Optoma Projector Tx635 3d User Manual

							51English
User Controls
 Projector Control
This selection gives you access to most of the settings available in 
the projector and the current configuration without having to be in 
the same room.
 Alert Setup
•  
Alert Type:This selection allows the admin to receive alerts when 
the projector is at fault.
•   SMTP setting and Email setting:This page is to set up the details 
of mail sending, ex. mail server IP address, user name, password 
and mail address of receivers. (Note: Multi-receivers are sepa-
rated by semicolon.)
  Network Setup
This page is for setting up and configuring the wireless usb dongle.  
						

							52English
User Controls
•  IP Setup: Click “Obtain an IP address automatically” as auto 
mode; click “Use the following IP Address” as static mode,  IP Ad-
dress/Subnet Mask/Default Gateway/ DNS Server are required to 
be filled and then click “Apply” button.
•  DHCP Server Setup: Enable/Disable, Start IP, End IP, Subnet 
Mask, Default Gateway, DNS server.
•  Wireless Setup: This allows you to setup the projector as an 
access point or as a client that can be integrated to an existing 
network.
  Presenter Setup
Admin password/User password is used to change the password 
for admin/user in target side.
Click “Connection Control” to enter “Connection Status” 
						

							53English
User Controls
•  Conference Control: Click “On” or “Off” to enable/disable confer-
ence control mode.
 Click the following icons under “Play Control”
•  : Click to disconnect host PC.
•  : Click to switch session to background.
•  : Click to change display region.
  Crestron RoomView
This is the control page of Flash UI.
Click “Power” to control power on/off of projector.
Click “Vol-, Mute, Vol+” to control volume.
In the SourceList, it includes all sources that the projector can 
process. 
Click “Menu” to open menu; click “Source” to choose next source; 
click “Auto” to detect the source automatically; click “Blank” for  AV 
mute function.
“Contrast, Brightness, Color, Sharpness, Zoom, Freeze” can be 
adjusted in the control panel below.  
						

							54English
User Controls
Click “Tools”, the following items are included:
•  Crestron Control: the basic network information of the control 
system device.
•  Projector: the ID of each projector in a building for Administrator 
to control. 
•  User Password: change user’s password.
•  Default Language: set the default language.
•  DHCP: enable/disable DHCP and the details of network card.
•  
Admin Password: change administrator’s password.
After change each items, click “Send” button to make it effect.
Click “Info” to show information and status of this projector. 
						

							55English
User Controls
Click “Help” to inform administrator to do related protection or 
operation.
 Reset to Default
Click “Apply” to reset system to the default settings. 
Click “Flash Upgrade” to upgrade the Firmware from USB disk, 
which has been inserted in projector.
 Reboot System
Click “Reboot” to reboot system. 
						

							56English
User Controls
How to use Multi-media Card Reader 
Application
The Card Reader application can display packaged images in a 
USB flash device. 
1. Plugging the USB device into USB port of projector, source of Flash 
Drive is detected, and then USB Flash Devices Detection Screen is 
displayed. It supports 3 USB devices at the same time.
2.  Press “Enter” to enter Thumbnail mode, different photos in differ-
ent folders can be  chosen;  If only one USB is plug-in, it will show 
thumbnail list directly. The following buttons are supported in the 
user interface:
• : Go to the top level of the selected USB.
•  : Go to previous level of folder.
•  : Setup function.
•  : Select another USB
	If the file name is too long to show, it will show “…” on the last character beyond the limited length and cut out the spare string. 
						

							57English
User Controls
Press “Left” to back to the rightist at the same line; press “Right” 
to jump to next page; press “Up” to jump to previous page; press 
“Down” to jump to next page; press “Enter” into a picture, it will 
display picture auto fit to the screen by retaining original size ratio.
2-1.   Setup Menu 
When you highlight on  and press “Enter” button, enter 
into Setup menu. The following buttons are supported in the 
user interface:
•  Thumbnail Order: Enter the Thumbnail Display Mode.
•  Slideshow: Enter the Slide Show Mode.
  Timer: Use this function to set the slideshow interval.
  Effect: Show the effect of Slideshow.
  Repeat ON/OFF: Enable/Disable Slide Show Repeat Mode.
•  : Go back to thumbnail file browsing.
Press Up/Down/Left/Right key to choose different functions and 
press Enter key to make it effect.
2-2.    Slideshow 
When you press “Enter” into a picture, it will display picture 
auto fit to the screen by retaining original size ratio. The fol-
lowing buttons are supported in the user interface:
Slideshow Controls 
						

							58English
User Controls
•  : Slideshow On.
  Right /Left key: Show the next/previous photo and keep 
slideshow.
  Enter key: Show the controls bar.
  Menu key: Show the projector menu.
•  : Slideshow off.
  Up /Down key: Rotate +90/-90 degree.
  Right /Left key: Show the next/previous photo.
  Enter key: Show the controls bar.
  Menu key: Show the projector menu.
•  : Go back to thumbnail file browsing.
Press Left/Right key to choose different functions and press Enter 
key to make it effect.
2-3.    PDF 
When you press “Enter” into a PDF file, it will display PDF 
document as full mode. The following buttons are supported 
in the user interface:
 
  : Back to Thumbnail file browsing.
   
: Hidden setting bar.
   
: Fit/Full switch.
   
: Set page to previous 5 pages.
   
: Set page to next 5 pages.
   
: Directly jump to page that set in 
the previous column.
   
: Current/Total pages.
When the image cannot be displayed due to memory limitation or 
cannot support image format, the specific image is displayed on 
the center of the screen.
	When the image file is large, slide show time will be longer more than the general picture, such as BMP format. The max size of image file is as below:
- JPG:10000 x 10000;
- TIF, BMP, GIF and PNG: 1280 x 800 
						

							59English
User Controls
How to use the Optoma Presenter System
Optoma Presenter application allows a pc host to present from USB 
and via network connection (wired or wireless).
1-1.  Using Optoma Presenter via USB or Ethernet cable
 
Connect the usb cable to the projector. A USB device will be seen 
in “my computer”.
•  Select “Optoma Presenter”, and then run “autorun.exe” to start 
USB display.
•  Press the Autorun icon in the right-down region to pause or play 
the USB display.
1-2.   Using Optoma Presenter via mini Wifi USB dongle
1-2-1.   Insert mini Wifi USB dongle into projector’s USB port.
(S ER VIC E)C
Mini WiFi USB Dongle 
(Optional Accessory)
	This projector is only compatible with Optoma’s Mini WiFi USB Dongle. Please contact Optoma Service for details. 
	Mini WiFi USB dongle is optional accessory.
	USB Display and Network Display support Window XP, Vista, Win7, Win7 (32/64bit), Mac OS 10.5, Mac OS 10.6.
	Keyboard mouse function only sup-ports Network Display source. 
	User must be admin-istrator login. 
	Keyboard mouse function works at full screen or Left up screen or left screen.
	Keyboard mouse function will not work when logged out or in lock, sleep, hibernate or standby modes.          
						

							60English
User Controls
1-2-2.  Power on projector.
/
/
1-2-3.  Connect to Mini WiFi USB Dongle SSID “Network Display” 
from your PC device.
12
3
1-2-4.  Download and Install Optoma Presenter Software.
2. After installation in PC, double click the program of Optoma Pre-
senter to enter main window.
•  : Connect and search network display.
•  : Select display region.
•  : Manage all connected network displays.
•  : Configure Optoma Presenter.
	Default SSID for wireless is Network Display.