Panasonic Aj Hdc27v Operating Instructions Manual

31
Audio input preparation
1Open the mic holder.
2Attach  the  microphone,  and  tighten  the  locking
screw.
3Connect the microphone’s connecting cable to the
MIC IN jack on the camera.
When attaching a microphone to
the viewfinder (optional accessory)
for use
The microphone of the AJ-MC700P mic kit (optional
accessory) can be attached to the viewfinder.
AJ-HVF27P
MIC IN jack
Mic holder
Locking
screw
4Set the AUDIO IN switch or switches to “FRONT”
in accordance with the audio channel or channels
whose...

32
Audio input preparation
1Remove the screws used to attach the mic holder.
2Attach  the  mic  holder  to  the  main  unit  using  the
screws provided with the AJ-MH700P mic holder.
Screws provided with mic holder
Locking screw
3Attach  the  microphone  to  the  mic  holder,  and
tighten the locking screw.
4Connect the microphone’s connecting cable to the
MIC IN jack on the camera.
5Set the AUDIO IN switch or switches to “FRONT”
in accordance with the audio channel or channels
whose sound is to be...

33
Audio input preparation
1Connect the microphone’s connecting cable to the
MIC IN jack on the camera.
2Set the AUDIO IN switch or switches to “FRONT”
in accordance with the audio channel or channels
whose sound is to be recorded.
AUDIO IN connectors

When extending the microphone’s connecting cable,
use a cable which supports the phantom power supply
system.

When  the  LINE/MIC/+48V  selector  switch  is  set  to
“+48V,”  the  phantom  power  supply  system  is
supported.
When connecting a microphone...

34
Audio input preparation
1Attach the WX-RJ700 wireless receiver to the WX-
ZJ770 camera attachment.
2Align the grooves in the camera attachment with
the  pins  on  the  battery  case,  etc.  to  attach  the
wireless receiver.
3Connect the AUDIO IN connectors on the camera
with the wireless receiver using the XLR cable.
4Set  the  AUDIO  IN  switch  or  switches  for  the
channel or channels to which the XLR cable has
been connected to “REAR.”
5Set the LINE/MIC/+48V selector switch on the rear
panel to...

35
Mounting the unit on a tripod
1Attach the tripod attachment to the tripod.

Select the attachment holes that best support the
center of gravity of the unit and tripod attachment.
Check  that  the  diameters  of  the  selected  holes
match the diameters of the pan head.
2Attach the camera to the tripod attachment.
Slide  the  camera  toward  the  front  along  the
grooves until it clicks into place. Use  the  tripod  attachment  available  as  an  optional
accessory for mounting the unit onto a...

36
Attaching the shoulder strap
1Attach  the  shoulder  strap  to  the  shoulder  strap
mounting hooks, and adjust the length of the strap.

Check that the shoulder strap is securely fastened.
Shoulder strap
The clip opens
when it is
pressed here.The clip opens when it
is pressed here.
To detach the shoulder strap, open the clips on the
mounting parts and detach.
Adjusting the shoulder pad position
1Loosen the two screws.
2Slide the shoulder pad either backward or forward,
and find the optimum position....

37
AJ-EC3
AJ-65
∫1
Connecting the extension control unit
Dedicated cable
ECU connector
By  connecting  the  AJ-EC3  extension  control  unit
(optional  accessory),  some  of  the  functions  can  be
operated by remote control.
When  the  AJ-EC3  is  connected  and  the  POWER
switches on the unit and AJ-EC3 are set to ON, the
unit is automatically set to the remote control mode.
OBefore connecting or disconnecting the dedicated
cable,  be  absolutely  sure  to  set  the  POWER
switches on the unit and...

38
TALLY / REC
BATT
VTR
SAVE
1
423
Viewfinder lamp displays
1
TALLY/REC (recording) lamp
This  lights  up  (red)  during  recording.    It  flashes
when a problem has occurred.
For  details,  refer  to  the  section  on  the  “Warning
system” (pages 107, 108).
2
BATT (battery) lamp
This starts flashing when the battery voltage has
dropped to the level where the battery will no longer
be  usable  in  several  minutes’  time,  and  it  lights
when the battery is no longer usable.  To prevent
operation...

39
Viewfinder lamp displays
Setting itemDescription of setting
GAIN (0 dB)Lamp display appears when the gain is
set to a value other than “0 dB.”
GAIN (–3 dB)Lamp display appears when the gain is
set to a value other than “–3 dB.”
SHUTTERLamp display appears when the
SHUTTER switch is at ON.
WHITE PRESETLamp display appears when “PRST”
applies to the channel in the white
balance memory.
EXTENDERLamp display appears when the lens
extender is used.
FILTERLamp display appears when the filter is
set to a...

40
Viewfinder screen status displays
In addition to the pictures shot, the unit’s settings and
messages  indicating  its  operating  statuses  are
displayed  on  the  viewfinder  screen.    The  center
marker and safety zone markers also appear.
The items which have been set to ON by the switches
relating to the viewfinder displays or the VF DISPLAY
screen of the setting menu are displayed at the top
and bottom of the screen.
When  settings  have  been  changed  or  adjustments
have been made, messages...