN terminal. 
–CUFE
H PHASE 
COARSE–50 : +00 : +50
Perform coarse phase adjustment for 
horizontal hold when configuring a system. 
–––––
H PHASE FINE –160 : +000 : +160
Perform fine phase adjustment for horizontal 
hold when configuring a system. 

This adjustment simultaneously shifts the SC 
phase. 
–––––
SC PHASE 
COARSE0
1
 : 3
Perform coarse SC PHASE adjustment when 
GENLOCK is set. 
–––––
SC PHASE 
FINE–75 : +00 : +75
Perform fine SC PHASE adjustment when 
GENLOCK is set. 

When adjusting GENLOCK, please adjust H 
PHASE first, and then adjust SC PHASE. 
–––––
Items/
Data Saved Adjustable 
Range Remarks
MASTER PED –200 : +020 : +200
Set the master pedestal level. 
SCUF E
MASTER DTL –31 : +00 : +31
Set the H Detail and V Detail levels.
SCUF E
MASTER 
GAMMA0.35 : 0.45 : 0.75
Set MASTER GAMMA in 0.01 steps. 
SCUF E
KNEE POINT 70.0% : 85 0% : 107.0%
Set the KNEE POINT position in 0.5% steps. 
SCUF E
KNEE SLOPE 0 : 50 : 99
Set the KNEE slope. 
SCUF E
R GAIN –200 : +000 : +200
Set the Rch gain. 
SCUF E
G GAIN –200 : +000 : +200
Set the Gch gain. 
SCUF E
B GAIN –200 : +000 : +200
Set the Bch gain. 
SCUF E
R PEDESTAL –100 : +000 : +100
Set the Rch pedestal level. 
SCUF E
G PEDESTAL –100 : +000 : +100
Set the Gch pedestal level. 
SCUF E
B PEDESTAL –100 : +000 : +100
Set the Bch pedestal level. 
SCUF E 
						

							94
8-3-2 MATRIX

The items indicated by „ are the setting items for PAINT MENU
SW(„) R/W in the  screen. The items
without „ are the setting items for PAINT MENU LEVEL R/W. 
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information. 
8-3-3 COLOR CORRECTION
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustabl
e Range Remarks 
„
MATRIX 
TABLEABSelect the color correction table. 2 types of 
tables can be stored: type A and type B.
SCUF E
MATRIX R-G –31 : +00 : +31
Adjust the tint. 
SCUF E
MATRIX R-B –31 : +00 : +31
Adjust the tint. 
SCUF E
MATRIX G-R –31 : +00 : +31
Adjust the tint. 
SCUF E
MATRIX G-B –31 : +00 : +31
Adjust the tint. 
SCUF E
MATRIX B-R –31 : +00 : +31
Adjust the tint. 
SCUF E
MATRIX B-G –31 : +00 : +31
Adjust the tint. 
SCUF E
„
MATRIX 
TABLEOFF
A
B
Select the color correction table to be applied 
to the selected GAIN switch (L/M/H). 
SCUF E
Items/
Data Saved Adjustable 
Range Remarks
R
(SAT/PHASE)–63 : +00 : +63
Perform red color correction (saturation and 
hue). 
SCUF E
R-Mg
(SAT/PHASE)–63 : +00 : +63
Perform color correction (saturation and 
hue) between red and magenta. 
SCUF E
Mg
(SAT/PHASE)–63 : +00 : +63
Perform magenta color correction 
(saturation and hue). 
SCUF E
Mg-B
(SAT/PHASE)–63 : +00 : +63
Perform color correction (saturation and 
hue) between magenta and blue. 
SCUF E
B
(SAT/PHASE)–63 : +00 : +63
Perform blue color correction (saturation and 
hue). 
SCUF E
B-Cy
(SAT/PHASE)–63 : +00 : +63
Perform color correction (saturation and 
hue) between blue and cyan. 
SCUF E
Cy
(SAT/PHASE)–63 : +00 : +63
Perform cyan color correction (saturation 
and hue). 
SCUF E
Cy-G
(SAT/PHASE)–63 : +00 : +63
Perform color correction (saturation and 
hue) between cyan and green. 
SCUF E
G
(SAT/PHASE)–63 : +00 : +63
Perform green color correction (saturation, 
hue). 
SCUF E
G-Yl
(SAT/PHASE)–63 : +00 : +63
Perform color correction (saturation, hue) 
between green and yellow. 
SCUF E
Yl
(SAT/PHASE)–63 : +00 : +63
Perform yellow color correction (saturation, 
hue). 
SCUF E
Yl-R
(SAT/PHASE)–63 : +00 : +63
Perform color correction (saturation, hue) 
between yellow and red. 
SCUF E
„
COLOR 
CORRECTON
OFFSelect whether or not to enable color 
correction for the selected GAIN switch (L/
M/H).
ON: Enable correction. 
OFF: Disable correction. 
SCUF E 
						

