Optoma Projector Tx612 User Manual
Here you can view all the pages of manual Optoma Projector Tx612 User Manual. The Optoma manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 41
4English Appendices Image is out of focus Make sure the lens cap is removed. Adjust the Focus Ring on the projector lens. Make sure the projection screen is between the required distance. See page 6. The image is stretched when displaying 6:9 DVD title When you play anamorphic DVD or 6:9 DVD, the projector will show the best image when the projector display mode is set to 6:9 in the OSD. If you play 4:3 format DVD titles, please change the format to 4:3 in...
Page 42
42English Appendices The projector stops responding to all controls If possible, turn off the projector, then unplug the power cord and wait at least 60 seconds before reconnecting power. Check that “Keypad Lock” is not activated by trying to control the\ projector with the remote control. Lamp burns out or makes a popping sound When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module...
Page 43
43English Appendices On Screen Messages Temperature warning: Fan failed: Lamp warming: Out of display range: Remote Control If the remote control does not work Check the operating angle of the remote control is within ±5° both horizontally and vertically of one of the IR receivers on the projector. Make sure there are not any obstructions between the remote control and the projector. Move to within 7 m (±0°) of the projector. Make sure the batteries are inserted...
Page 44
44English Appendices Replacing the lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp. Warning: Lamp compartment may be hot! Allow it to cool down before changing the lamp! Warning: To reduce the...
Page 45
45English Appendices Lamp Replacement Procedure: . Switch off the power to the projector by pressing the “” button. 2. Allow the projector to cool down for at least 30 minutes. 3. Disconnect the power cord. 4. Unscrew the two screws on the cover. 5. Lift up and remove the cover. 2 6. Unscrew the two screws on the lamp module. 3 7. Lift up the lamp handle and remove the lamp module slowly and carefully. 4 To replace the lamp module, reverse the previous steps. 8. Turn on the...
Page 46
46English Appendices Compatibility Modes ModeResolutionV-Sync (Hz)H-Sync (KHz) AnglogDigitalAnglogDigital VGA640 × 35070703.50 3.50 VGA640 × 350858537.9037.90 VGA640 × 400858537.9037.90 VGA640 × 48060603.50 3.50 VGA640 × 480727237.9037.90 VGA640 × 480757537.5037.50 VGA640 × 480858543.3043.30 VGA720 × 40070703.50 3.50 VGA720 × 400858537.9037.90 SVGA800 × 600565635.2035.20 SVGA800 × 600606037.9037.90 SVGA800 × 600727248.0 48.0 SVGA800 × 600757546.9046.90 SVGA800 ×...
Page 47
47English Appendices Video Compatibility Computer Compatibility ModeResolutionV-Sync (Hz)H-Sync (KHz) MAC LC 3”640 × 48066.6634.98 MAC II 3”640 × 48066.6835.00 MAC 6”832 × 62474.5549.73 MAC 9”024 × 7687560.24 MAC52 × 87075.0668.68 MAC G4640 × 48060 3.35 i MAC DV024 × 7687560.00 i MAC DV52 × 8707568.49 i MAC DV280 × 9607575.00 NTSCM (3.58MHz), 4.43 MHz PALB, D, G, H, I, M, N SECAMB, D, G, K, K, L SDTV/HDTV480i/p, 576i/p,...
Page 48
48English Appendices RS232 Commands and Protocol Function List RS232 Pin Assignments Pin no.Spec. (from projector side) N/A 2RXD 3TXD 4N/A 5GND 6N/A 7N/A 8N/A 9N/A 12345 6789
Page 49
49English Appendices RS232 Protocol Function ListOptoma EX612 RS232 Command Table. --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Baud Rate : 9600 Note : There is a after all ASCII commands Data Bits: 8 0D is the HEX code for in ASCII code Parity: None Stop Bits: 1 Flow Control :...
Page 50
50English Appendices --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ~XX60 1 7E 30 30 36 30 20 31 0D Format 4:3 ~XX60 2 7E 30 30 36 30 20 32 0D 16:9-l ~XX60 3 7E 30 30 36 30 20 33 0D 16:9-ll ~XX60 6 7E 30 30 36 30 20 36 0D Native ~XX60 7 7E 30 30 36 30 20 37 0D Auto...