Panasonic Aj Sd930b Operating Instructions Manual

51
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item DescriptionNo./Item Description
735
MON AUTO
SELAlthough CUE is automatically output to the
monitor output in accordance with the
operation mode when a setting AUTO has
been selected by setup menu item No. 721
(MONI CH SEL), the MON AUTO SEL setup
menu item is used to select the monitor
channel which is to be automatically switched
to CUE.
0000L/R:
CUE is output to both the left and right
channels.
0001 L:
CUE is output...

52
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
800
ADD LINE 25
00
REC LINE1 Sub-screenFor selecting the mode for recording signals
on additional lines.
0000 OFF:No signals are recorded on
additional lines.
0001 YC422:The 422 mode signals are
recorded on 1 line.
0002YC411:The 411 mode signals are
recorded on 1 line.
0003 Y1_B/W:Only the Y signal is recorded on
1 line directly.
0004 Y1_BPF:Only the Y signal is recorded on
1 line after it has been...

53
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item DescriptionNo./Item Description
Sub-screen801
ADD LINE 50
00
REC LINE1 Sub-screenFor selecting the mode for recording signals
on additional lines.
0000 OFF:No signals are recorded on
additional lines.
0001YC422:The 422 mode signals are
recorded on 2 lines.
0002 Y4_B/W:Only the Y signal is recorded on
4 lines directly.
0003 Y4_BPF:Only the Y signal is recorded on
4 lines after it has been
separated from the C signal....

54
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
803
TELETEXT
DET
[525i system]
00
REC LINE1
:
12
REC LINE13
[625i system]
00
REC LINE1
:
14
REC LINE15
SD955B
Sub-screenFor selecting the method used to detect the
lines in which the teletext signals are to be
recorded.
0000OFF:
The teletext signals are not recorded.
0001 AUTO:
The teletext signals are automatically detected
and recorded.
0002 MANU:
The lines in which the teletext signals are to be
recorded...

55
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
A00
LOADThis selects the user file whose contents will
be loaded into USER1.
0000USER2:The USER2 file contents are
loaded.
0001 USER3:The USER3 file contents are
loaded.
0002 USER4:The USER4 file contents are
loaded.
0003 USER5:The USER5 file contents are
loaded.

When the SET button is pressed after loading,
the setting will be stored in the memory. When
the MENU button is pressed, the setting will not
be...

56
Time code/user bit
Time code
The time code is used when the time code signal
generated by the time code generator (time code
signal generator) is to be recorded on the tape, its
values are to be read by the time code reader (time
code signal reader), and the absolute position of the
tape is to be displayed in increments of hours,
minutes, seconds and frames.
The time code is written in the sub-code area (data
area) of the helical track. This enables insert editing to
be conducted independently using...

57
Time code/user bit
Setting the external time code
1Set the VTR to stop mode.
3Set the TCG switch to EXT. (External time code
selection)
4The following settings can be selected with setup
menu No. 505 (EXT TC SEL).
LTC:
The LTC signal input to the TIME CODE IN
connector (XLR) on the rear panel is recorded
as TC.

LTC must be synchronized with the video signal.
VITC:
The VITC of the input video signal is recorded
as TC.
2Select “TC” using the COUNTER button.
Reproducing the time code/user bit
1Set the...

58
Display position
The position of the characters superimposed on the
display can be changed using setup menus No. 009
(CHARA H-POS) and No. 010 (CHARA V-POS).
Superimpose screen
The control signals, time code, etc. are displayed
using abbreviations.Characters displayed
The background of characters superimposed on the
display can be changed using setup menu No. 011
(CHARA TYPE).
TCR  
22: 
22: 
22: 
22
TV monitorT TC
CR
R  
2 22
2: : 
2 22
2: : 
2 22
2: : 
2 22
2
TV monitor
TCR  
22: 
22: 
22: 
22
TV...

59
Video output signals and servo reference signal
This section explains how the output signals and
servo reference signal are selected.
External synchronization of video
output signals
The video output signals are output in synchronization
with the REF VIDEO input signal or video input signal.
As shown in the figure below, this signal is selected in
accordance with the setup menu settings, VTR mode
and availability of the video input signal.
Synchronization is determined as follows depending
on the...

60
Video output signals and servo reference signal
Servo reference signal
The REF VIDEO input signal or video input signal is
selected as the servo reference signal.
As shown in the figure below, the signal is selected in
accordance with the setup menu settings, VTR mode
and availability of the video input signal.
Synchronization is determined as follows depending
on the availability of the REF VIDEO input signal
when “BB”, “CB100” or “CB75” has been selected as
the setup menu No. 600 (INT SG) setting....