Panasonic Aj Sd930b Operating Instructions Manual

41
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
320
VAR FWD
MAXThis sets the maximum SLOW FWD speed.
0000+4.1:+4.1 (+3.1)aspeed0001 +1.85:+1.85aspeed0002 +1:+1aspeed

OThe value for the DV/DVCAM tape is shown in
parenthesis (    ).
OAt any speed setting other than +4.1, the
phase cannot be synchronized from the editing
controller.
323
JOG FWD
MAXThis sets the maximum JOG FWD speed.
0000 +4.1:+4.1 (+3.1)aspeed0001 +1.85:+1.85aspeed0002+1:+1aspeed

OThe...

42
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
400
STILL TIMERThis selects the time to be taken until the unit
goes into the tape protection mode when it is
left standing in the stop or search still
(JOG/SLOW/SHTL) mode. 
(Unit: s = second, min = minute)
0000 0.5s
0001 5s
0002 10s
0003 20s
0004 30s
0005 40s
0006 50s
0007 1min
0008
2min
401
SRC
PROTECTWhen the time selected as the setup menu
item No. 400 (STILL TIMER) setting elapses
while the unit is in...

43
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
506
BINARY GPThis sets the usage status of the user bit of
the time code generated by the TCG.
0000000:
NOT SPECIFIED (character set not specified)
0001 001:
ISO CHARACTER (8 bits character set based
on ISO646, ISO2022)
0002 010:UNASSIGNED 1 (undefined)0003 011:UNASSIGNED 2 (undefined)0004 100:UNASSIGNED 3 (undefined)0005 101:PAGE/LINE0006 110:UNASSIGNED 4 (undefined)0007 111:UNASSIGNED 5 (undefined)
507...

44
511
VITC OUTThis selects how the VITC which is to be
superimposed onto the output video signal is
to be output.
0000SBC:
During recording:
The input time code, which was selected by
the setup menu No. 505 (EXT TC SEL)
setting and TCG switch, is output as the
VITC.
During playback:
The time code recorded in the SBC area is
output as the VITC.
0001 VAUX:
During recording:
The time code detected from the input video
signal is output as the VITC.
During playback:
The time code recorded in the VAUX area...

45
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item DescriptionNo./Item Description
600
INT SGThis selects the internal reference signal.
0001 BB:
The black burst is generated.
0002 CB100:
100% color bars are generated.
0003CB75:
75% color bars are generated.
601
OUT VSYNCThis selects whether to float the vertical sync
position of the video output in order to align
the video output phase with the input in the
EE/record/edit modes.
0000N-VF:Signals are not floated.0001...

46
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item DescriptionNo./Item Description
621
CCR MODEThis selects the cross color processing
during playback.
0000 OFF:
The cross color is output with no changes
made.
0001 ON:
The cross color can be reduced.

This setup menu is not displayed in the 625i
system.622
SETUP 25For setting 7.5% setup processing to be
performed on input and output signals in the
DVCPRO (25 Mbps) mode.
When the STOP button is pressed, operation is...

47
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
623
SETUP 50For setting 7.5% setup processing to be
performed on input and output signals in the
DVCPRO50 (50 Mbps) mode.
When the STOP button is pressed, operation is
transferred to the sub-screen, and the setup level
is set for each output. To return from the sub-
screen, press the STOP button again.

This setup menu is not displayed in the 625i
system.
00
CMPST IN Sub-screen
This selects the 7.5% setup...

48
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item Description
661
UMID GENThis selects the basic UMID information to be
recorded on the tape when ON has been
selected as the setup menu item No. 660
(UMID REC) setting.
0000 INT:
Newly created basic UMID information of this
unit is always recorded.
0001EXT:
The basic UMID information of the input
signals is recorded.
Newly created basic UMID information of this
unit is recorded if there is no basic UMID
information on...

49
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item DescriptionNo./Item Description
701
CH1 IN LVThis selects the audio input (CH1) reference
level switching.
0000 4dB
00010dB0002–20dB
702
CH2 IN LVThis selects the audio input (CH2) reference
level switching.
0000 4dB
00010dB0002–20dB
703
CH3 IN LVThis selects the audio input (CH3) reference
level switching.
0000 4dB
0001
0dB0002–20dB
704
CH4 IN LVThis selects the audio input (CH4) reference
level switching.
0000 4dB...

50
Setup menus
The underlined items indicates the initial setting.
USER menu
No./Item DescriptionNo./Item Description
721
MONI CH SELThis selects  the monitor output.
0000 MANU:
The output signal is as selected in MONITOR
SELECT buttons.
0001AUTO:
PCM AUDIO output is selected within the
–0.43 (–0.5)ato +1aspeed range; CUE is
automatically selected for all other tape
speeds.

The value for the DV/DVCAM tape is shown in
parenthesis (    ).
0002 PCM:
The PCM AUDIO signal is output over the
–10ato...