Optoma Projector Tx635 3d User Manual

							61English
User Controls
2-1.  Click the button  to enter Connect and Search Menu.
2-1-1.   Enter IP address of projector, select the option “Directly”, 
and then click “Connect” button to enter log-in interface; or 
Click “Search” button to search the projectors on network 
and select projectors to connect.
 
2-1-2.  Input “User type” and “Password” in log-in interface.
2-1-3.  
After log-in, Optoma Presenter will modify PC resolution to 
Network Application supported resolution.
2-2.  Click the button  to select the size of projection region, 
including Full screen and Alterable mode.
•  
Alterable size mode: The frame in ALTERABLE mode can be en- 
						

							62English
User Controls
larged or downsized by dragging the eight small black squares 
scattered on eight edges of the frame.
2-3.  Click the button  to select the language, Audio out and 
display the software information.
2-4.  Click the button  to control all the users and all the projec-
tors connected to the same projector.
 
•  : Display range.
•  : Click to unlock and change the network display password. 
Only the Administrator has rights to make the changes.
•  : When normal user login, click this lock icon will result in no 
response.
•  : Disconnect with target network display.
•  : Connect the target network display via a webpage front end.
•  : Turns on the audio.
•  : Turns off the audio.
User of Admin type is able to view a menu page with a list of PCs 
connected to the target network display.
	Audio transfer is sup-ported in one on one connection between pc and computer. When audio out is enabled, video image quality setting will be greyed out.
	To get the higher image quality, please set quality to high, and set audio out to “No”.  
						

							63English
User Controls
 
•  : For the other PCs.
•  : For the current PC.
•  : Options of display port in which 
the highlight one is the current status, click on one of them to 
change the display port.
•  : Disconnect the PC from a network display.
	The quality of the image via network connection depends upon total bandwidth available in the net-work. 
						

							64English
Appendices
 No image appears on-screen
 Ensure all the cables and power connections are correctly and 
securely connected as described in the “Installation” section.
 Ensure all the pins of connectors are not bent or broken.
 Check if the projection lamp has been securely installed. Please 
refer to the “Replacing the lamp” section.
 Make sure you have removed the lens cap and the projector is 
switched on.
 Ensure that the “AV mute” feature is not turned on.
 Partial, scrolling or incorrectly displayed image
 Press “Re-SYNC” on the remote.
 If you are using a PC:
 For Windows 95, 98, 2000, XP, Windows 7:
1.  Open the “My Computer” icon, the “Control Panel” folder, and 
then double click on the “Display” icon.
2. Select the “Settings” tab.
3. Verify that your display resolution setting is lower than or equal 
to UXGA (1600 × 1200).
4. Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will also 
need to change the monitor display you are using. Refer to the 
following steps.
5. Verify the resolution setting is lower than or equal to UXGA 
(1600 × 1200).
 6.  Select the “Change” button under the “Monitor” tab.
Troubleshooting
 If you experience a problem with your projector, 
please refer to the following information. If a 
problem persists, please contact your local  
reseller or service center.  
						

							65English
Appendices
 7.  Click on “Show all devices”. Next, select “Standard monitor 
types” under the SP box; choose the resolution mode you need 
under the “Models” box. 
 8.  Verify that the resolution setting of the monitor display is lower 
than or equal to UXGA (1600 × 1200). 
 If you are using a Notebook:
 1.  First, follow the steps above to adjust resolution of the  
computer.
 2.  Press the appropriate keys listed below for your notebook 
manufacturer to send signal out from notebook to projector. 
Example: [Fn]+[F4]
  
 
 If you experience difficulty changing resolutions or your monitor 
freezes, restart all equipment including the projector.
 The screen of the Notebook or PowerBook computer is not 
displaying your presentation
 If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens when a 
second display device is in use. Each has a different way to be  
reactivated. Refer to your computer’s manual for detailed  
information.
 Image is unstable or flickering
 Use “Phase” to correct it. See page 37 for more information.
 Change the monitor color setting on your computer.
 Image has vertical flickering bar
 Use “Frequency” to make an adjustment. See page 37 for more 
information.
 Check and re-configure the display mode of your graphic card to 
make it compatible with the projector. 
Acer    [Fn]+[F5]
Asus   [Fn]+[F8]
Dell    [Fn]+[F8]
Gateway  [Fn]+[F4]
Mac Apple: System Preference  Display  Arrangement  Mirror display
IBM/Lenovo  [Fn]+[F7]
HP/Compaq  [Fn]+[F4]
NEC     [Fn]+[F3]
Toshiba    [Fn]+[F5] 
						

