Panasonic Aj D900wa Operating Instructions Manual

							– 111 –
FUNCTION 5/5 Screen
This page performs the adjustment function 5 settings.
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays
the ENG menu.
Item
30 dB
Variable
range
ON
OFF
VF
display
ENGRemarks
This selects the gain applying when
the SUPER GAIN switch is pressed.
SUPER GAIN screen
The gain values to be allocated to the SUPER GAIN switch are set on this screen.
|Note{
When all the gain values have been assigned, the gain is switched in succession to
30 dB or OFF every time the SUPER GAIN switch is pressed.
Variable
range
MENU
ON
MENU
OFF
VF
display
ENGRemarks
This is for selecting whether
characters are to be displayed for the
VIDEO OUT signals.
MENU ON:Characters are displayed.
MENU OFF:Characters are not
displayed.
Item
VIDEO OUT
-F UNC T ION 5/5-
VIDE UTOO:ON¢
MENU
-SUPERGAIN-
¢
30dB
E 
						

							– 112 –
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays
the ENG menu. |Note{
DARK DTL and LEVEL DEPEND
function in a mutually opposite way:
LEVEL DEPEND is automatically
set to 0 when DARK DTL is set to a
value other than 0; and DARK DTL
is automatically set to 0 when LEV-
EL DEPEND is set to a value other
than 0.
Item
MASTER GAIN
H.DTL LEVEL
V.DTL LEVEL
DTL CORING
H.DTL FREQ.
DARK DTL
LEVEL DEPEND.
MASTER
GAMMA
BLACK
STRETCH
MATRIX TABLE
Variable
range
p3 dB
  .
  .
  .
0 dB
  .
  .
  .
30 dB
0
  .
  .
  .
10
  .
  .
  .
31
0
  .
  .
  .
10
  .
  .
  .
31
0
  .
  .
  .
3
  .
  .
  .
15
1
 .
 .
 .
4
5
0
  .
  .
  .
5
0
  .
  .
  .
5
0.35
  .
  .
  .
0.45
  .
  .
  .
0.75
ON
OFF
A
B
OFF
VF
display
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
Remarks
Gains of p3, 0, 3, 6, 9, 12, 15, 18, 21,
24 and 30 dB can be set.
H.DTL (detail) level setting
V.DTL (detail) level setting
DTL coring setting
H.DTL frequency selection
1:2.5 MHz4:4 MHz
2:3 MHz5:4.5 MHz
3:3.5 MHz
Dark detail setting
It boosts the detail of the black areas.
LEVEL DEPEND. setting
It eliminates the detail only in the dark
areas when the Y detail is boosted.
The higher the number selected, the
wider the range across which the detail
is eliminated.
Master gamma setting 0.01 steps
ON/OFF switching for mode which
compensates low-illumination
black-out
Color compensation table selection
Setting Menu Screens
LOW SETTING Screen
This page sets the low level.
-LOWSET T I NG-
¢
MASTERGAIN : 0dB
H.DTL LEVEL : 10
V.DTL
LEVE L : 1 0
DT L CORING:03
H.DTL FREQ.:04
DARKDT L : 0 0
LEVEL DEPEND : 0 0MASTERGAMMA :0.45
MATR I X TABLE : B L ACK S TRE TCH :OFFOFF 
						

