Optoma Projector Hd91 User Manual
Have a look at the manual Optoma Projector Hd91 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1077 Optoma manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
51English Appendices Other Problems The projector stops responding to all controls If possible, turn off the projector, then unplug the power cord ` and wait at least 20 seconds before reconnecting power. Remote Control Problems If the remote control does not work Check the operating angle of the remote control is within ±25° ` both horizontally and vertically of on of the IR receivers on the projector. Make sure there are not any obstructions between the remote ` control and the projector. Move to within 6 m (20 ft) of the projector. Make sure batteries are inserted correctly. ` Replace batteries if they are exhausted. `
52English Appendices Power LED on: No ™signal; OSD menu appears and signal had been detected.Power LED off: ™Signal had been de-tected but OSD menu disappears. ＊ ON/STANDBY LED be ON when OSD appears, be OFF when OSD disappears. LED Lighting Messages MessagePower LED (Red) Power LED (Blue) Temp LED (Red)Standby State(Input power cord)Steady light *OffOff Power on (Warming)OffFlashingOff Power on and LED lightingOffSteady lightOff Power off (Cooling)OffFlashingOff Error (LED fail)FlashingOffOff Error (Fan fail)FlashingOffFlashing Error (Over Temp.)FlashingOffSteady light
53English Appendices Power off: ™ Power off? Press power key again LED warning: ™ LED Warning LED Life exceeded. Temperature warning: ™ Projector Overheated The projector will switch off autormatically Fan failed: ™ Fan Failure The projector will switch off autormatically Out of display range: ™ Video Out of range On Screen Messages
54English Appendices Computer/Video/HDMI/Mac Compatibility ™ Compatibility Modes (*1) 1920 x1200 ™@60Hz only support RB (reduced blank-ing).(*2) 3D timing for ™True 3D projector.(*3) is not supported ™HDMI input singal for Mac.120Hz input signals ™may be dependent on graphics cards support. SignalResolutionRefresh Rate (Hz)VideoAnalogHDMIMac NTSC720 x 48060O--- PAL/SECAM720 x 57650O--- VGA 640 x 48060-OOO 640 x 48067-O-- 640 x 48072.8-O-O 640 x 48085-O-O SVGA 800 x 60056.3-O-- 800 x 60060.3-OOO 800 x 60072.2-OOO 800 x 60085.1-OOO 800 x 600120 (*2)-OO- XGA 1024 x 76860-OOO 1024 x 76870.1-OOO 1024 x 76875-OOO 1024 x 76885-OOO 1024 x 768120 (*2)-OO- HDTV (720p) 1280 x 72050OOO- 1280 x 72060OOOO 1280 x 720120 (*2)-OO- WXGA 1280 x 76860-OOO (*3) 1280 x 76875-OOO 1280 x 76885-OOO (*3) 1280 x 80060-OOO SXGA 1280 x 102460-OOO 1280 x 102475-OOO 1280 x 102485-OO- SXGA+1400 x 105060-OO- UXGA1600 x120060-OO- HDTV (1080p) 1920 x 108024OOO- 1920 x 108030--O- 1920 x 108050OOO- 1920 x 108060OOOO HDTV (1080i)1920 x 108050O-O- 1920 x 108060O-O- WUXGA1920 x 120060 (*1)-OOO
