Panasonic Aj Hd150 Operating Instructions Manual
Have a look at the manual Panasonic Aj Hd150 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
– 31 – Playback 1Insert the cassette tape, and place the unit in the stop mode. 2Press the PLAY button. Regular playback is now commenced. 3Adjust the audio playback level. Pull out the audio level controls and turn them clockwise or counterclockwise to adjust the levels. Normally, they are kept in the pushed-in state (unity value). 4To end playback, press the STOP button. The VTR now goes into the stop mode. •Check that the SERVO lamp is lighted during playback. If it flashes or if it is off, the images played back will be disturbed.
– 32 – Jog/shuttle Jog mode 1Push the search dial to the “in” position. Be sure that the JOG lamp lights. 2Rotate the search dial. The dial’s clickstops are cleared, and the tape is played back at the speed (–1× to +1× normal speed) corresponding to the speed at which the dial is turned. When the dial rotation is stopped, a still picture appears. The playback picture is noise-free. 3To transfer from the jog mode to another mode, press the appropriate button. Shuttle mode 1Push the search dial to release it from the “in” position. The SHTL lamp lights, and the unit goes into the shuttle mode. •Immediately after the power has been turned on, rotate the search dial and set it to the center position. 2Set the SHTL/SLOW switch to SHTL or SLOW. 3Rotate the search dial. When the SHTL/SLOW switch has been set to SHTL, the playback picture speed is varied from 0 to ±32× normal speed depending on the position of the dial. The playback picture speed can be switched to ±8.4×, ±16× and ±32× normal speed with setting menu No. 101 (SHTL MAX). The dial’s center position is a clickstop where a still picture appears as the playback image. When the SHTL/SLOW switch has been set to SLOW, the playback picture speed is varied from –4.1 to +4.1× normal speed depending on the position of the dial. The maximum speed can be selected using the setup menu No. 308 (VAR FWD MAX) and No. 309 (VAR REV MAX). However, noise appears at speeds other than –1 to +1× normal speed. The dial’s center position is a clickstop where a still picture appears as the playback image. The playback picture is noise-free. 4To transfer from the shuttle mode to another mode, press the STOP button or other button. •When the unit leaves the factory, its operation is set up so that it will be transferred to the shuttle or jog mode when the search dial is rotated. If it is inconvenient for operation to be transferred to the variable-speed mode directly, it can also be transferred through the search button. Set setup menu No. 100 (SEARCH ENA) to KEY.
– 33 – Manual editing 1Select the editing mode. ASSEMBLE:For assemble editing. INSERT:For insert editing. 2Select the editing channel. In the case of insert editing, press the channel button corresponding to the signals to be edited, and check that its lamp is on. 3Press the PLAY button. 4Search for the position where the editing is to be commenced (IN point) while viewing the TV monitor, and press the PLAY and EDIT buttons together at the IN point. 5Press the STOP or PLAY button at the position where editing is to be completed (OUT point) while viewing the TV monitor. The unit goes into the stop mode, and editing is completed.
– 34 – Preroll 1Press the PREROLL button. The VTR now performs the preroll operation. •When the edit IN point has been entered, the tape is rewound from the edit IN point for the duration set by setup menu “000,” and the unit then goes into the stop mode. •When the edit IN point has not been entered, the tape is rewound for the duration set by setup menu “000” from the position where the button was pressed, and the unit then goes into the stop mode. •The time code or CTL signal must be continuously recorded between the edit IN point and preroll point. •When the IN point has not been entered, whether to enter the IN point and perform preroll or to perform preroll without entering the IN point can be selected at setup menu No. 305 (AUTO ENTRY).
– 35 – Automatic editing (Deck to Deck) Editing refers to the job of using a prerecorded tape to produce a complete recording by joining together separate cuts and deleting unnecessary parts. The basic steps taken for editing are as follows. 1Set the CONTROL switch to REMOTE on the player and to LOCAL on the recorder. 2Select the editing mode. 3Enter the edit points of the recorder and player. 4Check and modify the edit points. 5Check (Preview) before proceeding with the editing. 6Proceed with the editing. 7Check (Review) the recording that has resulted from the editing.