							– 113 –
MID SETTING Screen
This page sets the middle level.
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays
the ENG menu.
Item
MASTER GAIN
H.DTL LEVEL
V.DTL LEVEL
DTL CORING
H.DTL FREQ.
DARK DTL
LEVEL DEPEND.
MASTER
GAMMA
BLACK
STRETCH
MATRIX TABLE
Variable
range
p3 dB
  .
  .
  .
9 dB
  .
  .
  .
30 dB
0
  .
  .
  .
10
  .
  .
  .
31
0
  .
  .
  .
7
  .
  .
  .
31
0
  .
  .
  .
6
  .
  .
  .
15
1
  .
  .
  .
4
5
0
  .
  .
  .
5
0
1
  .
  .
  .
5
0.35
  .
  .
  .
0.45
  .
  .
  .
0.75
ON
OFF
A
B
OFF
VF
display
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
Remarks
Gains of p3, 0, 3, 6, 9, 12, 15, 18, 21,
24 and 30 dB can be set.
H.DTL (detail) level setting
V.DTL (detail) level setting
DTL coring setting
H.DTL frequency selection
1:2.5 MHz4:4 MHz
2:3 MHz5:4.5 MHz
3:3.5 MHz
Dark detail setting
It boosts the detail of the black areas.
LEVEL DEPEND. setting
It eliminates the detail only in the dark
areas when the Y detail is boosted.
The higher the number selected, the
wider the range across which the detail
is eliminated.
Master gamma setting 0.01 steps
ON/OFF switching for mode which
compensates low-illumination
black-out
Color compensation table selection
|Note{
DARK DTL and LEVEL DEPEND
function in a mutually opposite way:
LEVEL DEPEND is automatically
set to 0 when DARK DTL is set to a
value other than 0; and DARK DTL
is automatically set to 0 when LEV-
EL DEPEND is set to a value other
than 0.
-MIDSETTING-
¢
MASTERGAIN : 9dB
H.DTL LEVEL : 10
V.DTL
LEVE L : 0 7
DT L CORING:06
H.DTL FREQ.:04
DARKDT L : 0 0
LEVEL DEPEND : 0 1MASTERGAMMA :0.45
MATR I X TABLE : B L ACK S TRE TCH :OFFOFF 
						

							– 114 –
Setting Menu Screens
HIGH SETTING Screen
This page sets the high level.
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays
the ENG menu.
Item
MASTER GAIN
H.DTL LEVEL
V.DTL LEVEL
DTL CORING
H.DTL FREQ.
DARK DTL
LEVEL DEPEND.
MASTER
GAMMA
BLACK
STRETCH
MATRIX TABLE
Variable
range
p3 dB
  .
  .
  .
18 dB
  .
  .
  .
30 dB
0
  .
  .
  .
8
  .
  .
  .
31
0
  .
  .
  .
7
  .
  .
  .
31
0
  .
  .
  .
10
  .
  .
  .
15
1
  .
  .
  .
4
5
0
  .
  .
  .
5
0
  .
  .
  .
2
  .
  .
  .
5
0.35
  .
  .
  .
0.55
  .
  .
  .
0.75
ON
OFF
A
B
OFF
VF
display
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
Remarks
Gains of p3, 0, 3, 6, 9, 12, 15, 18, 21,
24 and 30 dB can be set.
H.DTL (detail) level setting
V.DTL (detail) level setting
DTL coring setting
H.DTL frequency selection
1:2.5 MHz4:4 MHz
2:3 MHz5:4.5 MHz
3:3.5 MHz
Dark detail setting
It boosts the detail of the black areas.
LEVEL DEPEND. setting
LEVEL DEPEND. setting
It eliminates the detail only in the dark
areas when the Y detail is boosted.
The higher the number selected, the
wider the range across which the detail
is eliminated.
ON/OFF switching for mode which
compensates low-illumination
black-out
Color compensation table selection
|Note{
DARK DTL and LEVEL DEPEND
function in a mutually opposite way:
LEVEL DEPEND is automatically
set to 0 when DARK DTL is set to a
value other than 0; and DARK DTL
is automatically set to 0 when LEV-
EL DEPEND is set to a value other
than 0.
--HIGHSETTING
¢
MASTERGA I N : 18dB
H.DTL LEVEL : 08
V.DTL
LEVE L : 0 7
DT L CORING:10
H.DTL FREQ.:04
DARKDT L : 0 0
L EVE L DEPEND : 0 2
MASTERGAMMA :0.55
MATR I X TABLE : B L ACK S TRE TCH :OFFOFF 
						

