Panasonic 8410 Operating Instructions Manual

							131
Communication cannot
be established between
the printer and your
computer.Install a media tray with
media in it.
Media Tray 
Empty All Media Tray
missing or empty
Fuser Unit and Oil Roll
Worn outCall for service. Lower Tray
Empty
Corrective ActionError Message
Care and Maintenance
Possible Cause
Paper Tray
Empty
Transparency Tray
Empty
Output Tray
Full
SIMM Check Error
SCSI error
Ethernet Card
Check Error
Imaging Unit
Worn out
Imaging Unit wearing out
Transfer wearing out
Fuser Unit wearing out
Oil Roll
Worn out
Oil Roll wearing out
Black Toner
Empty Multi-Purpose Tray
EmptyMulti-purpose tray is
empty.Install media in the
multi-purpose tray.
Install a media tray with
paper in it.
Install a media tray with
transparencies in it.
Remove the printed
media from the output
tray.
Connect the SCSI cable
correctly.
Install the Ethernet Card
correctly. No media tray is
installed or media tray
is empty.
No media tray is
installed or media tray
is empty.
Output tray is full.
Controller Optional
SIMM check error.
Printer Ethernet Card
I/F Error.
Imaging unit is worn
out.
Imaging unit is wearing
out.
Second transfer roller is
wearing out.
Fuser is worn out.
Fuser is wearing out.
Oil supply roll is worn
out.
Oil supply roll is
wearing out.
Black toner cartridge is
empty.
Install media in the
upper media tray.
Install media in the
middle media tray.
Install media in the
lower media tray. Media tray is empty.
Middle tray is empty in
the 2nd cassette feeder
option.
Lower tray is empty in
the 2nd cassette feeder
option. Upper Tray
Empty
Middle Tray
Empty
Replace the imaging
unit now.
Replace the imaging
unit soon.
Replace the transfer
roller soon.
Replace the fuser unit
now.
Replace the fuser unit
soon.
Replace the oil supply
roll now.
Replace the oil supply
roll soon.
Replace the black toner
cartridge now.
Media tray is missing or
empty All media trays are
missing or empty.
Install the media tray
with media in it. 
						

							132
The printer is too hot or
room temperature is
too high to print Labels. Cyan Toner
Empty
Error Message
Too hot to print Label
Remove Label, Cancel jobCorrective Action
Yellow toner cartridge
is almost empty. Yellow toner cartridge
is empty.
Care and Maintenance
Possible Cause
Low Black Toner
Low Cyan Toner
Low Magenta Toner
Low Yellow TonerBlack toner cartridge is
almost empty.
Cyan toner cartridge is
almost empty.
Magenta toner
cartridge is almost
empty.
Yellow Toner 
EmptyReplace the yellow
toner cartridge now.
Replace the black toner
cartridge soon.
Replace the cyan toner
cartridge soon.
Replace the magenta
toner cartridge soon.
Replace the yellow
toner cartridge soon.
Wait until the printer
cools down, or use in a
cooler place [below
32.5°C (90.5°F)].
Replace the magenta
toner cartridge now. Magenta Toner
EmptyCyan toner cartridge is
empty.
Magenta toner
cartridge is empty.Replace the cyan toner
cartridge now. 
						

							133
Close all applications
and turn off the
computer, then turn it
on again. An illegal error has
occurred. KX-P8410 or Printer Driver
is illegal condition. Abort
printing.
Error messagePossible causeRecovery
Care and Maintenance
Reinstall the KX-P8410
software. 1/16 compression table
is not found.
Check the cable
connection of the
printer or turn on the
printer. The printer connected
with the parallel cable
is not recognized. Block 16 table open error:
Table file not open!
BReprint later when
the printer is free
from other jobs. The printer is printing. KX-P8410 is not detected.
Selected port is LPT.
Please check LPT cable,
Power ON or Printer
condition.
The printer is being
used by another
device. KX-P8410 is already used
by other devices.BReprint later when
the printer is free
from other jobs.
BTurn off the printer
and the computer,
then turn them on
again.
KX-P8410 is not detected.
Selected port is SCSI.
Please check SCSI cable,
Power ON or Printer
conditionKX-P8410 is not
recognized as a SCSI
device.Check the cable
connection of the
system or turn on the
printer.
BConfirm the SCSI
board is correctly
installed in the
computer or cable is
correctly connected.
BTurn off the
computer, then turn it
on again.
LPT Port or KX-P8410 is
busy.
Printer Driver For Windows 3.1
ASPI does not support this
mode!!Correctly install the
SCSI board and its
driver. (Refer to the
manual of the SCSI
board.)
For any other trouble
related to SCSI, refer to
the SCSIsection of
Care and Maintenance
( +P. 127). ASPI is not initialized!!SCSI board and its
driver are not installed
correctly.
The transfer data area
for printing has
allocated more than
16MB. Memory is allocated Above
16MB. If your SCSI
controller is connected in
an ISA slot, Printing may
not print correctly!! 
						

