Optoma Projector Tx612 User Manual

English

Installation
Connecting	the	Projector
Connect	to	Computer/Notebook
.........................................................................\
...........................Power Cord2.........................................................................\
............................VGA Cable3.........................................................................\
.......................*RS232 Cable 4.........................................................................\...

2English

Installation

	Connect	to	Video	Sources
.........................................................................\
...........................Power Cord2.........................................................................\
............................VGA Cable 3.........................................................................\
.......*Composite Video Cable4........................................................................\
......................*S-Video...

3English

 Installation

	Powering	On/Off	the	Projector
	Turn on the projector fi rst and then select the signal sources.
Powering On the Projector
.  Remove the lens cap. 
2. Securely connect the power cord and signal cable. When 
connected, the ON/STANDBY LED will turn Amber. 
3.  Turn on the lamp by pressing “” button either on the top of 
the projector or on the remote. The ON/STANDBY LED will 
now turn Green. 
  The startup screen will display in approximately 0 seconds. 
The fi...

4English

Installation

	Contact the nearest service center if the projector displays these symptoms. See pages 53-54 for more information.
Warning Indicator
When the warning indicators (see below) come on, 
the projector will automatically shutdown: 
 “LAMP” LED indicator is lit red and if “On/Standby” indicator 
flashes amber.
  “TEMP” LED indicator is lit red and if “On/Standby” 
indicator flashes amber. This indicates the projector has 
overheated. Under normal conditions, the projector can...

5English

 Installation

 Adjusting	the	Projected	Image
Adjusting the Projector’s Height 
The	projector	is	equipped	with	elevator	feet	for	adjusting	
the	image	height.
. Locate the adjustable foot you wish to modify on the 
underside of the projector. 
2. Rotate the adjustable rings clockwise/anticlockwise to 
lower or raise the projector. Repeat with the remaining feet 
as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring 

6English

Installation
 This graph is for user’s reference only.
Adjusting the Projector’s Zoom / Focus
You may turn the zoom ring to zoom in or out. To focus the 
image, rotate the focus ring until the image is clear. 
 .x Zoom series will focus at distances from 4.92 to 32.8 
feet (.50 to 0.00 meters).
Adjusting Projection Image Size
Hd
57.7(146.4cm)
138.4(351.5cm)
184.5(468.6cm)
230.6(585.8cm)
276.7(702.9cm)
38.1(96.6cm)
63.4(161.1cm)
152.2(386.6cm)
202.9(515.5cm)...

7English

 User Controls
Control Panel
 Control Panel & Remote Control
AV MUTEPOWER
Using the Control Panel
PowerRefer to the “Power On/Off the Projector” section on 
pages 3-4.
RE-SYNCAutomatically synchronize the projector to the input 
source.
 EnterConfi rm your item selection.
SOURCEPress “SOURCE” to select an input signal.
MenuPress “Menu” to launch the on-screen display (OSD) 
menu. To exit OSD, Press “Menu” again.
AV MUTEMomentarily turns off/on the audio and video.
Four...

8English

User Controls

Remote Control
Using the Remote Control
Power  
Refer to the “Power On/Off the Projector” 
section on pages 3-4.
L ButtonMouse left click.
R ButtonMouse right click.
Page +Use this button to page up.
Page -Use this button to page down.
 EnterConfi rm your item selection.
SourcePress “Source” to select an input signal.
Re-SYNC Automatically synchronizes the projector to 
the input source.
Four Directional 
Select KeysUse     to select items or make 
adjustments to...

9English

 User Controls

Remote Control
Using the Remote Control
FreezePress “Freeze” to pause the screen image.
Press this button again to unlock.
AV muteMomentarily turns off/on the audio and 
video.
S-Video Press “S-Video” to choose S-Video source.
VGAPress “VGA” to choose VGA sources.
VideoPress “Video” to choose Composite video 
source. 

20English

User Controls

The	Projector	has	multilingual	On-screen	Display	menus	that	
allow	you	to	make	image	adjustments	and	change	a	variety	of	
settings.	The	projector	will	automatically	detect	the	source.	
How to operate 
.  To open the OSD menu, press “Menu” on the Remote Control or 
Projector Keypad.
2  When OSD is displayed, use   keys to select any item in the 
main menu. While making a selection on a particular page, press 
 or “Enter” key to enter sub menu.
3. Use   keys to select the...