Panasonic Aj Hdc27v Operating Instructions Manual

11
Audio function section (2)
8
AUDIO OUT connector (XLR, 5-pin)
This is connected to the audio component.  
The  sound  of  audio  CH1  and  the  sound  of  audio
CH2 are output separately.
The switching of the recording sound and playback
sound is coupled with the setting of the MONITOR
OUT SDI switch.  (No sound will be output when
the SDI switch is at OFF.)
9
DC OUT (DC power output) socket
This  is  the  DC  12  V  output  socket.    A  current  of
approximately 100 mA can be supplied.
:
ALARM...

12
Viewfinder section
(Viewfinder pictured here is the AJ-HVF27P)
(For  details  concerning  the  viewfinder,  refer  to  the
operating intructions of the viewfinder.)
Parts and their functions
ON
OFF2: 8 7 < >
=
1 ; 9
36 45
3
TALLY switch
This is used to control the front tally lamp 7
.
HIGH:The  brightness  of  the  front  tally  lamp  is
increased.
OFF:The front tally lamp is turned off.
LOW:The  brightness  of  the  front  tally  lamp  is
reduced.
4
PEAKING control
This  is  used  to  adjust  the...

13
2
Synchro scan adjustment switches
These switches become effective when the shutter
switch 7
is  set  to  ON  and  synchro  scanning  is
selected.  They are used to adjust the synchro scan
speed.
When the “–” switch is pressed, the shutter speed is
reduced;  conversely,  when  the  “+”  switch  is
pressed, it is increased.
During  personal  computer  monitor  shooting,  etc.
adjust  these  switches  to  the  positions  where  the
horizontal  bar  noise  inside  the  viewfinder  is
decreased.
3
WHITE...

14
Shooting (recording)/playback
function section (2)
4
OUTPUT  (output  signal  selector)/AUTO  KNEE
switch
This is used to select the video signals which are to
be  output  from  the  camera  unit  to  the  VTR  unit,
viewfinder and video monitor.
The AUTO KNEE function can be used when the
pictures shot by the camera are selected.5
GAIN (gain selector) switch
This is used to select the gain of the video amplifier
in  accordance  with  the  lighting  status  during
shooting.  The gain values...

15
Shooting (recording)/playback
function section (3)
7
SHUTTER switch
This is set to ON when the electronic shutter is to
be  used.    When  the  SEL  side  is  pressed,  the
shutter speed and mode display are changed in the
range which was set ahead of time in the setting
menu.
If this switch setting is changed while the display
mode is set to “2” or “3,” the new setting will appear
at  the  shutter  display  position  on  the  viewfinder
screen.
(Example: “: 1/120”, “: 50%”)
8
ECU  REMOTE  (remote...

16
Shooting (recording)/playback
function section (4)
:
SDI switch
This is used to select the video and audio signals
which  are  to  be  output  from  the  HD  SDI  OUT
connector  and  the  audio  signals  which  are  to  be
output from the AUDIO OUT connectors.
EE/PB:During  playback,  the  playback  video  and
playback  audio  signals  are  output;  in  all
other  modes,  the  EE  video  and  EE  audio
signals are output.
EE:The  EE  video  and  EE  audio  signals  are
output at all times.
OFF:Signal...

17
Shooting (recording)/playback
function section (5)
C
PLAY/PAUSE button
This is pressed to view the playback picture on the
viewfinder screen or using a color video monitor.
The button’s lamp comes on during playback.
When it is pressed during playback, the unit is set
to pause in the playback mode (PLAY PAUSE), and
the button’s lamp flashes.  If the unit is left in the
pause  mode  for  two  minutes,  it  automatically
changes to the stop (STOP) mode.
D
STOP button
This is pressed to stop the tape...

18
Warning/status display section
1
Back tally lamp (unit)
When  the  back  tally  switch 2
is  set  to  ON,  this
lamp  serves  the  same  function  as  the  front  tally
lamp in the viewfinder.
2
Back tally switch 
This is used to control the unit’s back tally lamp 1
.
ON:The unit’s back tally lamp is operational.
OFF:The unit’s back tally lamp is not operational.
3
WARNING lamp
When  a  problem  of  some  form  or  other  occurs
within the VTR unit, this lamp flashes or lights.
4
LIGHT switch
ON:The...

19
1AB 0dBCZ73
¢¢¢¢ VTR USER MENU ¢¢¢¢
¢¢¢¢ CAM USER MENU ¢¢¢¢
Menu operation section
1
Setup card insertion slot
The setup card, available as an optional accessory,
is inserted into this slot.
2
MENU button
When this is pressed, the camera unit’s user menu
screen,  which  was  set  at  the  time  of  shipment,
appears.
When it is pressed again, the VTR unit’s user menu
screen appears. 
When  it  is  pressed  once  more,  the  menu  screen
display is cleared.
The selection of the menu for the user menu...

20
7
“+” button, “–” button
These are used to increment or decrement by 1 the
figure in the digit which was made to flash by the
SHIFT button 8
when the time code or user’s bit is
to be set.
8
SHIFT button
This  causes  the  digit  to  be  set  to  flash  when  the
time code or user’s bit is to be set.
9
TCG (time code selector) switch
This is used to set the running mode of the built-in
time code generator.
F-RUN:Set here to have the time code run all the
time regardless of the VTR’s operation.
This...