Optoma Projector Tx610st User Manual

							21English
User Controls
 Using the HELP button
The HELP function ensures easy setup and operation.  
 Press the “?” button on the remote control or press the 
“HELP” button on the control panel to open the Help Menu.   
						

							22
English
User Controls
 Help menu button functions only when no input source 
is detected.
 If input source is detected and help button is pressed, the 
following pages will appear to help diagnose any problems.
	 Please refer to the 
“Troubleshooting” 
section on pages 
48-52 for more 
details . 
						

							23English
User Controls 
						

							24
English
User Controls
The Projector has multilingual On-screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1.  To open the OSD menu, press “Menu” on the Remote Control or 
Projector Keypad.
2  When OSD is displayed, use
   keys to select any item in the 
main menu. While making a selection on a particular page, press  
 or “Enter” key to enter sub menu.
3. Use   keys to select the desired item and adjust the settings 
using 
  key.
4.  Select the next item to be adjusted in the sub menu and adjust as 
described above.
5. Press “Enter” to confirm, and the screen will return to the main 
menu.
6. To exit, press “MENU” again. The OSD menu will close and the 
projector will automatically save the new settings.
On-screen Display Menus
Main Menu
Sub Menu Settings        
						

							25English
User Controls
Menu Tree
Main Menu Sub Menu Settings
ImageDisplay Mode
Brightness
³
Contrast ³
Sharpness
Saturation
Tint
Advanced Film / Video / Graphics / PC
0~10
Color Temp. Warm / Medium / Cold
Color
Color Space AUTO / RGB / YUV
Input Source VGA1 / VGA2 / Video / S-Video / HDMI
Image AI On / Off
Exit
DisplayFormat 4:3 / 16:9-1 / 16:9-II / Native / AUTO
4:3 / 16:9 / 16:10 / LBX / Native / AUTO
0~10
Zoom 80%~200%
H Image Shift -50 ~ +50
V Image Shift -50 ~ +50
V Keystone -40 ~ +40
Auto Keystone On / Off
3D 3D Off / On
3D Sync. Invert On / Off
Exit
SetupLanguage
Screen Type 16:10 / 16:9
Projection
Menu Location
Signal Automatic On / Off
Phase (VGA) 0~31
Frequency (VGA) -5~5
H. Position (VGA) -5~5
V. Position (VGA) -5~5
Exit ³
Security Security On / Off
Security Timer Month / Day / Hour
Change Password ³
Exit Presentation / Bright / Movie / sRGB / 
Blackboard / Classroom / User / 3D
#1
#1
Degamma
BrilliantColor™ 
Red Gain / Green Gain / Blue Gain / Red 
Bias / Green Bias / Blue Bias / Cyan / 
Magenta / Yellow / Reset / Exit
#2
#3
Overscan
#4
English / Deutsch / Français / Italiano / 
Español / Português / Svenska / 
Nederlands / Norsk/Dansk / Polski / 
Suomi /  Jmkkdbc  / 
0  / Magyar / 
ý eština /  6
						

							26
English
User Controls
	 Please note that the on-screen display (OSD) menus vary according to the 
signal type selected and the projector model you are using.
	 (
#1) “Saturation” and “Tint” are only supported in Video mode. 
	 (
#2) For XGA model only.
	 (
#3) For WXGA model only. 16:9 or 16:10 depend on “Screen Type” setting.
	 (
#4) “3D Sync Invert” is only available when 3D is enabled. 
	 (
#5) “Signal” is only supported in Analog VGA (RGB) signal.
	 (
#6) MIC volume can also be controlled by setup 
 volume in OSD
Main Menu Sub Menu
Settings
SetupProjector ID0~99
Mute On / Off
Volume 0~10
Audio Input
Advanced Logo
Logo Capture
Closed Captioning Off / CC1 / CC2
Exit
RS232 RS232 / Network
Network Network State
DHCP
IP Address
Gateway
DNS
Apply Yes / No
Exit
OptionsSource Lock On / Off
High Altitude On / Off
Information Hide On / Off
Keypad Lock On / Off
Background Color Black / Red / Blue / Green / White
Advanced Direct Power On On / Off
Auto Power Off (min.) 0~180
Sleep Timer (min.) 0~995
Power Mode (Standby) Eco. / Active
Exit
Lamp Settings Lamp Hours Lamp Reminder On / Off
Brightness Mode STD/Bright
Lamp Reset Yes / No
Exit
Reset
#6
Default / Audio1(Phone jack) / Audio2 
(RCA R/L) / MIC
Optoma / User
Subnet mask 
						

							27English
User Controls
IMAGE
 Display Mode
There are many factory presets optimized for various types of   
images.
  Presentation: Good color and brightness from PC input.
 Bright: Maximum brightness from PC input.
 Moive: For home theater .
 sRGB: Standardised accurate color.
 Blackboard: This mode should be selected to achieve optimum 
color settings when projecting onto a blackboard (green).
 Classroom : This mode is recommended for projecting in a 
classroom.
  User: User’s settings.
 3D: Any further adjustments by the user in 3D will be saved in 
this mode for further use.
  Brightness
Adjust the brightness of the image.
 
 Press the  to darken image.
 
 Press the  to lighten the image.
  Contrast
The contrast controls the degree of difference between the lightest 
and darkest parts of the picture. 
 
  Press the  to decrease the contrast.
 
 Press the  to increase the contrast.     
						

							28
English
User Controls
  Sharpness
Adjust the sharpness of the image.
 
  Press the  to decrease the sharpness.
 
  Press the  to increase the sharpness. 
  Saturation
Adjust a video image from black and white to fully saturated color .
 
  Press the  to decrease the amount of saturation in the image.
 
  Press the  to increase the amount of saturation in the image. 
  Tint
Adjust the color balance of red and green.
 
  Press the  to increase the amount of green in the image.
 
  Press the  to increase the amount of red in the image. 
	 “Saturation” and 
“Tint” functions 
are only supported 
under Video mode.       
						

							29English
User Controls
IMAGE | Advanced
 Degamma
This allows you to choose a degamma table that has been   
fine-tuned to bring out the best image quality for the input.
 
  Film: for home theater.
 
 Video: for video or TV source.
 
 Graphics: for image source.
 
  PC: for PC or computer source.
  BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and 
system level enhancements to enable higher brightness while 
providing true, more vibrant colors in picture. The range is from 
“0” to “10”. If you prefer a stronger enhanced image, adjust toward 
the maximum setting. For a smoother, more natural image, adjust 
toward the minimum setting.
 Color Temp
If set to cold temperature, the image looks more blue. (cold image)
If set to warm temperature, the image looks more red.
(warm image)
 Color
Press  into  the  next  menu  as  below  and  then  use  or  
  to 
select item.
 
   Red/Green/Blue/Cyan/Magenta/Yellow : Use  or  to select 
Red, Green, Blue, Cyan, Magenta and Yellow Colors.
 
   Reset: Choose “Yes” to return the factory default settings for 
color adjustments.     
						

							30
English
User Controls
  Color Space
Select an appropriate color matrix type from AUTO, RGB or YUV.
 Input Source
Use this option to enable / disable input sources. Press  to enter 
the sub menu and select which sources you require. Press “Enter” 
to finalize the selection. The projector will not search for inputs that 
are not selected.
  Image AI
Image AI improves the contrast of the picture by optimizing the 
brightness of the lamp according to the picture content.
 On: The dynamic image performance manager is active in 
making sure your greatest pleasure from seeing a movie 
dynamically with the most dark details revealed, vivid and 
bright image performed all the way.
 Off: The dynamic image performance manager is on standby.