Panasonic Aj D750_200dpi Operating Instructions Manual

Automatic editing (Deck to Deck)
Editing refers to the job of using a prerecorded tape to produce a complete recording by
joining together separate cuts and deleting unnecessary parts.
The basic steps taken for editing are as follows.
Set the CONTROL switch to REMOTE on the player and to LOCAL on the recorder.
Select the editing mode.
Enter the edit points of the recorder and player.
Check and modify the edit points.
Check (Preview) before proceeding with the editing.
Proceed with the editing.
Check...

Automatic editing 
Switch settings and adjustments
When the unit is used as the recorder:
Select the video and audio input
Set the POWER switchsignals using the INPUT SELECT
Set the CONTROLto ON.switches.
switch to LOCAL.
Adjust the recording level.
Set the time counter display to TC or CTL.
When the unit is used as the player:
Set the POWER switch to ON.
Set the CONTROL
switch to REMOTE.
Adjust the playback level.Set the time counter display to TC or CTL.
-32- 

Select the editing mode
Select the editing mode.
For assemble editing, press the ASSEMBLE button.
For insert editing, press the INSERT button.
ASSEMBLE: The assemble editing mode (in which cuts are joined together) is
INSERT:
established.
The insert editing mode (in which cuts are inserted) is established.
Select the editing channel.
With assemble editing, the ASSEMBLE lamp light.
With insert editing, press the button of the channel whose signals are to be edited and
light its lamp.
Select the VTR to be...

Automatic editing
Entering the edit points
Search for the edit IN point by performing the jog or shuttle operation.
Establish the still picture mode at the desired position.
Refer to page 28 for details on the jog/shuttle operations.
Press the IN and SET buttons together.
The edit IN point is now entered.
The edit IN point value now appears on the display.
Search for the edit OUT point by performing the jog or shuttle operation.
Establish the still picture mode at the desired position.
Refer to page 28...

Checking the edit points
Press the IN (or OUT) button to check the edit point.
The value of the entered edit point appears on the display.
Press the IN (or OUT) button while holding down the PREROLL button to check the
image at the edit point.
The tape is accessed at the edit IN (or OUT) point, and the still picture mode at that
point is displayed.
Press the IN and OUT buttons together to check the edit duration.
The duration time appears on the display.
Calculating the duration
When both edit points...

Automatic editing
Modifying the edit points
Re-entering the edit points
Search for the new edit point by performing the jog or shuttle operation, and press the
IN (or OUT) and SET buttons together to re-enter the edit point.
Modifying the edit point in frame units (trim function)
Press the TRIM button while holding down the IN (or OUT) button.
The edit point is put ahead by 1 frame each time the + button is pressed.
The edit point is put back by 1 frame each time the – button is pressed.
Resetting the...

Preview
After the edit points have been entered, press the PREVIEW button.
Normal preview is now performed.

If the edit IN point has not been entered, the position where the PREVIEW button
was pressed will be entered at the edit IN point.
To stop the preview at any time, press the STOP button.
If the PREVIEW button is pressed again while preview is in progress after the IN
point, preview will start again from the beginning.
When the edit OUT point is reached, the unit automatically goes into the stop...

Automatic editing
Executing automatic editing
Press the AUTO EDIT button.
Automatic editing is now performed.
To stop the editing at any time, press the STOP button.
When the edit OUT point is reached, the unit goes into the stop mode after
postrolling.
Postroll
With assemble editing, editing continues for approx. 2 seconds even after the edit OUT point
has been passed, the tape is rewound to the OUT point, and the unit goes into the stop
mode.
With insert editing, the unit goes into the play mode after...

Review
Upon completion of the editing, press the REVIEW button.
The review is started in the recorder.
To stop the review at any time, press the STOP button.
When the edit OUT point is reached, the unit goes into the stop mode after
postrolling.
1
-39- 

Split editing 
Split editing refers to editing where the editing channels are switched while insert editing is
in progress.
Perform insert editing.
Switch the editing channel.
When, for instance, sound from AUDIO CH2 is to be additionally inserted during video
channel insert editing:
2-1Press the AUDIO CH2 button during video channel editing.
The lamp in the button lights and the AUDIO CH2 sound is insert edited.
2-2Press the AUDIO CH2 button again and turn off the lamp in the button.
This completes the...