Panasonic 3 Ccd Color Camera Ccu Gp Us932cu Operating Instructions

21
Important:
• In the case of the following, --- appears and gamma
adjustment is not available.
• When BLACK STRETCH is set to ON
• When D-RANGE is set to EXPAND
[KNEE]  Adjusts the knee point.
Be sure to view a waveform monitor or a color video monitor
when the knee point adjustment is performed.
The knee point adjustment is selectable from the following.
MANU (default):The knee point is manually adjusted.
AUTO:The knee point is automatically adjusted.
When MANU is selected, follow the steps below to...

Note:
• Every time the [SEL] button is pressed, the size of the
rectangle cursor changes in the order of large →medi-
um →small.
Select a size to meet the photographic subject size.
xHold down the [MENU] button for more than 2 seconds.
→The MATRIX screen appears again.
cTo perform fine tuning, adjust GAIN (chroma) and
PHASE (hue).
For example, the adjustment of PHASE or GAIN of
R/R-Ye on the following screen provides the simultane-
ous adjustment of PHASE or GAIN of the adjacent
axes R and R-Ye in Color...

23
8. White balance setting [WHITE BAL]
The white balance adjustment is selectable from the follow-
ing.
AWC (default):The automatic white balance control mode
is activated. This adjustment is suitable for a location
where a light source is stable.
When AWC is selected, the operation to adjust the
white balance is required.
ATW:Activates the automatic white balance tracking mode.
The camera continuously measures the white balance
and automatically performs adjustment.
If the situation meets one of the...

24
10. Synchronization setting [SYNC]
The synchronization state is displayed. The horizontal
phase in the external synchronization can also be adjusted.
The internal synchronization is indicated as INT, and the
external synchronization is indicated as EXT.
The horizontal phase in the external synchro-
nization is adjusted.
zSet the synchronizing signal input/output selection
switch on the rear face of the CCU to IN.
xConnect the video synchronizing signal to the synchro-
nizing signal output/input...

The SEL menu is a simplified menu that can be called up
by pressing the [SEL] button while an image is displayed.
The following items can be set with use of the SEL menu.
•Image level [BRIGHTNESS]:Adjusts the brightness
(ELC, gain (AUTO), and the convergence level of elec-
tronic sensitivity enhancement (AUTO)). 
•Red level [R-GAIN]:Adjusts the red level.
•Blue level [B-GAIN]:Adjusts the blue level.
•Edge enhancement level [DTL-LEVEL]:Adjusts the
edge enhancement level.
•Electronic zoom [ZOOM]:Adjusts...

• Is the camera cable appropriately connected at both the
connector of the CCU and the connector of the camera
head? 
Check whether the connection is appropriately established.
9 • Pressing once displays the state. 
Press the [GAIN] button repeatedly until your target LED
lights. 
9
26
• Are the cables appropriately connected to the video output
connector, S-VIDEO output connector, RGB/YPbPr output
connector, HDMI output connector, or SDI output connec-
tor, respectively?
Check whether each cable is...

• Try to change the setting of DTL MODE.
27
20 • Is the lens aperture appropriately adjusted? 
Check whether the aperture is appropriately adjusted. 
Use lenses with recommended F number or higher and
3CCD-specific lenses.
Symptom
Blurred screen
Plural edges visible
AWC OK not displayed
Black bars at right and left of
image
Vertically longer image
No sound from monitor
• When the screen is too bright, narrow the lens aperture or
set ELC to ON.
• This phenomenon depends on the specifications of the...

28
GP-US932CU/GP-US932CUS
Power source: 12 V DC
Power consumption: 15 W (excluding camera head)
Pick-up system: Micro prism system
Image sensor: 1/3 3CCD, interline transfer (IT) equipped (progressive scanning supported)
Synchronization: Internal or external synchronization
Video output: Video output: BNC Connector x1, 1.0 V[P-P]/75 Ω
S-video output: S-video connector x1
Y: 0.714 V[P-P]/75 Ω
C: 0.286 V[P-P]/75 Ω
RGB/YPbPr output: D-sub 9-pin connector x1
R, G, B: 0.7 V[P-P]/75 Ω
Y: 0.7 V[P-P]/75 Ω
Pb,...

29
GP-US932CUE/GP-US932CUSE
Power source: 12 V DC
Power consumption: 15 W (excluding camera head)
Pick-up system: Micro prism system
Image sensor: 1/3 3CCD, interline transfer (IT) equipped (progressive scanning supported)
Synchronization: Internal or external synchronization
Video output: Video output: BNC Connector x1, 1.0 V[P-P]/75 Ω
S-video output: S-video connector x1
Y: 0.7 V[P-P]/75 Ω
C: 0.3 V[P-P]/75 Ω
RGB/YPbPr output: D-sub 9-pin connector x1
R, G, B: 0.7 V[P-P]/75 Ω
Y: 0.7 V[P-P]/75 Ω
Pb, Pr:...

30
GP-US932CU/GP-US932CUS
Operating Instructions (This document)  .............................................................. 1 pc.
Warranty Card for U.S. Field  ................................................................................ 1 pc.
GP-US932CUE/GP-US932CUSE
Operating Instructions (This document)  .............................................................. 1 pc.
Standard Accessories
GP-US932CU/GP-US932CUS
3CCD Color Camera Head GP-US932H
3CCD Color Camera Cable GP-CA932/4
3CCD...