							– 115 –
LEVEL 1/6 Screen
This page performs the camera setup level 1 settings.
LEVEL 2/6 Screen
This page performs the camera setup level 2 settings.
Item
SKIN TONE DTL
SKIN TONE HUE
SKIN TONE
LEVEL
SKIN TONE
WIDTH
SKIN TONE
CORING
SKIN TONE
ZEBRA
Variable
range
ON
OFF
103
  .
  .
  .
143
1
  .
  .
  .
25
  .
  .
  .
50
1
  .
  .
  .
15
  .
  .
  .
30
1–
5–15
ON
OFF
VF
display
ENG
ENG
ENG
ENG
ENG
ENG
Remarks
Skin tone detail ON/OFF switching
Skin tone hue setting
(This sets the phase of the skin tone
detection range.)
It changes the hue in the phase
direction.
Skin tone level setting
(This sets the intensity of the colors in
the skin tone detection range.)
It changes the level in the amplitude
direction.
Skin tone width settingF
Skin tone coring setting
This changes the amount of SKIN
TONE range detail.
This sets ZEBRA in the SKIN TONE
range to ON or OFF.
This changes the coring in the range
across which ZEBRA can be seen.
GAIN ( ) +00
+16
-L EVE L 1 / 6-
¢
CDTL COMPE . :OFF
CH
H ROMA
H.DT L : 0
:
:1
:1 :0
4 KNEE APERTURE
LINE
MIX:
ON
SL IMDT L :OFF
CORNER DT L :OFF
DT L
GAIN ( ) DT L
DT L
DT LCL I P-+
-L EVE L 2 / 6-
¢
SK I N TONE SK I N TONE
HUE : 103
SK I N T
ONE L EVE L : 2 5
SK I N TONEWI DTH : 1 5
SK I N TONE CORING:05
SK I N TONE Z EBRA :OFF :
OFF DT L
|Note{
Only numbers are displayed while the
variable range of any item except SKIN
TONE ZEBRA ON/OFF is being
changed. FThis sets the range of the colors han-
dled as the skin tone on the basis of the
colors set by SKIN TONE HUE and
LEVEL. The higher the number select-
ed, the wider the skin tone range. FIt detects the chroma edge and places
on Y to boost the H detail. The higher
the number selected, the greater the
compensation.
Item
C DTL COMPE.
CHROMA DTL
KNEE
APERTURE
SLIM DTL
CORNER DTL
DTL GAIN (o)
DTL GAIN (p)
DTL CLIP
H.DTL LINE MIX
Variable
range
ON
OFF
0–2
ON
OFF
ON
OFF
ON
OFF
p31
o0
o31
p31
o16
o31
0
  .
  .
  .
14
  .
  .
  .
31
0H
1H
2H
VF
display
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
Remarks
Chroma DTL ON/OFF switching
Chroma DTL settingF
Knee aperture ON/OFF switching
Detail above the knee point is boosted.
ON/OFF switching for mode which
narrows detail
ON/OFF switching for mode which
increases edge resolution
This changes the H detail level in the
“o” direction.
This changes the H detail level in the
“p” direction.
This changes the clipping of the detail
signals in the positive direction.
This sets the scanning line addition for
generating the horizontal detail signal. 
						

							– 116 –
Setting Menu Screens
LEVEL 3/6 Screen
This page performs the camera setup level 3 settings.
Item
M.PED
SET UP
MANUAL KNEE
KNEE POINT
KNEE SLOPE
WHITE CLIP
WHITE CLIP LVL
AUTO KNEE
POINT
AUTO KNEE
LEVEL
Variable
range
p100
  .
  .
  .
o0
  .
  .
  .
o100
0%
7.5%
7.5%A
ON
OFF
75%
  .
  .
  .
85%
  .
  .
  .
90%
0
  .
  .
  .
25
ON
OFF
90%
  .
  .
  .
110%
75%
  .
  .
  .
85%
  .
  .
  .
90%
100
  .
  .
  .
110
VF
display
ENG
ENG
ENG
ENG
ENG
ENG
ENG
Remarks
M.PED (Master pedestal level) setting
Setup level switching
0%:0% setup for both camera output
and tape.
7.5%:7.5% setup for both camera
output and tape.
7.5%A:7.5% setup for camera output;
0% setup for tape.
FWhen the setting is changed to 0% or
7.5%, chroma and burst levels on the
CAM ENC board are required to
adjust again.
Mode setting when AUTO KNEE
switch is set to OFF
Manual knee point position setting
Manual knee inclination setting
White clip ON/OFF switching
White clip level setting
Auto knee point position setting
Maximum auto knee level setting
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays
the ENG menu.
-L EVE L 3 / 6-
¢
M. PED : +000
SETUP :7.5%
%
% %MANUAA
L KNEE :ON
KNEE POINT
P
OINT:85
KNEE S L
OPE :25WH I TE CLIP:ONWHITE CL I P LVL : 1 1 0
AUTOKNEE
L EVE L:85
AUTOKNEE : 1 1 0 
						