							95
8
8-3-4 LOW SETTING 8-3-5 MID SETTING

The items indicated by „ are the setting items for PAINT MENU
SW(„) R/W in the  screen. The items
without „ are the setting items for PAINT MENU LEVEL R/W. 
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information. 
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
„
MASTER 
GAIN–3dB : 0dB : 30dB
Select the master gain from –3, 0, 3, 6, 9, 
12, 15, 18, 21, 24, 27, or 30dB. 
SCUF E
H.DTL LEVEL 00 : 17 : 63
Set H.DTL LEVEL. 
SCUF E
V.DTL LEVEL 00 : 24 : 31
Set V.DTL LEVEL. 
SCUF E
DTL CORING 00 : 02 : 15
Set DTL CORING. 
SCUF E
H.DTL FREQ. 00 : 20 : 31
Set a frequency (DTL width) at which H.DTL 
is added. The greater the value, the higher 
the frequency (the narrower the DTL).
SCUF E
LEVEL 
DEPEND.0
1
 : 5
Set LEVEL DEPEND. 
No DTL is added to the portion whose 
brightness is the setting value or less. 
When the GAMMA MODE SEL item is set to 
STD, each setting value represents 
brightness levels, as follows: 0 = about 0%, 
1 = about 4%, 2 = about 8%, 3 = about 12%, 
4 = about 16%, 5 = about 20%.
SCUF E
MASTER 
GAMMA0.35 : 0.45 : 0.75
Set MASTER GAMMA in 0.01 steps. 
SCUF E
BLACK 
STRETCH–3 : OFF : +3
Set the gamma curb for dark spots. 
SCUF E
„
MATRIX 
TABLEOFF
A
B
Select the color correction table. 
SCUF E
„
COLOR 
CORRECTON
OFFSet the color correction to ON or OFF. 
SCUF E
Items/
Data Saved Adjustable 
Range Remarks
„
MASTER 
GAIN–3dB : 9dB : 30dB
Select the master gain from –3, 0, 3, 6, 9, 
12, 15, 18, 21, 24, 27, or 30dB. 
SCUF E
H.DTL LEVEL 00 : 14 : 63
Set H.DTL LEVEL. 
SCUF E
V.DTL LEVEL 00 : 20 : 31
Set V.DTL LEVEL. 
SCUF E
DTL CORING 00 : 03 : 15
Set DTL CORING. 
SCUF E
H.DTL FREQ. 00 : 20 : 31
Set a frequency (DTL width) at which H.DTL 
is added. The greater the value, the higher 
the frequency (the narrower the DTL).
SCUF E
LEVEL 
DEPEND.)0
1
 : 5
Set LEVEL DEPEND. 
No DTL is added to the portion whose 
brightness is the setting value or less. 
When the GAMMA MODE SEL item is set to 
STD, each setting value represents 
brightness levels, as follows: 0 = about 0%, 
1 = about 4%, 2 = about 8%, 3 = about 12%, 
4 = about 16%, 5 = about 20%.
SCUF E
MASTER 
GAMMA0.35 : 0.45 : 0.75
Set MASTER GAMMA in 0.01 steps. 
SCUF E
BLACK 
STRETCH–3 : OFF : +3
Set the gamma curb for dark spots. 
SCUF E
„
MATRIX 
TA B L EOFF
A
B
Select the color correction table. 
SCUF E
„
COLOR 
CORRECTON
OFFSet the color correction to ON or OFF. 
SCUF E 
						

