Panasonic Aj D400 Operating Instructions Manual

							– 121 – Inspections Before Shooting
Inspecting the Viewfinder
1Adjust the position of the viewfinder.
2Check that the color bar appears on the viewfinder screen, and then adjust the BRIGHT,
CONTRAST and PEAKING controls so that the color bar appears clearly on the viewfinder.
3Check the following items.
(1) Set the MENU SET/OFF switch to SET and check that the setting menu appears on
the viewfinder screen.
(2) Press the PAGE button and check that the setting menu page changes.
(3) Press the SHIFT/ITEM switch and check that the cursor moves within the page.
(4) Press the UP or DOWN button to check that the setting or ON/OFF display of the item
selected with the cursor changes.
4Set the OUTPUT/AUTO KNEE switch to CAM and switch the FILTER knob to 1, 2, 3 and 4.
Check that the number of the FILTER display on the viewfinder screen changes in accor-
dance with the knob position.
5Perform the following operations to check that the (!) lamp lights when the items set to ON
at the (!) LED page are operated.
(1) Set the gain to any value other than 0 dB with the GAIN switch.
(2) Set the SHUTTER switch to ON.
(3) Set the WHITE BAL switch to PRST.
(4) Insert the lens extender.
(5) Set the FILTER knob to any position other than “1”.
6Press the SHUTTER switch repeatedly from the ON position to the SEL side and check that
the shutter setting on the viewfinder screen changes.
7Aim the lens at an appropriate subject and turn the focus ring to bring the subject into focus.
Check the image appearing in the viewfinder.
8Set both the AUDIO IN CH1 and CH2 switches to FRONT [MIC] and set LEVEL METER on
the VF DISPLAY page of the setting menu to ON. Check that the audio level appears on the
viewfinder screen when sound is input from the microphone connected to the MIC IN jack
on the front panel. Then, check that the audio level disappears from the viewfinder screen
when LEVEL METER on the VF DISPLAY page of the setting menu is set to OFF.
9Check that the zebra pattern appears on the viewfinder screen when the ZEBRA switch is
set to ON, and disappears when the ZEBRA switch is set to OFF.
|Note{
The items and functions in steps 3 to 6 may not be displayed or may not operate depending on
the setting conditions. Set the unit to engineer mode, set DISPLAY MODE on the VF DISPLAY
page of the setting menu to “3”, and then set the required items at the SHUTTER SPEED, (!)
LED and MENU SELECT 1/3 to 3/3 pages. 
						

							– 122 – Inspections Before Shooting
Inspecting the Iris and Zoom Functions
1Set the zoom to electric zoom mode and check the electric zoom operation. Check that
the image changes to telephoto and wide angle.
2Set the zoom to manual zoom mode and check the manual zoom operation. Turn the
manual zoom lever and check that the image changes to telephoto and wide angle.
3Set the iris to automatic adjustment mode and aim the lens at subjects with differing
brightness to check that the automatic iris adjustment functions.
4Set the iris to manual adjustment mode and turn the iris ring to check the manual iris ad-
justment.
5Hold down the instant iris automatic adjustment button and aim the lens at subjects with
differing brightness to check the instant iris automatic adjustment performance.
6Return the iris to automatic adjustment mode and change the GAIN switch setting toL, M
and H to check the following items.
ÁThe iris is adjusted with respect to subjects with the same brightness in accordance with
the switch setting.
ÁThe gain value display on the viewfinder screen changes in accordance with the switch
setting.
7When a lens with an extender is mounted, set the extender to the used position to check
that the extender functions properly.
Perform “(1) Tape Running Inspections” to “(4) Earphone and Speaker Inspections” below consecutively.
Inspecting the VTR Section
(1) Tape Running Inspections
1Set the VTR SAVE/STBY switch to SAVE and check that the VTR SAVE lamp inside the
viewfinder lights.
2Set the VTR SAVE/STBY switch to STBY and check that the VTR SAVE lamp goes off.
3Set the F-RUN/R-RUN switch to R-RUN.
4Set the DISPLAY switch to CTL.
5Press the unit’s VTR START button and check the following items.
ÁThe tape reels turn.
ÁThe counter display number changes.
ÁThe REC lamp inside the viewfinder lights.
ÁThe RF and SERVO lamps in the display window do not light.
6Press the unit’s VTR START button again. Check that the tape stops and the REC lamp
inside the viewfinder goes off.
7Check the same operations as in steps 5 and 6 using the VTR button of the lens.
8Press the RESET button and check that the counter display number changes to
“00:00:00:00”.
9Set the LIGHT switch to ON and check that the display window is illuminated.
10Press the REW button and then press the PLAY button after the tape has rewound for a
while. Check that the recording, playback and rewind operations are performed properly.
11Press the FF button and check that fast forward operation is performed properly. 
						

