Optoma Tx765w Projector User Manual

							 
14
5.2 System Status 
 
Click [System Status] to shows current system status. 
Model Name: Product model name 
Versions:  
1. Firmware version no.: Wireless module firmware version number. 
Network Status: 
1. IP address: IP address of Wireless module. 
2. Subnet Mask: subnet mask 
3. Default Gateway: IP address of default gateway 
4.  Wireless MAC address: wireless MAC address 
Connection Status:  
1. Projecting status: either “Waiting for projecting” or “Projecting” 
2. Total Users
: It shows how many users login into Wireless Projector box. 
 
5.3 Network Setup 
There are many kinds of operating configurations as below.  
						

							 
15
 
< 
Auto-Configuration Network Setup> 
The default setting of the Wireless Projector box is DHCP client. When the 
Wireless Projector box is connected to a LAN that already has a DHCP server 
present, the 
Wireless Projector box takes an IP address assigned to it by the 
server. When the 
Wireless Projector box is connected to a LAN that does not 
have a DHCP server, the 
Wireless Projector box becomes the DHCP server in 
the network.
 
< IP Setup> 
  You can select “obtain IP address automatically” or “Use the following IP   
address” 
 IP Address: The default value is 192.168.100.10. 
  Subnet Mask: The default value is 255.255.255.0 
 Default Gateway: The default value is 192.168.100.10 
 
  You can select “auto(Enable/Disable DHCP Server” or “Disable”) 
  Start IP: The start IP address of DHCP Server.  
						

							 
16
  End IP: The end IP address of DHCP Server. 
< Wireless Setup> 
  Region: default value is “Worldwide”. 
  SSID: SSID string, max. Length is 32 bytes.  
  Channel: to set fixed channel or Auto. The “Auto” means after power 
on Wireless Projector, it will scan all of wireless channel and select 
clear one channel automatically. 
  WEP: you can Disable WEP key or select one of 64bit or 128bit in 
ASCII or HEX string. 
  Key: If WEP is enabled, you have to set key value according to WEP 
mode you selected.  
< Gatekeeper> 
Gatekeeper is designed for ensuring the enterprise network security within 
Wireless Projector box  
  All Block can block Guest Users(through wireless) to access all office 
network(LAN),  
  All Allow can pass Guest Users(through wireless) to access all office 
network  
  Internet Only can block Guest Users (through wireless) from office 
network (LAN) but still reserve internet connection capability. 
 
: press button to select this mode 
: press button to abort action. 
: Back to Operating mode main menu  
						

							 
17
5.4 Projection Setup 
 
Click [Projection Setup] button  
 
 : 1024*768, 1280x768 and 800*600.  
 : provide Wireless Projector output with 16bit or 32 
bit color depth.  It depends on your PC settings. 
 : This is VGA output refresh rate, provides 
both 60 Hz and 75Hz.  
 : You can select “Disable”, “Random”, or “Use the 
following code” to set a specific 4-digit number.  
 ：Confirm and Save modifications 
 : Cancel all the modifications 
  
						

							 
18
5.5 Change Passwords 
 
Click [Change Password] button, to change password. 
 
 : enter new password you want to change 
for each category. 
 : double check new password. 
 : Confirm and Save modifications. 
5.6  Reset to Default 
 
Click [Reset to Default] button to restore factory default settings. 
: Confirm reset.   
						

							 
19
 
*** Another way to restore Factory Default Settings, follow the procedure 
below: 
1) Press [Reset] button and Hold.  
2)  Turn on Wireless Projector box.  
3)  Wait for over 10 seconds and release [Reset] button. 
4)  It will take effect to restore factory default settings.  
 
 
5.7 Firmware Upgrade 
 
Click [Firmware Upgrade] button to upgrade firmware.  
 
  
						

							 
20
1)  Ensure you have acquired the latest firmware to download. 
2) Click  to specify file name you want to upgrade. 
3) Click  button to upgrade the firmware. 
4)  A warning message with the estimated time for completion will appear 
on the screen. 
5)  After a few minutes, a “complete” message will be shown on the 
screen.  
6)  Upon the completion of firmware upgrade, manually power off the 
projector and on again.  
 
 
 
 Warning:  DO NOT power off Wireless Projector while firmware upgrade 
is in progress. This will cause the wireless projector to fail and recovery 
process cannot be performed.   
						

							 
21
5.8  Projection Control Panel 
 
5.9 Alert Setting 
This option can be used to automatically send email alerts regarding various 
warning functions of the projector, including email alerts.  
						

							 
22
 
5.10  Reboot System 
 
Click [Reboot System] button to restart system 
 
: Restarts the system automatically. 
5.11  Logout 
Click [logout] to return back to the Web homepage.  
						

							 
23
6.   Mobishow 
6.1  Install from CD 
1)  Connect your personal portable device to PC. For example, if the 
operating system is Windows Mobile (v5.1 or above), please ensure it is 
connected in ActiveSync. 
2)  Copy the Mobishow *.CAB installation file from the User manual CD to 
your mobile device. 
3)  Run the installation file from your device operating system using “File 
explorer” and follow the on-screen instructions. 
4)  When prompted, check the screen of your device to finish installation on 
your portable device. 
 
6.2  Using MobiShow with a Personal Portable 
Device/Smart phone 
1) Open “Programs” on your device and find “MobiShow” application. 
2) Select “MobiShow” icon 
 to launch the client software.  
3)  MobiShow will turn on Wi-Fi on your device and list available access 
points for you to choose.