							96
8-3-6 HIGH SETTING 8-3-7 ADDITIONAL DTL

The items indicated by „ are the setting items for PAINT MENU
SW(„) R/W in the  screen. The items
without „ are the setting items for PAINT MENU LEVEL R/W. 
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information. 
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
„
MASTER 
GAIN–3dB : 18dB : 30dB
Select the master gain from –3, 0, 3, 6, 9, 
12, 15, 18, 21, 24, 27, or 30dB. 
SCUF E
H.DTL LEVEL 00 : 12 : 63
Set H.DTL. 
SCUF E
V.DTL LEVEL 00 : 17 : 31
Set V.DTL LEVEL. 
SCUF E
DTL CORING 00 : 08 : 15
Set DTL CORING. 
SCUF E
H.DTL FREQ. 00 : 20 : 31
Set a frequency (DTL width) at which H.DTL 
is added. The greater the value, the higher 
the frequency (the narrower the DTL).
SCUF E
LEVEL 
DEPEND.)0:3 : 5
Set LEVEL DEPEND. 
No DTL is added to the portion whose 
brightness is the setting value or less. 
When the GAMMA MODE SEL item is set to 
STD, each setting value represents 
brightness levels, as follows: 0 = about 0%, 
1 = about 4%, 2 = about 8%, 3 = about 12%, 
4 = about 16%, 5 = about 20%.
SCUF E
MASTER 
GAMMA0.35 : 0.55 : 0.75
Set MASTER GAMMA in 0.01 steps. 
SCUF E
BLACK 
STRETCH–3 : OFF : +3
Set the gamma curb for dark spots. 
SCUF E
„
MATRIX 
TABLEOFF
A
B
Select the color correction table. 
SCUF E
„
COLOR 
CORRECTON
OFFSet the color correction to ON or OFF. 
SCUF E
Items/
Data Saved Adjustable 
Range Remarks
KNEE APE LVL OFF
1
2
 : 5
Set KNEE APE LEVEL. 
SCUF E
CHROMA DTL OFF
0
 : 5
Set the chroma detail. 
Detects the chroma edge and superimposes 
it on Y to enhance H.DTL. A greater value 
increases the correction. 
SCUF E
DTL GAIN(+) –31 : +00 : +31
Adjust the detail level toward + (upwards). 
SCUF E
DTL GAIN(–) –31 : +00 : +31
Adjust the detail level toward the – 
(downwards). 
SCUF E
DTL CLIP 00 : 63
Adjust the detail signal clip towards the + 
direction. 
SCUF E
DTL SOURCE (R+G)/2(G+B)/2
2G+R+B /4
(3G+R)/4
R
GSet the signal source for detail signal 
components. 
SCUF E
H.DTL LINE MIX 1H2HSet the scan line to generate the H.DTL 
signal. 
SCUF E
„
CORNER DTL ONOFFON/OFF switching for CORNER DTL mode, 
which enhances the resolution around the 
screen perimeter. 
SCUF E 
						

							97
8
8-3-8 SKIN TONE DTL 8-3-9 KNEE/LEVEL

The items indicated by „ are the setting items for PAINT MENU
SW(„) R/W in the  screen. The items
without „ are the setting items for PAINT MENU LEVEL R/W. 
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information. 
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
„
SKIN TONE 
DTLON
OFFSet the skin tone DTL to ON or OFF. 
SCUF E
„
SKIN TONE 
ZEBRAON
OFFON/OFF switching for ZEBRA within the 
SKIN TONE range. 
SCUF E
SKIN DTL 
CORING0 : 5 : 7
Adjust the effect of SKIN TONE DTC 
CORING. 
SCUF E
SKIN TONE 
GETUsed when obtaining the target hue for 
SKIN TONE DTL. Align the center marker 
and the target object with each other.
–––––
Y MAX 000 : 190 : 255
Set the maximum value of the brightness 
signal to which SKIN TONE effect is 
enabled. 
SCUF E
Y MIN 000 : 010 : 255
Set the minimum value of the brightness 
signal to which the SKIN TONE effect is 
enabled. 
SCUF E
I CENTER 000 : 022 : 255
Set the center position on the I axis (the 
area where SKIN TONE is enabled). 
SCUF E
I WIDTH 000 : 010 : 255
Set the area width where SKIN TONE is 
enabled along the I axis above and below 
the I CENTER. 
SCUF E
Q WIDTH 000 : 005 : 255
Set the area width where SKIN TONE is 
enabled along the Q axis above and below 
the I CENTER. 
SCUF E
Q PHASE –128 : +000 : +127
Set the phase in the area where SKIN TONE 
is enabled based on the Q axis. 
SCUF E
R-Y
B-Y
Q-WIDTHI-WIDTH
Q-PHASE I-CENTER
Y
Y-MAX
Y-MIN
0
+ direction
– direction
 = SKIN TONE AREAItems/
Data Saved Adjustable 
Range Remarks
MASTER PED –200 : +020 : +200
Set the master pedestal. 
SCUF E
„
MANUAL 
KNEEONOFFSet the mode when the AUTO KNEE switch 
is OFF. The KNEE POINT/SLOPE set value 
is enabled when this setting is ON. 
SCUF E
KNEE POINT 70.0% : 85.0% : 107.0%
Set the KNEE POINT position in 0.5% steps. 
SCUF E
KNEE SLOPE 00 : 50 : 99 (98)
Set the KNEE SLOPE. 
0 setting is equal to KNEE OFF. 