– 36 – Automatic editing Switch settings and adjustments When the unit is used as the recorder: When the unit is used as the player: Set the time counter display to TC or CTL. Set the POWER switch to ON.Set the CONTROL switch to LOCAL. Adjust the recording level. ON AUDIO CH SELECTSHIFT ADJTC SETSTART TC/CTLRESET TC INTTCTAPE UB STAND BY EDIT PLAY REW STOPSERVOREC FFREC INHIBIT PLAYEREXT EE MODEREMOTEPUSH REV FWDRECORDERLOCAL CONTROL CH 1 1ASMBL PREVIEW REVIEWAUTO EDITPREROLLTRIMAIN INSET OUT AOUTMULTICUEINSERT VIDEOCH1/5 CH2/8 CH3/7 CH4/8 CUE TCCH 4 OFF POWERCH CONDITION ENTER ESCAPE SHIFT METERFULL/FINE MONITOR SELECT LEVEL HEADPHONES CH 1/5 CH 2/6 CH 3/7 CH 4/8 CUE REC L R PBPULL FOR VARIABLEPULL OPENPULL OPEN CH 5CH 8 2345678 JOGSHTLSLOW EJECT M-cassette / ADAPTERCaution: Do not insert S-cassette without adapter Set the time counter display to TC or CTL. Set the POWER switch to ON.Set the CONTROL switch to REMOTE. Adjust the playback level. ON AUDIO CH SELECTSHIFT ADJTC SETSTART TC/CTLRESET TC INTTCTAPE UB STAND BY EDIT PLAY REW STOPSERVOREC FFREC INHIBIT PLAYEREXT EE MODEREMOTEPUSH REV FWDRECORDERLOCAL CONTROL CH 1 1ASMBL PREVIEW REVIEWAUTO EDITPREROLLTRIMAIN INSET OUT AOUTMULTICUEINSERT VIDEOCH1/5 CH2/8 CH3/7 CH4/8 CUE TCCH 4 OFF POWERCH CONDITION ENTER ESCAPE SHIFT METERFULL/FINE MONITOR SELECT LEVEL HEADPHONES CH 1/5 CH 2/6 CH 3/7 CH 4/8 CUE REC L R PBPULL FOR VARIABLEPULL OPENPULL OPEN CH 5CH 8 2345678 JOGSHTLSLOW EJECT M-cassette / ADAPTERCaution: Do not insert S-cassette without adapter
– 37 – Selecting the editing mode 1Select the editing mode. For assemble editing, press the ASMBL button. For insert editing, press the INSERT button. ASSEMBLE:The assemble editing mode (in which cuts are joined together) is established. INSERT:The insert editing mode (in which cuts are inserted) is established. 2Select the editing channel. With assemble editing, the ASMBL lamp lights. With insert editing, press the button of the channel whose signals are to be edited and light its lamp. 3Select the VTR to be operated (this setting is performed when editing with 2 VTRs). Press the PLAYER or RECORDER button to select the VTR. PLAYER:Press this button to operate the player VTR and enter the edit points. RECORDER:Press this button to operate the recorder VTR (this unit) and enter the edit points. ON AUDIO CH SELECTSHIFT ADJTC SETSTART TC/CTLRESET TC INTTCTAPE UB STAND BY EDIT PLAY REW STOPSERVOREC FFREC INHIBIT PLAYEREXT EE MODEREMOTEPUSH REV FWDRECORDERLOCAL CONTROL CH 1 1ASMBL PREVIEW REVIEWAUTO EDITPREROLLTRIMAIN INSET OUT AOUTMULTICUEINSERT VIDEOCH1/5 CH2/8 CH3/7 CH4/8 CUE TCCH 4 OFF POWERCH CONDITION ENTER ESCAPE SHIFT METERFULL/FINE MONITOR SELECT LEVEL HEADPHONES CH 1/5 CH 2/6 CH 3/7 CH 4/8 CUE REC L R PBPULL FOR VARIABLEPULL OPENPULL OPEN CH 5CH 8 2345678 JOGSHTLSLOW EJECT M-cassette / ADAPTERCaution: Do not insert S-cassette without adapter 1, 2 3 Automatic editing
– 38 – Automatic editing Entering the edit points 1Search for the edit IN point by performing the jog or shuttle operation. Establish the still picture mode at the desired position. Refer to page 32 for details on the jog/shuttle operations. 2Press the IN and SET buttons together. The edit IN point is now entered. The edit IN point value now appears on the display. 3Search for the edit OUT point by performing the jog or shuttle operation. Establish the still picture mode at the desired position. Refer to page 32 for details on the jog/shuttle operations. 