							66English
Appendices
 Image is out of focus
 Make sure the lens cap is removed.
 Adjust the Focus Ring on the projector lens. 
 Make sure the projection screen is between the required distance. 
See page 17.
 The image is stretched when displaying 16:9 DVD title
 When you play anamorphic DVD or 16:9 DVD, the projector will 
show the best image when the projector display mode is set to 
16:9 in the OSD.
 If you play 4:3 format DVD titles, please change the format to 4:3 
in the projector OSD.
 If the image is still stretched, you will also need to adjust the 
aspect ratio by referring to the following:
 Please setup the display format as 16:9 (wide) aspect ratio type 
on your DVD player.
 Image is too small or too large
 Move the projector closer to or further from the screen.
 Press “Menu” button on the remote control or projector panel, go 
to “DISPLAY  Format” and try the different settings.
 Image has slanted sides
 If possible, reposition the projector so that it is horizontally 
centered on the screen and below the bottom of the screen.
 Press “Keystone +/-” button on the remote control or press  
“ / ” on the projector panel, until the sides are vertical.
 Image is reversed
 Select “SETUP  Projection” from the OSD and adjust the  
projection direction. 
						

							67English
Appendices
 The projector stops responding to all controls
 If possible, turn off the projector, then unplug the power cord and 
wait at least 60 seconds before reconnecting power.
 Check that “Keypad Lock” is not activated by trying to control the 
projector with the remote control.
 Lamp burns out or makes a popping sound
 When the lamp reaches its end of life, it will burn out and may 
make a loud popping sound. If this happens, the projector will not 
turn on until the lamp module has been replaced. To replace the 
lamp, follow the procedures in the “Replacing the Lamp” section on 
pages 69-70.
 LED lighting message
Steady light    
No light  
MessagePOWER/STAND-BY LEDTemp-LEDLamp-LED
(Green/Amber)(Red)(Red)
Standby State
(Input power cord)Amber
Power on (Warming)Flashing Green
Lamp lightingGreen
Power off (Cooling) Flashing Green
Quick Resume(100 secs)Flashing Green
Error (Over Temp.)Flashing Amber
Error (Fan fail)Flashing AmberFlashing
Error (Lamp fail)Flashing Amber
＊  POWER/STANDBY LED be ON when OSD appears, be OFF when OSD disappears.                      
						

							68English
Appendices
 On Screen Messages 
 Temperature warning:
 
 Fan failed:
 
 Lamp warning:
 
 Out of display range:
 
 If the remote control does not work
 Check the operating angle of the remote control is within ±15° both horizontally and vertically of one of the IR receivers on the projector.
 Make sure there are not any obstructions between the remote control and the projector. Move to within 7 m (±0°) of the projector.
 Make sure the batteries are inserted correctly.
 Replace batteries if they are exhausted. 
						

							69English
Appendices
Replacing the lamp
The projector automatically detects the lamp life. When the 
lamp life is nearing the end of use, you will receive a warning 
message.
When you see this message, please contact your local reseller 
or service center to change the lamp as soon as possible. 
Make sure the projector has been cooled down for at least 30 
minutes before changing the lamp. 
 Warning: Lamp compartment may be hot! Allow it to cool 
down before changing the lamp!
 Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shat-ter and cause injury if it is dropped.
 Warning: If ceiling mounted, please use caution when  
opening the lamp access panel. It is recommended to wear 
safety glasses if changing the bulb when ceiling mounted. 
“Caution must be used to prevent any loose parts from fall-
ing out of projector.”  
						

							70English
Appendices
Lamp Replacement Procedure:
1. Switch off the power to the projector by pressing the “” button. 
2. Allow the projector to cool down for at least 30 minutes.
3. Disconnect the power cord.
4. Unscrew the one screw on the cover. 1
5. Lift up the cover. 2
6. Unscrew the two screws on the lamp module. 3
7. Lift up the lamp handle 4 and remove the lamp module slowly and carefully. 5
To replace the lamp module, reverse the previous steps.
8.   Turn on the projector and use “Lamp Reset” after the lamp module is  replaced.
Lamp Reset: (i) Press “Menu”  (ii) Select “OPTIONS”  (iii) Select  “Lamp Settings”  (iv) Select “Lamp Reset”  (v) Select “Yes”.
	The screws on the lamp cover and the lamp cannot be removed.  	The projector cannot be turned on if the lamp cover has not been 
placed back on the projector.  	Do not touch the glass area of the lamp. Hand oil can cause the lamp to shatter. Use a dry cloth to clean the lamp module if it was accidentally touched.1
2
3
4
5