The adjustable range when using the AJ-
EC3P is from 00 to 98. 
SCUF E
„
WHITE CLIP ONOFFSet the WHITE CLIP feature to ON or OFF. 
The WHITE CLIP LVL set value is enabled 
when this setting is ON. 
SCUF E
WHITE CLIP 
LV L90% : 105% : 109%
Set WHITE CLIP LEVEL. 
SCUF E
A.KNEE POINT 80% : 85% : 107%
Set the AUTO KNEE POINT position in 
0.5% steps. This setting is enabled when the 
OUTPUT/AUTO KNEE selector switch is set 
to CAM.AUTO KNEE ON. 
SCUF E
A.KNEE LVL 100 : 105 : 109
Set the AUTO KNEE LEVEL. 
SCUF E
A.KNEE 
RESPONSE1 : 4
Set the AUTO KNEE response speed. 
The smaller the setting value, the faster the 
response speed.
SCUF E 
						

							98
8-3-10 GAMMA
8-3-11 FLARE8-3-12„CAMERA SETTING
ZEBRA Pattern Display

All items in CAMERA SETTING are setting targets of the item
PAINT MENU SW(„) R/W in the 
screen. 
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
MASTER 
GAMMA0.35 : 0.45 : 0.75
Set the master gamma in 0.01% steps. 
SCUF E
R GAMMA –15 : +00 : +15
Set the Rch gamma. 
SCUF E
B GAMMA –15 : +00 : +15
Set the Bch gamma. 
SCUF E
GAMMA MODE 
SELSTDNEWS
FILM LIKE1
FILM LIKE2Select the gamma. 
STD:Standard gamma feature.
This video gamma feature can 
effectively reproduce gradations by 
reducing whiteouts and blackouts 
when shooting an object with 
partially highlighted areas. This 
gamma is especially effective in the 
AU TO KN E E mo d e. 
FILM LIKE1:
Cinema gamma feature for video. 
This gamma is set with scene file 4 
as the factory setting. 
FILM LIKE2:
Cinema gamma feature for video. 
This gamma feature can reproduce 
gradations in highlighted areas better 
than FILM LIKE1 gamma. 

zSelecting NEWS gamma disables
settings under the items KNEE SLOPE,
KNEE POINT, and A.KNEE POINT
outlined in [8-3-9 KNEE/LEVEL]. These
settings are also disabled when NEWS
gamma is selected with the USER switch. 
zWhen FILELIKE1 or FILELIKE2 is
selected, little change occurs and a
certain curve is maintained when the
setting value for the KNEE SLOPE item in
[8-3-9 KNEE/LEVEL] is 00 to 50. 
SCUF E
Items/
Data Saved Adjustabl
e Range Remarks 
R FLARE 000 : 100
Set the R FLARE. 
SCUF E
G FLARE 000 : 100
Set the G FLARE. 
SCUF E
B GAMMA 000 : 100
Set the B FLARE. 
SCUF E
Items/
Data Saved Adjustable 
Range Remarks
DETAIL ONOFFSet the DTL (H, V) to ON or OFF. 
SCUF E
2D LPF ON
OFFON/OFF switching for the two-dimensional 
LPF that reduces cross-color. 
SCUF E
HIGH COLOR ON
OFFON/OFF switching for the HIGH COLOR 
mode, which enhances the color dynamic 
range. 
SCUF E
GAMMA ONOFFSet the gamma circuit to ON or OFF. 
SCUF E
TEST SAW ON
OFFSwitch the test signal ON or OFF. 
SCUF E
FLARE ONOFFSet the flare correction to ON or OFF. 
SCUF E
H-F COMPE. ONOFFON/OFF switching for the H-F COMPE 
mode, which enhances the DTL in the high-
frequency range. 
SCUF E
SPOT OFF ON
109%
0% ZEBRA 2
DETECTZEBRA 2
ZEBRA 1
DETECTVideo Level 
						