							– 123 – Inspections Before Shooting
(2) Inspection of Audio Level Automatic Adjustment Functions
1Set the AUDIO SELECT CH1/CH2 switch to AUTO.
2Set the AUDIO IN CH1/CH2 switch to FRONT [MIC].
3Aim a microphone connected to the MIC IN jack at an appropriate sound source and check
that the level display for both CH1 and CH2 changes in accordance with the sound level.
(3) Inspection of Audio Level Manual Adjustment Functions
1Set the AUDIO IN CH1/CH2 switch to FRONT [MIC].
2Set the AUDIO SELECT CH1/CH2 switch to MAN.
3Turn the AUDIO LEVEL CH1/CH2 controls and check that the level display increases when
the controls are turned to the right.
(4) Earphone and Speaker Inspections
1Set the VTR SAVE/STBY switch to STBY.
2Turn the MONITOR control and check that the speaker volume changes.
3Connect an earphone to the PHONES jack. Check that the sound to the speaker is cut off
and that the microphone sound can be heard from the earphone.
4Turn the MONITOR control and check that the earphone volume changes.
(5) Inspections when Using an External Microphone
1Connect an external microphone to the AUDIO IN CH1 and CH2 connectors.
2Set the AUDIO IN CH1/CH2 switch to REAR [MIC].
3Aim the microphone at a sound source and check that the audio level meter in the display
window and the audio level display inside the viewfinder change in accordance with the
sound level. Each channel can also be checked separately by connecting a single micro-
phone to each channel.
(6) Time Code and User Bit-Related Inspections
1Set the user bit as necessary.
ÁSee “Setting the User Bit” (page 76) for a description of setting methods.
2Set the time code.
ÁSee “Setting the Time Code” (page 75) for a description of setting methods.
3Set the F-RUN/R-RUN switch to R-RUN.
4Press the VTR START button.
Check that the tape runs and the counter display number changes.
5Press the VTR START button again.
Check that the tape stops and the counter display number stops changing.
6Set the F-RUN/R-RUN switch to F-RUN.
Check that the counter display number changes regardless of the tape running status.
7Set the DISPLAY switch to UB.
Check that the set user bit is displayed. 
						

							– 124 – Specifications
General
Operating temperature:32uF to 104uF
Storage temperature:p4uF to 140uF
Operating humidity:Less than 85% (relative humidity)
Continuous operating time:Approx. 90 min. (using 1 Anton Bauer Trimpac 14 battery)
Weight:Approx. 12.87 lbs (5.85 kg) (incld. main unit, viewfinder, lens,
battery pack, tape and microphone)
Dimensions:4
1/2½ (W)q101/16½ (includ. handle) (H)q127/8½ (D)
119.2q255.5q326.3 mm
Camera Section
Pick-up devices:1/2-inch on-chip FIT type of CCD
System:RGB 3-CCD system
Picture elements:410,000 pixel
Spectral system:F1.4 prism system
Built-in filters:1; 3200K
2; 5600Ko1/4 ND
3; 5600K
4; 5600Ko1/16 ND
Quantization:10-bit A/D (R, G and B channels), 14.3 MHz
Digital signal processing:16-bit long operation, 14.3 MHz/28.6 MHz
Horizontal drive frequency:14.3 MHz
Programmable gains:3 positions can be set from among p3, 0, 3, 6, 9, 12, 15, 18,
21, 24 and 30 dB.
Super gain:30 dB
Shutter speeds:1/100, 1/120, 1/250, 1/500, 1/1000 and 1/2000 sec.
Synchro scan mode; 1/30.4 – 1/57.4 sec., 1/61.7 – 1/250 sec.
Lens mount:1/2½ Bayonet type
Sensitivity:F8 (2000 lux, 89.9% reflection)
Minimum subject brightness:2 lux (F1.4, o30 dB)
Image S/N ratio:62 dB (typical)
Horizontal resolution:750 lines (center)
Vertical resolution:400 lines/more than 450 lines (Super V mode)
Sampling frequency:14.3 MHz/28.6 MHz
Registration:Below 0.03% (entire range) (excld. lens)
Geometric distortion:Below measurable limit (excld. lens)
Viewfinder
CRT:1.5½ monochrome
Resolution:600 lines (center)
Controls/Switches:Controls; BRIGHT, CONTRAST, PEAKING
Switches; TALLY, ZEBRA Power supply voltage:DC 12 V
Power consumption:23 W 
						

