Optoma Projector Tx610st User Manual

							41English
User Controls
SETUP | Advanced
 Logo
Use this function to set the desired startup screen. If changes are 
made they will take effect the next time the projector is powered 
on.
 Optoma: The default startup screen.
 User: Use stored picture from “Logo Capture” function.
  Logo Capture
Press   to capture an image of the picture currently displayed
on screen.
  Closed Captioning
Use this function to set the desired startup screen. If changes are 
made they will take effect the next time the projector is powered 
on.
 Off: select “off” to turn off the closed captioning feature.
  CC1:CC1 language: American English.
 CC2:CC2 language (depending on the TV channel of the 
user):Spanish, French, Portuguese, German, Danish.
	For successful logo 
capture, please 
ensure that the on-
screen image does 
not exceed the pro -
jector’s native resolu -
tion. (XGA:1024x768  
or WXGA:1280x800). 
						

							42
English
User Controls
SETUP | Network
  Network State
Display the network connection status.
 DHCP
Use this function to select your desired startup screen. If you 
change the setting from one to another, when you exit the OSD 
menu, the new setting will take effect on next open.
 On: Assign an IP address to the projector from an external 
DHCP server automatically.
 Off: Assign an IP address manually.
  IP Address
Select an IP address.
 Subnet Mask
Select subnet mask number.
 Gateway
Select the default gateway of the network connected to the 
projector.
  DNS
Select DNS number.
 Apply
Press “” and then choose “Yes” to apply the selection.  
						

							43English
User Controls
1. Turn on DHCP to allow the DHCP server to automatically assign 
an IP, or manually enter the required network information.
2. Then choose apply and press  “” button to complete the 
configuration process.
3.  Open your web browser and type in from the OSD LAN screen 
then the web page will display as below:
4. Open “ Control Panel ” to control your projector. 
 
When making a direct connection from your computer to the  projector
Step 1: Find an IP Address (192.168.6.74) from LAN function of  projector.
How to use web browser to control your projector
	When you used 
the projector IP 
address, you 
will can not link 
to your service 
server.        
						

							44
English
User Controls
Step 2: Select apply and press  “Enter” button to submit function or press “ menu” key to 
exit.
Step 3:  To open Network Connections, click  Start, click Control Panel, click Network 
and Internet Connections , and then click Network Connections. Click the 
connection you want to configure, and then, under  Network Tasks 
 , click 
Change settings of this connection .
Step 4: On the General tab, under  This connection uses the 
following items , click Internet 
Protocol (TCP/IP) , and then click 
“ Properties.”
Step 5: Click Use the following IP 
address, and type in as below:
1) IP address: 192.168.6.XXX 
2) Subnet mask: 255.255.0.0
3) Default gateway:192.168.6.254
Step 6:  To open Internet Options, click 
IE web browser, click Internet 
Options, click the Connections 
tab and click “ LAN Settings...” 
 Step 7: The Local Area Network (LAN) 
Setting dialog box appears , In the 
Proxy Server area , cancel the 
Use a proxy server for your LAN 
check box., then click “ OK” button 
twice.
Step 8: Open your IE and type in the IP  address of 192.168.6.74 in the 
URL then press “ Enter” key. The 
web page will display as below:
 
Step 9: Open “ Control Panel” to control 
your projector.             
						

							45English
User Controls
 Source Lock
 
On:  The projector will only search current input connection.
 Off: The projector will search for other signals if the current 
input signal is lost.  
 High Altitude
When “On” is selected, the fans will spin faster. This feature is 
useful in high altitude areas where the air is thin.
 Information Hide
 
On: Choose “On” to hide the info message.
 Off: Choose “Off” to show the “searching” message.
 Keypad Lock
When the keypad lock function is “On”, the control panel will be 
locked however, the projector can be operated by the remote 
control. By selecting “Off”, you will be able to reuse the control 
panel.
  Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or 
“White”, screen when no signal is available.
  Reset
Choose “Yes” to return the display parameters on all menus to the 
factory default settings.
OPTIONS
	 To turn off the key-
pad lock, press and 
hold “Enter” key on 
top of the projector 
for 5 seconds.
	With dust filter 
installed, High 
Altitude mode must 
be turned on. Dust 
filter is Optional and 
may not be required 
in some regions. 
						