							99
8
8-4 VF
8-4-1 VF DISPLAY 8-4-2 VF MARKER
8-4-3 USER BOX
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
DISP 
CONDITIONNORMALHOLDNORMAL:Display status constantly. 
HOLD:Display status only when the 
MODE CHECK switch is pressed. 
–CUFE
DISP MODE 1
2
3Set the DISP MODE. 
Switch the camera’s Warning/Message 
indication. Please refer to [4-7-4 Display 
Modes and Setting Changes/adjustment 
Result Messages] for more information. 
–CUFE
VF OUT YNAM
R
G
BSelect the VF output. 
Y:Brightness signal
NAM:Output signal with the highest level 
among R, G, and B signals. 
R:Rch signal
G:Gch signal
B:Bch signal
–CUFE
VF DTL 0 : 3 : 5
Select the VF DTL. 
Additionally enhance the DTL for the VF 
signal. 0 setting is the same DTL as the 
primary scan lines. 
–CUFE
ZEBRA1 
DETECT0% : 70% : 109%
Set the ZEBRA1 detection level (IRE value). 
–CUFE
ZEBRA2 
DETECT0% : 85% : 109%
Set the ZEBRA2 detection level (IRE value). 
–CUFE
ZEBRA2 ON
SPOT
OFF
Set the ZEBRA2 to ON, OFF, or SPOT. 
–CUFE
LOW LIGHT LVL OFF
10%
15%
20%
25%
30%
35%Set the camera incoming light volume at 
which to display LOW LIGNT. 
–CUFE
ECU MENU 
DISP.ON
OFFSet the menu display on the VF to ON or 
OFF when the ECU is connected. 
–CUFE
50M 
INDICATORON
OFFSet the 50M recording indication to ON or 
OFF. 
–CUFE
MARKER/CHAR 
LV L50%60%
70%
80%
90%
100%Adjust the brightness of markers and 
characters displayed on the VF. 
–CUFE
Items/
Data Saved Adjustable 
Range Remarks
TA B L E ABSelect the VF MARKER setting table. 
First, select table A or B, then set the items 
below for each table. 
–CUFE
CENTER MARK OFF
1
2
3
4
Switch the center mark. 
OFF:Do not display center mark. 
1:+ (large)
2:Hollow (large)
3:+ (small)
4:Hollow (small)
–CUFE
SAFETY ZONE OFF
1
2
Select the frame type for the safety zone. 
OFF:Do not display frame. 
1:Box
2:Corner frame
–CUFE
SAFETY AREA 80% : 90% : 100%
Set the position of the safety zone. 
–CUFE
FRAME SIG 4:313:9
14:9
VISTASet the frame marker. 
Only enabled when REC MODE is set to 
16:9. 
The VISTA ratio is 16:8.65. 
–CUFE
FRAME MARK ON
OFFSet the frame marker to ON or OFF. 
–CUFE
FRAME LVL 0 : 15
Set the level outside the frame marker. 
0:Equivalent to signal OFF. 
15:Same brightness as center area. 
This setting, however, is disabled if 
the FRAME SIG is set to VISTA. 
–CUFE
Items/
Data Saved Adjustable 
Range Remarks
USER BOX ON
OFFSelect whether or not to display the USER 
BOX. 
–CUFE
USER BOX 
WIDTH1 : 13 : 100
Set the width of the USER BOX. 
–CUFE
USER BOX 
HEIGHT1 : 13 : 121
Set the height of the USER BOX. 
–CUFE
USER BOX H 
POS–50 : +00 : +50
Set the horizontal position of the USER 
BOX. 
–CUFE
USER BOX V 
POS–121 : +000 : +121
Set the vertical position of the USER BOX. 
–CUFE 
						

