Orion Pdp Opm 4240 Users Manual

38
OPM-4240 / OPM-4240R
39
Infinitely Expandable 
Go to "Control" in menu bar → PC Tracking → Auto in order to run "Tracking Auto" window.   y
  
In case alignment doesn't work through "Tracking Auto" command,  y
users can tune finely through "Tracking Manual". Go to "Control" of 
menu bar → PC Tracking → Manual or press "Ctrl+M" using keyboard.
"Tracking Manual" window enables users to set Frequency, Phase,  y
LineStart and PixelStart.
When...

40
OPM-4240 / OPM-4240R
41
Infinitely Expandable 
5.14. BiC Control
You can control BIC functions related with burn-in compensation.  y
Please select "Menu → Control → BIC Control" or "Ctrl+B" to start BIC control. y
Select one of BIC mode, BYPASS mode, REGENERAION mode and ANTI IMAGE STICKING mode and  y
click “EXE” to control Burn-in compensation function.	
	
	
	
	
	
	
	
1.BICOn/Off
BiC Mode:1)   
Activate BIC function to reduce burn-in effect. (BIC function On)
BYPaSS Mode:2)...

42
OPM-4240 / OPM-4240R
43
Infinitely Expandable 
Phosphor Update function changes phosphor value.  y
If you cannot have satisfactory compensation result by adjusting Deterioration function, you can change 
phosphor value.  
 
 
 
 
 
 
Deterioration function adjusts deterioration range for Red, Green and Blue respectively.  y
Set up Test pattern-Red, Green, Blue and "SCREEN" external image source, to control Deterioration.1) 
Adjust Deterioration range for Red, Green and Blue respectively.  2)...

44
OPM-4240 / OPM-4240R
45
Infinitely Expandable 
How to Control BiC  
1.MSCS
1) MSCS and MPDP must be always connected.
2)  If MSCS command is executed prior to the BIC command, the BIC command will be executed again 
one hour later.  
3) Turn off the energy save mode of the computer.
4)  The compensation for undesirable burn-in effect is made automatically when BIC function is executed. 
If the compensation result is not satisfactory, use additional Burn-in compensation function in MSCS. 
(Please see...

46
OPM-4240 / OPM-4240R
47
Infinitely Expandable 
MF-Controller configuration method 
1. Connect power.
2. Connect female D-sub to the Com port in a computer.
3. Connect male D-sub to the RS-232C port in MPDP.
4.  Set the number of the connected MPDP units in advance. The number can be set only by the Remote 
controller.
5. Set the switch at REMOCON side
DC 5~9V
BOOSTER REMOCONTO PDP
FROM PC
아답터 연결잭(5V 1A 사용)  MPDP연결PC연결
BOOSTER 또는 REMOCON 선택 스위치
※note
Select BOOSTER for a booster and BIC functions....

48
OPM-4240 / OPM-4240R
49
Infinitely Expandable 
8. Press "UP" and "DOWN" buttons to begin vertical configuration.(▲▼) 
 
Press the button for the number of the MPDP units and the same number of LEDs are turned on from 
the right side. (In case of 2X2, press    button.)
2sets are selected.
9. Press "GO" button to finish configuration mode. (Configuration finish & save)
10.   The rightmost LED (T.P.) is turned on when MF Controller starts BIC communication. If this LED 
blinks,...

50
OPM-4240 / OPM-4240R
51
Infinitely Expandable 
Introduction1. 
This document contains the communication protocol between PDP and its control devices such as computer for better 
use of the product. However, it does not include detailed technical matters. It rather focuses on t\
he brief functional 
explanation and communication protocol.
ID:1
Controller Tx/Rx Line ID:2ID:N-1ID:N
ID:N+1 ID:N+N
ID:(M-2)N+1 ID:(M-2)N+N
ID:(M-1)N ID:(M-1)N+2 ID:(M-1)N+N-1ID:MXN
※	Connection	formation	can	be	vary	based	on...

52
OPM-4240 / OPM-4240R
53
Infinitely Expandable 
Multi-Scale3.3. 
Screen expansion command for MPDP -Command Code  -0xDD (DVI), 0xDE (PC), 0xDF (DTV), 0xE0 (DVD), 0xE1(S-Video), 0xE2 (Video)One way communication (Send to PDP) -Data: ID (1 byte) +X/Y(1 byte) + P(1 byte)  -X: the number of horizontally installed MPDP Y: the number of vertically installed MPDP P: the location of expanded scaleX/Y: upper position 4bits - X (Max: 15), lower position 4bits - Y (Max: 15)e.g.)  0x44 for 4 x 4 screens, 0xFF for...

54
OPM-4240 / OPM-4240R
55
Infinitely Expandable 
Tracking Mode3.9. 
Automatic	or	Manual	screen	alignment	or	open	previous	configuration	at	PC	RGB	Mode. -Command Code:  -0x4A (Auto-tracking), 0x4B (Get Tracking Values), 0x4C (Frequency- tracking), 0x4D (Phase-tracking), 0x4E (Line-Start tracking), 0x4F (Pixel-Start tracking)Protocol format for each command  -:Get Tracking Values - Two way communication (Send to PDP, Receive from PDP)①SendtoPDP
STXCMDLengthIDETX
1 byte1 byte1 byte1 byte1 byte...

56
OPM-4240 / OPM-4240R
57
Infinitely Expandable 
Elapsed Time3.14. 
Command	for	finding	out	how	long	the	set	was	actually	used.	 -Command code: 0x78 -Protocol Format: - two way communication (Send to PDP, Receive from PDP) -*SendtoPDP
STXCMDLengthIDETX
1 byte1 byte1 byte1 byte1 byte
Data:  ID(1 byte) -*ReceiveFromPDP
STXCMDLengthDataCheck SumETX
1 byte1 byte1 byte7 byte1 byte1 byte
Data:  ID(1 byte) + Elapsed Time Data(5 byte) -Elapsed Time Data  -Data 0: position for hundred...