							134
Turn off the printer and
the computer, then turn
them on again. Print the
document again. SCSI Error!! Time Out
occurred.
Unable to Allocate Memory The computer’s
internal memory for
printing is insufficient. The printer is not
responding.
Error messagePossible causeRecovery
Care and Maintenance
*.DLL not found *.DLL function Error The necessary file for
printing is not found.Reinstall the KX-P8410
software.
nSome application settings may take priority over the printer driver settings.BClose all applications
except for the one
which controls the
printer, then print
again.
BTurn off the
computer, then turn it
on again.
Printing aborted for
occurred SCSI error.An illegal error has
occurred.BConfirm the SCSI
board is correctly
installed in the
computer or cable is
correctly connected.
BTurn off the
computer, then turn it
on again.
Correctly install the
SCSI board and its
driver. (Refer to the
manual of the SCSI
board.)
For any other trouble
related to SCSI, refer to
the SCSIsection of
Care and Maintenance
( +P. 127). SCSI board and its
driver are not installed
correctly. No ASPI managers were
found!!
One or more ASPI for DOS
managers are loaded which
do not support ASPI for
WIN16!! 
						

							135
Correctly install the
SCSI board and its
driver. (Refer to the
manual of the SCSI
board.)
wnaspi32.dllwill be
installed or replaced
with a new version.
For any other trouble
related to SCSI, refer to
the SCSIsection of
Care and Maintenance
( +P. 127).
The ASPI manager
installed on this PC does
not support Windows.
Install ASPI for Windows.
[e.g. install wnaspi32.dll to
your windows (system
directory)]. The ASPI for Windows
installed on this PC does
not support expected
mode. Install newer version
of ASPI for Windows.
Error messagePossible causeRecovery
ASPI Manager is not found.
Install ASPI for Windows.
(e.g. install wnaspi32.dll to
your windows (system
directory.)
Care and Maintenance
Can not find Panasonic KX-
P8410. Make sure that
Panasonic KX-P8410 is
connected to your PC by
SCSI, and then retry again.Correctly install SCSI
board and its driver.
(Refer to the manual of
the SCSI board.)
wnaspi32.dllwill be
installed or replaced
with a new version. SCSI board and its
driver are not installed
correctly.
BCable connection is
improper or printer is
not ready.
BThe terminator
setting is improper.
The ASPI for Windows
installed on this PC does
not have expected function.
Install newer version of
ASPI for Windows.SCSI board and its
driver are not installed
correctly.Perform the following
procedure.
1. Confirm that the
terminator is correctly
set.
2. Confirm that the
printer is ready.
3. Confirm that the
printer is correctly
connected with a
SCSI cable.
4. Turn off the
computer, then turn it
on again.
Can not initialize ASPI for
Windows. Install newer
version of ASPI for
Windows
Printer Driver For Windows 95 
						

							136
BClose all applications
except for the one which
controls the printer, then
print it again.
BTurn off the computer,
then turn it on again.
Print the document
again. Follow the procedure
below to make the setting
active.
1. Click Start, select
Settings, then click
Printers.
2. Click the Panasonic 
KX-P8410 printericon.
3. Click the File menu,
then click Properties.
4. Click Details tab and
Spool settings....
5. Click Enable bi-
directional support for
this printer, then click
OK.
Error messagePossible causeRecovery
Unable to Allocate
Memory!!
Care and Maintenance
BCable connection is
improper or the
printer is not ready.
BThe terminator
setting is improper. There was an error
writing to LPT1: for the
printer (Panasonic 
KX-P8410):
There was a problem
sending your document
to the printer. Make sure
the printer cable is
connected and the
printer is online. To
continue printing, click
retry. Windows will
automatically retry after
5 secondsConnect the printer
(parallel cable) correctly or
make the printer ready. Cable connection is
improper or the printer
is not ready.
The memory for
printing is insufficient. The Status Display
does not appear when
printing a document.The Status Display
function is not active
nSome application settings may take priority over the printer driver settings.There was an error
writing to KXP8410GDI:
for the printer
(Panasonic KX-P8410):
The printer is not ready.
Make sure it is turned
on and online. To
continue printing, click
retry. Windows will
automatically retry after
5 secondsPerform the following
procedure.
1. Confirm that the
terminator is correctly
set.
2. Confirm that the printer
is ready.
3. Confirm that the printer
is correctly connected
with a SCSI cable.
4. Turn off the computer,
then turn it on again. 
						