							– 125 – Specifications
VTR Section
VTR Video System (during playback on a standard playback unit)
Bands:Brightness; 30 Hz to 5.75 MHzo1.0 dB/p3.0 dB
S/N ratio:55 dB
K factor (2T pulse):Within 2%
Y/C delay:Within 30 ns
VTR Audio System (during playback on a standard playback unit)
Sampling frequency:48 kHz (synchronized to video)
Quantization:16-bits/sample
Frequency response:20 Hz to 20 kHzt1.0 dB (at reference level)
Dynamic range:80 dB or more (at 1 kHz, AWTD)
Distortion:Within 0.1% (at 1 kHz, operating level)
Wow/flutter:Below measurable limit
Head room:20 dB
Emphasis:T1r50 ¯s, T2r15 ¯s (can be turned ON/OFF)
VTR Tape Running System
Tape speed:33.820 mm/s
Recording/playback time:Approx. 66 min. (using the AJ-P66MP)
FF/REW time:Approx. 3 min. (using the AJ-P66MP)
Connectors
Input
AUDIO IN CH1/CH2
(XLRX2, 3-pin, female):MIC/LINE switchable, balanced, more than 10 kohm
MIC; Menu setting to p60/p50/p40 dBu
LINE; Menu setting to p6/0/o4 dBu
MIC IN (XLR, 3-pin, female):Phantom o48 V, balanced, 3 kohm
Menu setting to p60/p50/p40 dBu
GENLOCK IN (BNC):1.0 Vp-p, 75 ohm
Output
CAMERA OUT (BNC):1.0 Vp-p, 75 ohm
VIDEO OUT (BNC):1.0 Vp-p, 75 ohm
AUDIO OUT (CH1/CH2/MIX)
(XLR, 3-pin, male):o4 dBu, balanced, low-impedance
(Menu setting to CH1/CH2/MIX)
PHONES (mini-jack·1):
Other
DC IN (XLR, 4-pin, male):DC 11 to 17 V
DC OUT (4-pin):DC 11 to 17 V, maximum rated current; 0.1 A
LENS (12-pin):
REMOTE (ECU, 6-pin):
Accessories
Microphone kit
Tripod attachment
Sony battery connector (screw included)
Weight and dimensions shown are approximate.
Specifications are subject to change without notice. 
						

							– 126 – Specifications
Related Components
Power supply related
AU-BP220, AU-BP402 battery packs
AG-B425 battery charger (for charging the AU-BP220 and AU-BP402 battery packs)
AU-M402H battery case
AJ-B75 AC adaptor
Viewfinder
5-inch viewfinder
External VTR-related
Portable video cassette recorder
AJ-YA710PF time code input/output/video input adaptor
AJ-YA900P 26-pin/12-pin output adaptor (for connecting an external VTR to the 26-pin inter-
face)
AJ-YA700PF 26-pin output adaptor (for connecting an external VTR to the 26-pin interface)
AQ-EC1 extension control unit
Connection cables
Áfor connecting an external VTR to the 26-pin interface
Áfor connecting an external VTR to the 14-pin/26-pin interface
ÁSHAN-C12TCA multi connector cable
FVideo input connector can only be used for return video input.
Audio components
AJ-MH700P microphone holder
WX-RA700 wireless receiver
WX-R980 camera attachment
Maintenance products
AJ-CL12MP cleaning tape
AJ-SC900 soft carrying case
SHAN-B700 carrying case
SHAN-RC700 rain cover 
						

							– 127 – 
						

							PANASONIC BROADCAST & DIGITAL SYSTEMS COMPANY
DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
Executive Office:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Mid-Atlantic/New England:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Dallas Region:
6226 Abington Way, Houston, TX 77008 (713) 802-2726
No. CA/Northwest Region:
5870 Stoneridge, #3, Pleasanton, CA 94588 (925) 416-5108
Government Marketing Department:
52 West Gude Drive, Rockville, MD 20850 (301) 738-3840
PARTS INFORMATION & ORDERING:
9:00 a.m. – 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880
TECHNICAL SUPPORT:
Emergency 24 Hour Parts & Service (800) 222-0741
TRAINING INFORMATION:
Digital System Products - (201) 392-6852
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010
Panasonic de Mexico S.A. de C.V.
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127