4Press the OUT and SET buttons together. The edit OUT point is now entered. The edit OUT point value now appears on the display. Match frame processing function When using two VTRs for editing, a total of four edit points—namely, the player’s IN and OUT points and the recorder’s IN and OUT points—need to be entered. However, since the last edit point is calculated automatically, only three of these edit points must be entered. Negative duration function This function is used by combining setup menu No. 300 (IN/OUT DEL) and No. 301 (NEGA FLASH). ON AUDIO CH SELECTSHIFT ADJTC SETSTART TC/CTLRESET TC INTTCTAPE UB STAND BY EDIT PLAY REW STOPSERVOREC FFREC INHIBIT PLAYEREXT EE MODEREMOTEPUSH REV FWDRECORDERLOCAL CONTROL CH 1 1ASMBL PREVIEW REVIEWAUTO EDITPREROLLTRIMAIN INSET OUT AOUTMULTICUEINSERT VIDEOCH1/5 CH2/8 CH3/7 CH4/8 CUE TCCH 4 OFF POWERCH CONDITION ENTER ESCAPE SHIFT METERFULL/FINE MONITOR SELECT LEVEL HEADPHONES CH 1/5 CH 2/6 CH 3/7 CH 4/8 CUE REC L R PBPULL FOR VARIABLEPULL OPENPULL OPEN CH 5CH 8 2345678 JOGSHTLSLOW EJECT M-cassette / ADAPTERCaution: Do not insert S-cassette without adapter 2, 41, 3
– 39 – Checking the edit points 1Press the IN (or OUT) button to check the edit point. The value of the entered edit point appears on the display. 2Press the PREROLL button while holding down the IN (or OUT) button to check the image at the edit point. The tape is cued at the edit IN (or OUT) point, and the still picture mode at that point is displayed. •The EE mode is established if the TAPE/EE switch has been set to the “EE” position when “STOP” has been selected for the setup menu No. 307 (AFTER CUE-UP). 3Press the IN and OUT buttons together to check the edit duration. The duration time appears on the display. Calculating the duration •When both edit points have been set, the duration between the two edit points. •When only one edit point has been set, the duration between the set data and the current tape address. •When neither edit point has been set, the duration of the previously edited interval. ON AUDIO CH SELECTSHIFT ADJTC SETSTART TC/CTLRESET TC INTTCTAPE UB STAND BY EDIT PLAY REW STOPSERVOREC FFREC INHIBIT PLAYEREXT EE MODEREMOTEPUSH REV FWDRECORDERLOCAL CONTROL CH 1 1ASMBL PREVIEW REVIEWAUTO EDITPREROLLTRIMAIN INSET OUT AOUTMULTICUEINSERT VIDEOCH1/5 CH2/8 CH3/7 CH4/8 CUE TCCH 4 OFF POWERCH CONDITION ENTER ESCAPE SHIFT METERFULL/FINE MONITOR SELECT LEVEL HEADPHONES CH 1/5 CH 2/6 CH 3/7 CH 4/8 CUE REC L R PBPULL FOR VARIABLEPULL OPENPULL OPEN CH 5CH 8 2345678 JOGSHTLSLOW EJECT M-cassette / ADAPTERCaution: Do not insert S-cassette without adapter 21, 3 Automatic editing
– 40 – Automatic editing Modifying the edit points 1Re-entering the edit points Search for the new edit point by performing the jog or shuttle operation, and press the IN (or OUT) and SET buttons together to re-enter the edit point. 2Modifying the edit point in frame units (trim function) Press the TRIM button while holding down the IN (or OUT) button. The edit point is put ahead by 1 frame each time the + button is pressed. The edit point is put back by 1 frame each time the – button is pressed. 3Resetting the edit points 3-1Resetting both the edit IN and OUT points • Press the RESET button. 3-2Resetting either the edit IN or OUT point • Press the RESET button while holding down the IN (or OUT) button. •Edit points can be reset only in the CTL mode. •An edit OUT point can be reset even while editing is in progress. •The IN and OUT points are automatically reset during the eject mode. ON AUDIO CH SELECTSHIFT ADJTC SETSTART TC/CTLRESET TC INTTCTAPE UB STAND BY EDIT PLAY REW STOPSERVOREC FFREC INHIBIT PLAYEREXT EE MODEREMOTEPUSH REV FWDRECORDERLOCAL CONTROL CH 1 1ASMBL PREVIEW REVIEWAUTO EDITPREROLLTRIMAIN INSET OUT AOUTMULTICUEINSERT VIDEOCH1/5 CH2/8 CH3/7 CH4/8 CUE TCCH 4 OFF POWERCH CONDITION ENTER ESCAPE SHIFT METERFULL/FINE MONITOR SELECT LEVEL HEADPHONES CH 1/5 CH 2/6 CH 3/7 CH 4/8 CUE REC L R PBPULL FOR VARIABLEPULL OPENPULL OPEN CH 5CH 8 2345678 JOGSHTLSLOW EJECT M-cassette / ADAPTERCaution: Do not insert S-cassette without adapter 21 3- 1, 3-2