Panasonic 8410 Operating Instructions Manual

131
Communication cannot
be established between
the printer and your
computer.Install a media tray with
media in it.
Media Tray 
Empty All Media Tray
missing or empty
Fuser Unit and Oil Roll
Worn outCall for service. Lower Tray
Empty
Corrective ActionError Message
Care and Maintenance
Possible Cause
Paper Tray
Empty
Transparency Tray
Empty
Output Tray
Full
SIMM Check Error
SCSI error
Ethernet Card
Check Error
Imaging Unit
Worn out
Imaging Unit wearing out
Transfer wearing out
Fuser Unit wearing out
Oil...

132
The printer is too hot or
room temperature is
too high to print Labels. Cyan Toner
Empty
Error Message
Too hot to print Label
Remove Label, Cancel jobCorrective Action
Yellow toner cartridge
is almost empty. Yellow toner cartridge
is empty.
Care and Maintenance
Possible Cause
Low Black Toner
Low Cyan Toner
Low Magenta Toner
Low Yellow TonerBlack toner cartridge is
almost empty.
Cyan toner cartridge is
almost empty.
Magenta toner
cartridge is almost
empty.
Yellow Toner 
EmptyReplace the yellow
toner...

133
Close all applications
and turn off the
computer, then turn it
on again. An illegal error has
occurred. KX-P8410 or Printer Driver
is illegal condition. Abort
printing.
Error messagePossible causeRecovery
Care and Maintenance
Reinstall the KX-P8410
software. 1/16 compression table
is not found.
Check the cable
connection of the
printer or turn on the
printer. The printer connected
with the parallel cable
is not recognized. Block 16 table open error:
Table file not open!
BReprint later when
the...

134
Turn off the printer and
the computer, then turn
them on again. Print the
document again. SCSI Error!! Time Out
occurred.
Unable to Allocate Memory The computer’s
internal memory for
printing is insufficient. The printer is not
responding.
Error messagePossible causeRecovery
Care and Maintenance
*.DLL not found *.DLL function Error The necessary file for
printing is not found.Reinstall the KX-P8410
software.
nSome application settings may take priority over the printer driver settings.BClose all...

135
Correctly install the
SCSI board and its
driver. (Refer to the
manual of the SCSI
board.)
wnaspi32.dllwill be
installed or replaced
with a new version.
For any other trouble
related to SCSI, refer to
the SCSIsection of
Care and Maintenance
( +P. 127).
The ASPI manager
installed on this PC does
not support Windows.
Install ASPI for Windows.
[e.g. install wnaspi32.dll to
your windows (system
directory)]. The ASPI for Windows
installed on this PC does
not support expected
mode. Install newer version
of...

136
BClose all applications
except for the one which
controls the printer, then
print it again.
BTurn off the computer,
then turn it on again.
Print the document
again. Follow the procedure
below to make the setting
active.
1. Click Start, select
Settings, then click
Printers.
2. Click the Panasonic 
KX-P8410 printericon.
3. Click the File menu,
then click Properties.
4. Click Details tab and
Spool settings....
5. Click Enable bi-
directional support for
this printer, then click
OK.
Error messagePossible...

Error writing to
KXP8410GDI: for : The printer command
is invalid. Do you wish to
retry or cancel the job?
137
Care and Maintenance
Error messagePossible causeRecovery
Can not initialize ASPI for
Windows. Install newer
version of ASPI for
Windows.SCSI Board and its
driver are not installed
correctly.Correctly install SCSI board
and its driver. (Refer to the
instructions manual of the
SCSI board.)
Wnaspi32.dll will be
installed or replaced with a
new version.
For any other trouble related
to SCSI, refer...

138
Care and Maintenance
System Process-Out of
Virtual Memory 
Your system is running
low on virtual memory.
Please close some
applications. You can
then start the System
option in the Control
Panel and choose the
Virtual Memory button to
create an additional
paging file or to increase
the size of your current
paging file.Your system is running
low on virtual memory.Increase the virtual memory
by following the procedure
below.
1. Click Start, Settings,
then click Control Panel.
2. Double click the...

139
BThe printer was
turned on after
turning on the
computer.
BThe terminator
setting is improper.
BSCSI setting or
cable connection is
improper. The necessary file is
not installed in the
computer.
Error messagePossible causeRecovery
Care and Maintenance
Not Detect. Turn off the printer and the
computer, then turn them
on again. If the trouble still
remains, confirm the
following points.
BThe terminator is
correctly set.
BThe SCSI board is
correctly installed in the
computer.
BThe system is correctly...

140
Confirm that the SCSI
board is correctly installed
in the computer and it is
set correctly. (Refer to the
manual of the SCSI
board.) 
For any other trouble
related to SCSI, refer to
the SCSIsection of Care
and Maintenance 
( +P. 127). SCSI board is not set
correctly.
Unavailable LPT port is
selected when using
Windows 3.1. There isn’t available
LPT Port.
Error messagePossible causeRecovery
Care and Maintenance
SCSI device can not be
used. Because ASPI dll
file is not exist or
doesn’t match.SCSI board...