							46
English
User Controls
OPTIONS | 
Advanced
  Direct Power On
Choose “On” to activate Direct Power mode. The projector will 
automatically power on when AC power is supplied, without 
pressing the “
” key on the projector control panel or on the 
remote control.
  Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, 
when there is no signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes).
 Sleep Timer (min)
Sets the countdown timer interval. The countdown timer will start, 
with or without a signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes).
 Power Mode (Standby)
 
Eco.: Choose “Eco.” to save power dissipation further < 1W.
 Active: Choose “Active” to return to normal standby and the  VGA out port will be enabled. 
	Eco (
						

							47English
User Controls
OPTIONS |   
Lamp Settings
  Lamp Hours
Display the projection time.
 Lamp Reminder
Choose this function to show or to hide the warning message 
when the changing lamp message is displayed.   
The message will appear 30 hours before suggested replacement 
of lamp.
  Brightness Mode
  
STD: Choose “STD” to dim the projector lamp which will lower 
power consumption and extend the lamp life. 
 BRIGHT: Choose “BRIGHT” to increase the brightness. 
  Lamp Reset
Reset the lamp hour counter after replacing the lamp.
	 When ambient tem -
perature is over 35 °C 
in operating, the 
projector will switch 
to STD automatically.
  
						

							48
English
Appendices
  No image appears on-screen
 
Ensure all the cables and power connections are correctly and 
securely connected as described in the “Installation” section.
  Ensure all the pins of connectors are not bent or broken.
 Check if the projection lamp has been securely installed. Please 
refer to the “Replacing the lamp” section.
  Make sure you have removed the lens cap and the projector is 
switched on.
  Ensure that the “AV mute” feature is not turned on.
 Partial, scrolling or incorrectly displayed image
 
Press “Re-SYNC” on the remote.
 If you are using a PC:
  For Windows 95, 98, 2000, XP, Windows 7:
1.  Open the “My Computer” icon, the “Control Panel” folder, and 
then double click on the “Display” icon.
2.  Select the “Settings” tab.
3.  Verify that your display resolution setting is lower than or equal 
to UXGA (1600 × 1200).
4.  Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will also 
need to change the monitor display you are using. Refer to the 
following steps.
5.  Verify the resolution setting is lower than or equal to UXGA 
(1600 × 1200).
  6.  Select the “Change” button under the “Monitor” tab.
Troubleshooting
 If you experience a problem with your projector, 
please refer to the following information. If a 
problem persists, please contact your local   
reseller or service center.  
						

							49English
Appendices
 7.  Click on “Show all devices”. Next, select “Standard monitor 
types” under the SP box; choose the resolution mode you need 
under the “Models” box. 
  8.  Verify that the resolution setting of the monitor display is lower 
than or equal to  UXGA (1600 × 1200). 
 If you are using a Notebook:
  1.  First, follow the steps above to adjust resolution of the   
computer.
  2.  Press the appropriate keys listed below for your notebook 
manufacturer to send signal out from notebook to projector. 
Example: [Fn]+[F4]
  
 
  If you experience difficulty changing resolutions or your monitor 
freezes, restart all equipment including the projector.
  The screen of the Notebook or PowerBook computer is not 
displaying your presentation
 
If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens when a 
second display device is in use. Each has a different way to be  
reactivated. Refer to your computer’s manual for detailed   
information.
  Image is unstable or flickering
 
Use “Phase” to correct it. See page 38  for more information.
 Change the monitor color setting on your computer.
 Image has vertical flickering bar
 
Use “Frequency” to make an adjustment. See page 38 for more 
information.
  Check and re-configure the display mode of your graphic card to 
make it compatible with the projector. 
Acer    
[Fn]+[F5]
Asus    [Fn]+[F8]
Dell    [Fn]+[F8]
Gateway   
[Fn]+[F4]
Mac Apple: 
System Preference  Display  Arrangement   Mirror 
displayIBM/Lenovo   [Fn]+[F7]
HP/Compaq   [Fn]+[F4]
NEC     [Fn]+[F3]
Toshiba      [Fn]+[F5] 
						

							50
English
Appendices
  Image is out of focus
 
Make sure the lens cap is removed.
 Adjust the Focus Ring on the projector lens. 
 Make sure the projection screen is between the required distance. 
See page 16.
  The image is stretched when displaying 16:9 DVD title
 
When you play anamorphic DVD or 16:9 DVD, the projector will 
show the best image when the projector display mode is set to 
16:9 in the OSD.
 If you play 4:3 format DVD titles, please change the format to 4:3 
in the projector OSD.
 If the image is still stretched, you will also need to adjust the 
aspect ratio by referring to the following:
 Please setup the display format as 16:9 (wide) aspect ratio type 
on your DVD player.
  Image is too small or too large
 
Move the projector closer to or further from the screen.
 Press “Menu” button on the remote control or projector panel, go 
to “DISPLAY   Format” and try the different settings.
 Image has slanted sides
 
If possible, reposition the projector so that it is horizontally 
centered on the screen and below the bottom of the screen.
  Press “Keystone +/-” button on the remote control or press  
“
 / ” on the projector panel, until the sides are vertical.
  Image is reversed
 
Select “SETUP 
 Projection” from the OSD and adjust the  
projection direction.
	 Use of Keystone 
is not recom-
mended.