							– 117 –
LEVEL 4/6 Screen
This page performs the camera setup level 4 settings.
Item
R FLARE
G FLARE
B FLARE
R GAMMA
B GAMMA
Variable
range
00
  .
  .
  .
100
00
  .
  .
  .
100
00
  .
  .
  .
100
p15
  .
  .
  .
o00
  .
  .
  .
o15
p15
  .
  .
  .
o00
  .
  .
  .
o15
VF
display
ENG
ENG
ENG
ENG
ENG
Remarks
Rch flare setting
The preset value differs according to
the camera.
Gch flare setting
The preset value differs according to
the camera.
Bch flare setting
The preset value differs according to
the camera.
Rch gamma compensation value for
the master gamma.
Bch gamma compensation value for
the master gamma.
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays
the ENG menu.|Note{
The R FLARE, G FLARE and B FLARE will not be initialized even when the initial-
ization (default setting) operation is performed.
-L EVE L 4 / 6-
¢
R F L ARE :---GF L ARE :---BFL ARE :---RGAMMA:+00BGAMMA:+00 
						

							– 118 –
Setting Menu Screens
LEVEL 5/6 Screen
This page performs the camera setup level 5 settings.
The underlined setting in the Variable range column indicates the preset mode.
|Note{
All settings are “00” for the preset mode of MATRIX TABLE B.
Menu screen display methods
USER menu:Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays
the ENG menu.
Item
MATRIX TABLE
MATRIX R–G
MATRIX R–B
MATRIX G–R
MATRIX G–B
MATRIX B–R
MATRIX B–G
Variable
range
A
B
p31
  .
  .
  .
o0
  .
  .
  .
o31
p31
  .
  .
  .
o0
  .
  .
  .
o31
p31
  .
  .
  .
o0
  .
  .
  .
o31
p31
  .
  .
  .
o0
  .
  .
  .
o31
p31
  .
  .
  .
o0
  .
  .
  .
o31
p31
  .
  .
  .
o0
  .
  .
  .
o31
VF
display
ENG
ENG
ENG
ENG
ENG
ENG
ENG
Remarks
Color adjustment table selection
Color adjustment
Color adjustment
Color adjustment
Color adjustment
Color adjustment
Color adjustment
|Note{
The white balance and black balance remain unchanged even when the MATRIX
items are changed.
-L EVE L 5 / 6-
¢
MATR I X TABLE : AMATR I X R-G:+00
00
00
00
00
00MATR I X R-B:+MATR I XG-R:+MATR I XG-B:+MATR I X B-R:+MATR I X B-G:+ 
						

