Panasonic A15 And A35 Bullet Camera Quick Start Guide

							Network Bullet Camera·Quick Operation Guide  10● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection.  ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly.  Steps: 1. Attach the drill template on the wall.  Figure 2-1 Attach the template 2. Secure the camera to the ceiling with the supplied expansion screws. Screw HoleTemplate 
						

							Network Bullet Camera·Quick Operation Guide  11 Figure 2-2 Secure the Camera to the Ceiling 3. Adjust the Lens.  1). Loosen the adjustable nut on the bracket. 2). Adjust the panning angle [0~360°] of the camera. 3). Adjust the tilting angle [0~90°] of the camera. 4). Rotate 0~360° to adjust azimuth angle of the image. 5). Tighten the adjustable nut to complete the installation.  AdjustableNutT DirectionR DirectionP Direction 
						

							Network Bullet Camera·Quick Operation Guide  12Figure 2-3 3-axis Adjustment 
						

							Network Bullet Camera·Quick Operation Guide  133 Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or PCNVR software to search and change the IP of network camera.  The following figure shows the cable connection of network camera and PC:  Figure 3-1 Wiring over LAN  Set the IP address of the camera for accessing via LAN. Steps: To set the IP address, please use the Advidia Camera Finder Utility as described below:  To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the Advidia Camera Finder Utility.  
						

							Network Bullet Camera·Quick Operation Guide  14Refer to the following introductions to set IP address with the Advidia Camera Finder Utility software (for more detailed instructions please download the Camera Finder manual from the Advidia Website www.advidia.com/support):  After launching the Advidia Camera Finder software, it automatically searches the online devices from the subnet where your computer is located.  This search may take 30 seconds or more depending on network size. After searching it will show total number and information of the Advidia cameras found on the network. Device information including the device type, IP address, port number, gateway, etc. will be displayed.  Figure 3-2 Advidia Camera Finder Note: To perform a manual search for additional cameras:  
						

							Network Bullet Camera·Quick Operation Guide  15Click the refresh icon  to refresh the online device list manually. The newly discovered devices will be added to the list. Note: You can click on each column heading to order the information.  Modify device information Steps: 1). Select the device(s) to be modified in the device list as shown in Figure 3-3.  2). Click on “File” and select “Login Manager ” as shown in Figure 3-4 to enter the username and password information of selected device(s). 3). Enter the username and password information of the admin account of each device you wish to modify in the “Username” and “Password” fields and click the Save icon  to save the changes. 4). Close the Login Manager and select “Launch Edit Table” under the “Edit” menu dropdown or with Ctrl+E as seen in figure 3-5.  Figure 3-3 Select a Device  
						

							Network Bullet Camera·Quick Operation Guide  16     Figure 3-4 Login Manager   Figure 3-5 Launch Edit Table   
						

							Network Bullet Camera·Quick Operation Guide  17 Figure 3-6 Edit Table 5) Enter the desired IP address (or range if changing the IP address of more than one device) of the network camera in the address field of the edit table and click Apply Network Changes. You can also select “Dynamic IP” if you would prefer to have an IP address assigned by your network router.   The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”. For security purposes the default Username and password should be changed to something unique.  For accessing the network camera from different subnets, please set the gateway for the network camera after you log in.  
						

							Network Bullet Camera·Quick Operation Guide  184 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above version Steps: 1) Open the web browser. 2) In the browser address bar, input the IP address of the network camera, e.g., 192.0.0.64 and press the Enter key to enter the login interface. 3) Input the user name and password. 4) Click Login.  
						

							Network Bullet Camera·Quick Operation Guide  19 Figure 4-1 Login Interface 5) Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.