							Error writing to
KXP8410GDI: for : The printer command
is invalid. Do you wish to
retry or cancel the job?
137
Care and Maintenance
Error messagePossible causeRecovery
Can not initialize ASPI for
Windows. Install newer
version of ASPI for
Windows.SCSI Board and its
driver are not installed
correctly.Correctly install SCSI board
and its driver. (Refer to the
instructions manual of the
SCSI board.)
Wnaspi32.dll will be
installed or replaced with a
new version.
For any other trouble related
to SCSI, refer to the SCSI
section of Care and
Maintenance ( 
+P. 127).
ASPI Manager is not
found. Install ASPI for
Windows. (e.g. install
wnaspi32.dll to your
system32 directory).SCSI Board and its
driver are not installed
correctly.Correctly install SCSI board
and its driver. (Refer to the
instructions manual of the
SCSI board.)
Wnaspi32.dllwill be
installed or replaced with a
new version.
The ASPI for Windows
installed on this PC does
not have expected
function. Install newer
version of ASPI for
Windows.
The ASPI for Windows
installed on this PC does
not support expected
mode. Install newer
version of ASPI for
Windows.
The ASPI for Windows
installed on this PC does
not support Windows.
Install ASPI for Windows.
[e.g.install wnaspi32.dll to
your system32 directory]
Printer Driver For Windows NT 4.0
Separator page has
been set. When SCSI
port is used, Separator
page cannot be used.Cancel the Separator page
setting.
Error writing to LPT1: for
“Application name”: The
device is not ready. Do
you wish to retry or
cancel the job?Connect the printer (parallel
cable) correctly or make the
printer ready. Cable connection is
improper or printer is not
ready. 
						

							138
Care and Maintenance
System Process-Out of
Virtual Memory 
Your system is running
low on virtual memory.
Please close some
applications. You can
then start the System
option in the Control
Panel and choose the
Virtual Memory button to
create an additional
paging file or to increase
the size of your current
paging file.Your system is running
low on virtual memory.Increase the virtual memory
by following the procedure
below.
1. Click Start, Settings,
then click Control Panel.
2. Double click the 
System
icon.
3. Click the Performance
tab.
4. ClickChange....
5. Increase the value of
Initial Size [MB] and
Maximum Size [MB].
6. Click Set.
7. Click OK.
8. Click Close.
9. Click Yesin the System
Settings Changedialog,
then restart your
computer.
If the same error message
appears after increasing the
virtual memory, increase it
more.
Error messagePossible causeRecovery
Perform the following
procedure.
1. Confirm that the
terminator is correctly set.
2. Confirm that the printer is
ready.
3. Confirm that the printer is
correctly connected with
a SCSI cable.
4. Turn off the computer,
then turn it on again.BCable connection is
improper or printer is
not ready.
BThe terminator setting
is improper. Error writing to “Port
name” for “Application
name”: The request could
not be performed
because of an I/O device
error. Do you wish to retry
or cancel the job? 
						

							139
BThe printer was
turned on after
turning on the
computer.
BThe terminator
setting is improper.
BSCSI setting or
cable connection is
improper. The necessary file is
not installed in the
computer.
Error messagePossible causeRecovery
Care and Maintenance
Not Detect. Turn off the printer and the
computer, then turn them
on again. If the trouble still
remains, confirm the
following points.
BThe terminator is
correctly set.
BThe SCSI board is
correctly installed in the
computer.
BThe system is correctly
connected with SCSI
cables.
BEach SCSI device has a
different ID Number. Invalid LPT Port.
SCSI board is not
correctly set.Correctly set the SCSI
board in the computer.
(Refer to the manual of the
SCSI board.) 
For any other trouble
related to SCSI, refer to
the SCSIsection of Care
and Maintenance 
( +P. 127). Unavailable LPT port is
selected when using
Windows 3.1.
No ASPI managers are
loaded. This typically
occurs when a DOS
ASPI manager is not
resident in memory.Reinstall the KX-P8410
software.
Select the other available
LPT port by following the
procedure below.
1. Double click the Main
icon.
2. Double click the Control
Panelicon.
3. Double click the Printers
icon.
4. Click Connect....
5. Click the other port, then
click OK.
6. Click Close.
Load Library Error!,
File Open Error!or
Install Error!appears
and Status Display does
not appear.
Status Display
ASPI for Win 16 or 32
could not properly
initialize itself. This may
be caused by a lack of
system resources.Lack of system
resources, or other
trouble related to
SCSI.Close some application
and retry. For any other
trouble related to SCSI,
refer to the SCSIsection of
Care and Maintenance 
( +P. 127). 
						

							140
Confirm that the SCSI
board is correctly installed
in the computer and it is
set correctly. (Refer to the
manual of the SCSI
board.) 
For any other trouble
related to SCSI, refer to
the SCSIsection of Care
and Maintenance 
( +P. 127). SCSI board is not set
correctly.
Unavailable LPT port is
selected when using
Windows 3.1. There isn’t available
LPT Port.
Error messagePossible causeRecovery
Care and Maintenance
SCSI device can not be
used. Because ASPI dll
file is not exist or
doesn’t match.SCSI board is not
installed correctly in
the computer and/or it
is not set correctly. This ASPI manager
does not support this
mode of Windows. You
typically see this error
code when running
Windows in Real ModeSCSI board is not set
correctly.Restart Windows in
Enhanced mode.
Select an available LPT
port by following the
procedure below.
1. Double click the Main
icon.
2. Double click the Control
Panelicon.
3. Double click the Printers
icon.
4. Click Connect....
5. Click the other port, then
click OK.
6. Click Close.
One or more ASPI for
DOS managers are
loaded which do not
support ASPI for Win16
or 32.Correctly set the SCSI
board in the computer.
(Refer to the manual of the
SCSI board.) 
For any other trouble
related to SCSI, refer to
the SCSIsection of Care
and Maintenance 
( +P. 127).