Optoma Projector Pro260x User Manual

							31English
User Controls
  3D Mode
  Off: Select “Off” to turn 3D settings off for 3D images.
  DLP Link: Select “DLP Link” to use optimized settings for DLP 
Link 3D images.
  IR: Select “IR” to use optimized settings for IR-based 3D 
images.
  3D Sync. Invert
 Press the “On” to invert left and right frame contents.
 Press the “Off” for default frame contents. 
	“IR” options may vary according to model.
	“3D Sync Invert” is only available when 3D is enabled and this mode 3D is for DLP link glass only.
	Compatible 3D source, 3D content and active shutter glasses are required for 3D viewing.
DISPLAY | 3D  
						

							32English
User Controls
SETUP
 Language
Choose the multilingual OSD menu. Press  or  into the sub 
menu and then use the  or  key to select your preferred  
language. Press “Enter” to finalize the selection. 
 Projection
    Front-Desktop
This is the default selection. The image is projected straight on 
the screen.
    Rear-Desktop
When selected, the image will appear reversed.
    Front-Ceiling 
When selected, the image will turn upside down.
	Rear-Desktop and Rear-Ceiling are to be used with a translucent screen.     
						

							33English
User Controls
    Rear-Ceiling 
When selected, the image will appear reversed in upside down 
position.
  Menu Location
Choose the menu location on the display screen.
 Screen Type
Choose the screen type from16:10 or 16:9.
 Projector ID
ID definition can be set up by menu (range 0-99), and allow user 
control an individual projector by RS232. Refer to page 52-55 for 
the complete list of RS232 commands.
 Mute
 Choose the “On” to turn mute on. 
 Choose the “Off” to turn mute off. 
 Volume
  Press the  to decrease the volume.
  Press the  to increase the volume.
	“Screen Type” is for WXGA only.   
						

							34English
User Controls
SETUP | Signal 
 (RGB)
 Automatic
Automatically selects the singal. If you use this function, the 
Phase, frequency items are grayed out, and if Signal is not auto-
matic, the phase, frequency items will appear for user to manually 
tune and saved in settings after that for next time projector turns 
off and on again.
 Phase
Synchronize the signal timing of the display with the graphic card. 
If the image appears to be unstable or flickers, use this function to 
correct it.
 Frequency
Change the display data frequency to match the frequency of 
your computer’s graphic card. Use this function only if the image 
appears to flicker vertically.
 H. Position
 Press the  to move the image left.
 Press the  to move the image right. 
 V. Position
 Press the  to move the image down.
 Press the  to move the image up. 
	“Signal” is only supported in Analog VGA (RGB) signal.     
						

							35English
User Controls
SETUP | Security
 Security
 On: Choose “On” to use security verification when the turning 
on the projector.
 Off: Choose “Off” to be able to switch on the projector without 
password verification.
 Security Timer
Use this function to set the how long (Month/Day/Hour) the 
projector can be used. Once this time has elapsed you will be  
requested to enter your password again.
 Change Password
 First time:
1.  Press “  ” to set the password.
2. The password has to be 4 digits. 
3. Use number button on the remote to enter your new 
password and then press “  ” key to confirm your 
password.
 Change Password:
1. Press “  ” to input old password.
2. Use number button to enter current password and then 
press “  ” to confirm. 
3. Enter new password (4 digits in length) using the number 
buttons on the remote, then press “  ” to confirm.
4. Enter new password again and press “  ” to confirm. 
	Password default value is “1234” (first time). 
						

							36English
User Controls
 If the incorrect password is entered 3 times, the projector will 
automatically shut down.
 If you have forgotten your password, please contact your local 
office for support.
  
						

							37English
User Controls
SETUP | Advanced
 Logo
Use this function to set the desired startup screen. If changes are 
made they will take effect the next time the projector is powered 
on.
 Optoma: The default startup screen.
 Neutral: Neutral startup screen.
 User: Use stored picture from “Logo Capture” function.
 Logo Capture
Press  to capture an image of the picture currently displayed
on screen.
 Closed Captioning
Use this function to set the desired startup screen. If changes are 
made they will take effect the next time the projector is powered 
on.
 Off: select “off” to turn off the closed captioning feature.
 CC1:CC1 language: American English.
 CC2:CC2 language (depending on the TV channel of the 
user):Spanish, French, Portuguese, German, Danish.
	For successful logo capture, please ensure that the onscreen image does not exceed the projector’s native resolution.  (SVGA:800x600 / XGA:1024x768 / WXGA:1280x800). 
						

							38English
User Controls
 Source Lock
 On: The projector will only search current input connection.
 Off: The projector will search for other signals if the current input signal is lost. 
  High Altitude
When “On” is selected, the fans will spin faster. This feature is 
useful in high altitude areas where the air is thin.
 Information Hide
 On: Choose “On” to hide the info message.
 Off: Choose “Off” to show the “searching” message.
 Keypad Lock
When the keypad lock function is “On”, the control panel will be 
locked however, the projector can be operated by the remote 
control. By selecting “Off”, you will be able to reuse the control 
panel.
  Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or 
“White”, screen when no signal is available.
 Test Pattern
Display a test pattern. There are Grid, White pattern and None.
 Reset
Choose “Yes” to return the display parameters on all menus to the 
factory default settings.
OPTIONS
	To turn off the key-pad lock, press and hold “Enter” key on top of the projector for 5 seconds.
	With dust filter installed, High Altitude mode must be turned on. Dust filter is Optional and may not be required in some regions. 
						

							39English
User Controls
OPTIONS | 
Advanced
 Direct Power On
Choose “On” to activate Direct Power mode. The projector will 
automatically power on when AC power is supplied, without 
pressing the “” key on the projector control panel or on the 
remote control.
 Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, 
when there is no signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes).
 Sleep Timer (min)
Sets the countdown timer interval. The countdown timer will start, 
with or without a signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes).
 Power Mode (Standby)
 Eco.: Choose “Eco.” to save power dissipation further < 1W.
 Active: Choose “Active” to return to normal standby and the 
VGA out port will be enabled. 
	When Power mode (Standby) is set to Eco (
						

							40English
User Controls
OPTIONS |  
Lamp Settings
 Lamp Hours
Display the projection time.
 Lamp Reminder
Choose this function to show or to hide the warning message 
when the changing lamp message is displayed.  
The message will appear 30 hours before suggested replacement 
of lamp.
 Brightness Mode
 STD: Choose “STD” to dim the projector lamp which will lower 
power consumption and extend the lamp life. 
 BRIGHT: Choose “BRIGHT” to increase the brightness. 
 Lamp Reset
Reset the lamp hour counter after replacing the lamp.
	When ambient tem-perature is over 35°C in operating, the projector will switch to STD automatically.