Panasonic Aj Hdr150 Operating Instructions Manual

31
F3 (CH4)
F3 (CH3)
F3 (CH2)
F3 (CH1)
Always be sure the power cord is removed
before installing the optional board.
Optional Board Installation
1. Remove the two coin screws securing the unit’s top
panel. Remove the top panel.
2. Remove the three screws holding down the circuit
board securing fittings, then remove the fittings.
Unplug the two SDTI flat cables from the IF board. 

Be sure to note the connector locations so you can
reconnect them properly when reassembling the
unit later.
3. Connect the...

32
1. Analog I/O board(AJ-YA7000P)
Proceed with the connections in the sequence
described below.
SW1 setting
(for input audio signals with 600-ohm termination) (CH1)
ON: 600-ohm termination OFF: High impedance
SW2 setting
(for input audio signals with 600-ohm termination) (CH2)
ON: 600-ohm termination OFF: High impedance
SW3 setting
For the NTSC system (factory setting)
5: OFF 6: ON 7: OFF 8: ON
For the PAL system (setting must be changed)
5: ON 6: OFF 7: ON 8: OFF
Input audio level selection
1234
+4 dBu...

33
2. Analog out board(AJ-YA7200P)
Perform the connections as illustrated below.
Optional Board Installation Method
ANALOG   DIGITALVIDEO
INOUT
OUT
SDI/SDTI
IN
REMOTE IN AUDIO OUT
AUDIO OUT
VIDEO OUT SW 5 SW 3SW 1 SW 2
SW 9
VIDEO THROUGH
VIDEO IN
Analog out boardRear panel connectors
(designated channel)
Black Red
Orange Analog audio out panel
(packed together with optional board)
SW1 setting
(for input audio signals with 600-ohm termination) (CH1)
ON: 600-ohm termination OFF: High impedance
SW2 setting...

34
3. SDTI I/O board(AJ-YAC7000P)
Perform the connections as illustrated below.
Optional Board Installation Method
S-OUT 3
ANALOG   DIGITALVIDEO
INOUT
OUT
SDI/SDTI
IN
REMOTE IN
S-OUT 1 S-OUT 2
S-INS-IN THROUGH
SDTI I/O boardRear panel connectors
(designated channel)
BlackRed
Orange SDTI cover
(packed together with optional board) 

35
S-INS-IN THROUGHS-OUT
ANALOG   DIGITALVIDEO
INOUT
OUT
SDI/SDTI
IN
REMOTE IN AUDIO OUT VIDEO OUT
AUDIO OUT
VIDEO OUT
Analog out boardRear panel connectors
(designated channel)
4. SDI I/O board(AJ-YA7100P)
Proceed with the connections in the sequence
described below.
1. Connect the cables (for SDI signals a
3) from the
unit to the SDI I/O board.
2. Connect the coaxial cables (for video signals a
1,
for audio signals a
1) packed with the SDI I/O board
to the analog out board.3. Orient the SDI I/O board...

36

OThe optional HDD (AJ-HDD36P) is exclusively for the unit (AJ-HDR150).
Do not use it for any other applications.
If any damages should arise as a result of use for other applications, the Company cannot assume any
responsibility or warranty.  
OTo install the optional HDD, consult your dealer.
Optional HDD
Coin screw
Coin screw 

37
Symptom
$Server’s power LED fails to light
even when the power switch is ON.Suggested remedial action
OHas the power cord been connected?
ODo the installed fuses have the rated amperage?
$No display on the display panel
even though the power switch is
on.
$The buzzer continues to sound
after the operation LED has lighted.OSomething has malfunctioned. 
Check on the display panel.
$No control can be exercised using
RS-422A.OHave the cables been connected properly?
OIs the server mode set to LOCAL?
Check...

38
$REF VIDEO IN
BNCa
2, loop-through with 75 Ωtermination switch
Connector Signals
$SVGA-I/F (for maintenance) 
Pin No. Signal
1 CRV
2 CGV
3 CBV
4___
58 GND
9___
10 GND
11___
12 DCI Comm
13– CHSYNC
14– CVSYNC
15___
$RS-232C (for maintenance) 
Pin No. Signal
1CD
2 RXD
3 TXD
4DTR
5 GND
6 DSR
7 RTS
8 CTS
9CI
$Mouse/Keyboard (for maintenance) 
Pin No. Signal
1 DATA
2___
3 GND
4 +5 V
5 CLOCK
6___
$RS-422A (REMOTE IN)
Pin No. Signal
1 GND
2 RXD –
3 TXD +
4 GND
5 spare
6 GND
7 RXD +
8 TXD –
9 GND
$Fibre...

39
Connector Signals
$Analog I/O board
VIDEO IN:
BNCa
2, loop-through with 75-ohm termination
switch
(This board does not support non-standard
signals.)
VIDEO OUT:
BNCa
1
(The EE output is not locked to the REF input.)
AUDIO IN (ANALOG):
XLRa
2, CH1/CH2
AUDIO OUT (ANALOG):
XLRa
2, CH1/CH2
$Analog out board
VIDEO OUT:
BNCa
1
AUDIO OUT (ANALOG):
XLRa
2, CH1/CH2
$SDTI I/O board
SDTI IN:
BNCa
2, with buffer out
Complies with SMPTE305M standard
SDTI OUT:
BNCa
1
Complies with SMPTE305M standard
(The EE output...

40
[PC component][Control Component]
RS-422A:
4 channel (D-SUB, 9 pin) 
RS-422A protocol:
Odetics/Louth
Playback response time:
At STBY ON:
0.5 sec or less (CUE UP completed) 
At STBY OFF:
2 sec or less (prior to CUE UP) 
RS-232C:
1 channel (for monitor, maintenance) 
Alarms:
Fan alarm, HDD alarm, system alarm
Fibre Channel:
One port each for HOST and RAID
CPU:
Celeron, 433 MHz
OS:
Windows NT 4.0 (English version)
Memory:
128 MB
System HDD:
9 GB a
2 units
Data HDD (Optional):
36 GB a
9 units
Recording...