							– 119 –
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays
the ENG menu.
Item
H PHASE
COARSE
H PHASE FINE
SC PHASE
COARSE
SC PHASE FINE
A.IRIS LEVEL
A.IRIS PEAK/
AVE.
A.IRIS MODE
S.IRIS LEVEL
Variable
rangeRemarks
H phase rough adjustment during
GENLOCK mode.
H phase fine adjustment during
GENLOCK mode.
SC phase rough adjustment during
GENLOCK mode.
SC phase fine adjustment during
GENLOCK mode.
Auto iris target value setting
The brightness (iris) is controlled using
this value. The higher the number
selected, the greater the brightness.
Auto iris peak: average value ratio
setting
The closer the selected value is to 0,
the greater the tendency toward AVE
control; the closer the selected value is
to 100, the greater the tendency
toward PEAK control.
Auto iris mode selection
NORM1:Light metering over entire
screen (except for edges).
NORM2:Light metering over entire
screen (except for top).
CENTR:The light is measured only at
the screen center.
Super iris target value setting
(Backlight compensation mode)
VF
display
ENG
ENG
ENG
ENG
ENG
ENG
ENG
ENG
LEVEL 6/6 Screen
This page performs the camera setup level 6 settings.
-L EVE L 6 / 6-
¢
H PHASE COARSE : 0 7
H PHASE F I NE : 1 2 8
SC PHA
SECOARSE : 0
SC PHASEFINE :1
1 28
A. IRISLEVE L : 0 4 5
A. IRIS PEAK/ AVE : 0 5 0
A.IRISMMODE : NOR
S.IRIS LEVEL : 100
0
  .
  .
  .
7
  .
  .
  .
15
0
  .
  .
  .
128
  .
  .
  .
255
0
  .
  .
  .
3
0
  .
  .
  .
128
  .
  .
  .
255
0
  .
  .
  .
45
  .
  .
  .
100
0
  .
  .
  .
50
  .
  .
  .
100
NORM1
NORM2
CENTR
0
  .
  .
  .
100 
						

							– 120 – Set ting Menu Screens
VF OPERATION Screen
This page performs the viewfinder display settings.
Item
VF OUT
VF DTL
ZEBRA1
DETECT
ZEBRA2
DETECT
ZEBRA2
Variable
rangeRemarksVF
display
Y
NAM
R
G
B
0
 .
 .
 .
2
.
 .
 .
4
50
  .
  .
  .
70
  .
  .
  .
110
50
  .
  .
  .
85
  .
  .
  .
110
ON
OFF
SPOT
VF OUT selection
NAM (N Additive Mix): Signals with the
highest level among R, G and B are
output.
VF DTL selection
The detail of the VF signals is further
boosted. At the “0” setting, the detail is
the same as the main line.
ZEBRA1 DETECT level (IRE value)
setting
ZEBRA2 DETECT level (IRE value)
setting
ZEBRA2 ON/OFF switching and SPOT
selection
FWhen ZEBRA2 is set to SPOT, set
Fthe ZEBRA2 DETECT value higher
Fthan the ZEBRA1 DETECT value. If
Fthe ZEBRA2 DETECT value is less
Fthan the ZEBRA1 DETECT value, the
FZEBRA pattern will not be displayed. ENG
ENG
ENG
ENG
ENG
-VFOPERA T ION-
¢
VFOUT : Y
VF DT L : 2
ZEBRA1 DETECT :
0ZEBRA2 DETECT : 070
85
Z EBRA 2 :
SPOT
The underlined setting in the Variable range column indicates the preset mode.
Menu screen display methods
USER menu:Setting the MENU switch to SET displays the USER menu.
ENG menu:Holding down the SHIFT/ITEM and UP buttons simultaneously and setting the MENU switch to SET displays
the ENG menu.
Item
F2.8 ADJ
F16 ADJ
Variable
rangeRemarksVF
display
——
——Voltage is output only when selected
by the cursor (arrow).
Voltage is output only when selected
by the cursor (arrow). ENG
ENG
|Note{
When using a lens which allows the lens iris open or close end to be adjusted, set
either “F2.8 ADJ” or “F16 ADJ” to ON and repeatedly adjust the lens iris until it is
“F2.8” or “F16”, respectively. (This adjustment need not be performed if the lens
does not have this adjustment function.)
LENS ADJ Screen
This page performs the lens adjustments. The ON/OFF status for each item is indicated by displaying an asterix (E) or period
(.
) in front of the item on the screen.
-L ENS AD J-
¢
.F2.8ADJ.F16 ADJ
E:ON
. 
: OFF