							100
8-4-4 VF INDICATOR1 8-4-5 VF INDICATOR2
The ____ in the Adjustable Range column indicates the preset
mode. 
Items/
Data Saved Adjustable 
Range Remarks 
EXTENDER ONOFFSet the extender indication to ON or OFF. 
–CUFE
SHUTTER ONOFFSet the shutter speed indication to ON or 
OFF. 
–CUFE
FILTER ONOFFSet the filter No. indication to ON or OFF. 
–CUFE
WHITE ONOFFSet the AWB PRE/A/B indication to ON or 
OFF. 
–CUFE
GAIN ONOFFSet to ON or OFF the indications for current 
gain setting, S.GAIN, and DS.GAIN. 
–CUFE
IRIS OFF
IRIS
S+IRIS
S
OFF:Disable indications of both the super 
iris ON status and the iris value. 
IRIS:Enable only the iris value indication. 
S+IRIS:Enables indications of the super iris 
ON status and the iris value. 
S:Enable indication of the super iris ON 
status. 
(The iris value indication and the iris 
override indication/non indication are 
interlocked.) –CUFE
CAMERA ID BARCAM
ALWAYS
OFFSelect when to enable the ID mix during 
recording. 
BAR:Enable when recording color bars. 
CAM:Enable when recording camera 
image. 
ALWAYS:Enable always. 
OFF:Disable ID mix. 
–CUFE
ID POSITION UPPER R
UPPER L
LOWER R
LOWER L
Set the camera ID recording position. UPPER R:Upper right. UPPER L:Upper left. LOWER R:Lower right. LOWER L:Lower left. 
–CUFE
DATE/TIME ON
OFFSelect whether or not to simultaneously mix 
the year/month/date and hour/minute/
second when recording the camera ID. 
–CUFE
ZOOM LVL ONOFFSet the zoom position indication to ON or 
OFF. 
–CUFE
COLOR TEMP ONOFFSet the color temperature indication to ON 
or OFF. 
–CUFE
CAMERA 
MODEONOFFSet the camera operation mode indication to 
ON or OFF. 
–CUFE
Items/
Data Saved Adjustable 
Range Remarks
P2CARD 
REMAINTOTA LONE-CARD
OFFSelect the indication mode for the P2 card’s 
remaining capacity. 
TOTAL:Display the total remaining capacity 
of all P2 cards in slots. 
ONE-CARD:
Display the remaining capacity of the 
P2 card currently used for recording. 
OFF:Disable the remaining capacity 
indication. 
–CUFE
BATTERY ONOFFSet the battery voltage indication to ON or 
OFF. 
–CUFE
AUD IO LVL ONOFFSet the audio lever meter indication to ON or 
OFF. 
–CUFE
TC TCG
TCR
TCG/TCR
OFFSelect the time code to display. 
TCG:Display the time code generator 
value in E-E mode. 
TCR:Display the time code reader value in 
V-V mode. 
TCG/TCR:
Display the time code generator 
value in E-E mode, and the time 
code reader value in V-V mode. 
OFF:Disable the time code display. 
–CUFE
SYSTEM INFO ALWAYS
NORMAL
OFF
Select the method of displaying system 
information and warnings.
ALWAYS:
Always display warnings.
NORMAL:
Display warnings for 3 seconds only 
when problems occur. 
OFF:Display no warnings other than 
“TURN POWER OFF”. –CUFE
SAVE LED P2CARD
SAVESet the SAVE lamp function. 
P2CARD:
The lamp blinks in synch with the 
warning message when the P2 
card’s remaining recording capacity 
is getting low. 
SAVE:The lamp lights up when the SAVE 
ON/OFF switch is set to ON and the 
output system assigned in [8-2-2 
OPTION MODE] is in the save mode.
–CUFE
DV O NOFFDV Select whether or not to enable DV 
indication when the format is set to DV. 
ON:Enable DV indication. 
OFF:Disable DV indication. 
–CUFE
VOICEMEMO ONOFFSelect whether or not to enable the   
indication during voice memo recording. 
ON:Enable DV indication. 
OFF:Disable DV indication. 
–CUFEV