Panasonic Aj Pcs060g Operating Instructions Manual

E-10
ENGLISH

Control reference guide
Front
POWER button
Use this button to turn the unit ON and OFF.
When the unit is OFF, simply press the
[POWER] button to turn it ON. When ON, hold
the [POWER] button for at least two seconds
to turn it OFF.
POWER LED
Lights when the unit is ON. 
The POWER LED flashes during startup or
shutdown.
P2C button
Press to format P2 cards. After copying data to
the HDD, you can format the P2 card as
needed. (See page E-17)
Note: Data cannot be recovered after formatting....

E-11

Control reference guide (continued)
To p
START button
Press to start copying or formatting. 
Hold the [START] button for  at least 2 seconds
to start either process.
CANCEL button 
Press to cancel copying. 
During copying, hold the [CANCEL] button for  at
least 2 secondsto cancel copying. 
Sliding knob 
To open the front panel cover, slide the knob in
the direction of the arrow. 
Battery level indicator button
[]
After this button is pressed, the remaining power
level of the battery pack will be...

E-12
ENGLISH
Control reference guide (continued)
Left side

Back

Sliding switch cover
Sliding switch 
Slide toward the front to enable software
updates.
Normally, keep the switch toward the back. 
(See page E-28)
Power inlet
Insert an optional battery pack or AC adapter
here.
DC IN socket (7.9 V) 
Battery lock release button
When removing optional battery packs or AC
adapters, hold down the button as you slide it
toward the button side. 

VERIFY switch 
Use this switch to verify data after it has been...

E-13
Copying
When inserting a P2 card in the card slot, always hold the
card level and insert it carefully. Forcing cards in the slot at an angle may damage them
or the unit.
Do not eject P2 cards during access by the unit (when the [P2C] LED is \
lit). The data may be
lost or the P2 card damaged.  
Use an optional battery pack or AC adapter as the power source. (See page E-7)
In either case, make sure the power source is firmly connected to the un\
it. 
For connection instructions, refer to the...

E-14
ENGLISH
Capacity
(No. of cards that  can be copied) 
Write-protect switch settings
Data cannot be written to or deleted from
the card.
 Data may be written to or deleted from
the card. 

PROTECT

PROTECT

Copying (continued)
Up to 15 P2 cards worth of data can be copied to the unit's internal HDD\
. (However, in the case
of 8 GB P2 cards, the data on only 7 P2 cards can be copied.) To see ho\
w much space is
available on the HDD (how many cards can be copied), press the [HDD CA\
P] button...

E-15
Copying (continued)
When using an optional battery pack, you can check the remaining level. \
You can see how much
power is left by pressing the [ ] button and checking the [REMAIN] indicator. See²Battery
level ³, below.

Copy operations are not allowed when a low-voltage error occurs (when t\
he [ERROR] LED
lights in red and [E2] in [REMAIN] flashes in red). Use the battery pac\
k only if [E1] in [REMAIN]
is lit in green.
Once the level reaches 0 (zero), an error is displayed as described in\...

E-16
ENGLISH
Copying (continued)
: LED lit,, : LED flashing
G: greenOR : orange

4. Make sure all the [COPY STATUS] LEDs are lit in green
5. Press the [POWER] buttonCopying is complete and the [COPY STATUS] LEDs go out.
Note:• Once the data on a P2 card has been copied to the HDD, it cannot be copi\
ed to the HDD again. If this is
the case, one of the following operations will be performed depending on\
 the [VERIFY] switch setting. [VERIFY] switch is OFF:  Even when step 3 is taken, 100% is immediately...

E-17
Formatting
You can delete all data on P2 cards. 
3. Within 2 seconds, press the [START] button The [COPY STATUS], [P2C], and [HDD] LEDs go out, and P2 card formatting \
begins.
Formatting is complete when the [P2C] LED flashes in orange.
Note:
While the [COPY STATUS], [P2C], and [HDD] LEDs are on in step 2, if you \
do not press the [START]
button  within 2 seconds
(step 3), the P2 card will not be formatted. To format the card, repea\
t the
process from step 2. 
Formatting P2 cards
Data cannot be...

E-18
ENGLISH
Formatting (continued)
Auto power OFF during use
If left unused, the unit will automatically turn OFF after ten minutes i\
f no copying or formatting
operations are in progress. To use the unit, turn it ON again. 
If the unit is left unused while connected to a computer via the USB 2.0\
 cable, auto power OFF
is deactivated, even if no copying or formatting is in progress. To turn\
 the unit OFF, hold the
[POWER] button for at least 2 seconds.
Note that auto power OFF is disabled while...

E-19
Connecting to a computer
Connect the unit to a computer with the USB 2.0 cable to back up data fr\
om P2 cards and the
internal HDD on the computer. System requirements
Your computer must meet these requirements for the P2 driver, the dedica\
ted driver for this
unit, and the dedicated software. 
Operating system: Windows XP Professional SP2 or later Windows 2000 SP4 or later
Macintosh OS X (10.4.2 or 10.4.6), running on a PowerPC-based computer\
Interface: Equipped with a USB 2.0 port
Note: This...