55English Appendices SignalResolutionRefresh Rate (Hz)VideoAnalogHDMIMac SDTV (576i)720 x 57650O-O- SDTV (576p)720 x 57650O-O- SDTV (480i)720 x 48060O-O- SDTV (480p)720 x 48060O-O- 3D Input Video Compatibility ™ Input Resolution HDMI 1.4a 3D Input Input Timing 1280 x 720p @ 50HzTop-and-Bottom 1280 x 720p @ 60HzTop-and-Bottom 1280 x 720p @ 50HzFrame packing 1280 x 720p @ 60HzFrame packing 1920 x 1080i @ 50 HzSide-by-Side (Half) 1920 x 1080i @ 60 HzSide-by-Side (Half) 1920 x 1080p @ 24 HzTop-and-Bottom 1920 x 1080p @ 24 HzFrame packing HDMI 1.3 3D Content 1920 x 1080p @ 60Hz Side-by-Side (Half)While 3D Format is “SBS” 1920 x 1080i @ 50Hz 1920 x 1080i @ 60Hz 1280 x 720p @ 50Hz 1280 x 720p @ 60Hz 1920 x 1080p @ 60Hz Top-and-BottomWhile 3D Format is “Top and Bottom” 1920 x 1080i @ 50Hz 1920 x 1080i @ 60Hz 1280 x 720p @ 50Hz 1280 x 720p @ 60Hz 480iHQFSWhile 3D Format is “Frame sequential”
56English Appendices RS232 Pin Assignments Pin no.Spec. (from projector side) 1N/A 2RXD 3TXD 4N/A 5GND 6N/A 7N/A 8N/A 9N/A 1 2 3 4 5 6 7 8 9 RS232 Commands and Protocol Function List
57English Appendices RS232 Protocol Function List Baud Rate : 9600Data Bits: 8Parity: NoneStop Bits: 1 Flow Control : NoneUART16550 FIFO: Disable Projector Return (Pass): PProjector Return (Fail): F XX=00-99, projector's ID,XX=00 is for all projectors There is a after all ASCII commands.0D is the HEX code for in ASCII code. Optoma Data and HT ProjectorsHD91/HD90Baud Rate 9600 Data Bits 8 Parity None Stop Bits 1 Flow Control None UART16550 FIFO Disable ~ X X X XX nCR space variable carriage return ASCII Pass Fail Power On/Off n=1/n=0 & 2 ~XX00 nPF Re-sync ~XX01 nP F HDMI 1 n=1~XX12 n P VGA n=5 VGA Com ponent n=8 Video n=10 Component RCA n=14 HDMI 2 n=15 Cinema n=1~XX20 n P F Film n=11 Bright n=2 Photo n=3 Reference n=4 User n=5 ISF Day n=7 ISF Night n=8 3D n=9 Brightness n= -50 - +50 ~XX21 nPF Contrast n= -50 - +50 ~XX22 nPF Sharpness n= 0 - +15~XX23 n P F Tint n= -50 - +50 ~XX44 nPF Color n= -50 - +50 ~XX45 nPF Red Gain n= -50 - +50~XX24 n Green Gain n= -50 - +50 ~XX25 n Blue Gain n= -50 - +50 ~XX26 n Red Bias n= -50 - +50 ~XX27 n Green Bias n= -50 - +50 ~XX28 n Blue Bias n= -50 - +50 ~XX29 n Reset n=1~XX33 n D50 n=1~XX210 n D65 n=2~XX210 n D75 n=4~XX210 n D83 n=5~XX210 n D93 n=6~XX210 n Native n=7~XX210 n Native n=1~XX211 n Adobe n=6~XX211 n DLP Cinema n=2~XX211 n HDTV n=3~XX211 n SMPT-C n=5~XX211 n Red n=1~XX212 n Green n=2~XX212 n Blue n=3~XX212 n Cyan n=4~XX212 n Yellow n=5~XX212 n Magenta n=6~XX212 n x offset -50 ~ 50 n= -50 - +50 ~XX213 n y offset -50 ~ 50n= -50 - +50 ~XX214 n Brightness -50 ~ 50n= -50 - +50 ~XX217 n Reset n=1~XX215 n Film n=1~XX35 n P F Curve Type Film/Video/Graphics/1.8 /1.9/2.0/2.1/2.2/2.3/2.4/2.5/2.6 n=-5 - +6 ~XX182 n Offset n=-5 - +5~XX183 n Reset n=1~XX206 n Video n=2~XX35 n Curve Type Film/Video/Graphics/1.8 /1.9/2.0/2.1/2.2/2.3/2.4/2.5/2.6 n=-5 - +6 ~XX184 n Offset n=-5 - +5~XX185 n Reset n=1~XX207 n Graphics n=3~XX35 n Curve Type Film/Video/Graphics/1.8 /1.9/2.0/2.1/2.2/2.3/2.4/2.5/2.6 n=-5 - +6 ~XX186 n Offset n=-5 - +5~XX187 n Reset n=1~XX208 n Standard n=4~XX35 n Curve Type Film/Video/Graphics/1.8 /1.9/2.0/2.1/2.2/2.3/2.4/2.5/2.6 n=-5 - +6 ~XX188 n Offset n=-5 - +5~XX189 n Reset n=1~XX209 n Auto n=1~XX37 n P F RGB (0-255)* * RGB (0-255) supports when HDMI is detected n=2 RGB(16 - 235)* *RGB(16 - 235)supports when HDMI is detected n=4 YUV n=3 Noise Reduction n= 0 - 10~XX196 n P F PureMotion OFF n=0~XX190 n LOW n=1~XX190 n MED n=2~XX190 n HIGH n=3~XX190 n UltraDetai lOFF n=0~XX41 n ON n=1~XX41 n HD+ n=2~XX41 n PureColor OFF n=0~XX42 n 1 n=1~XX42 n 2 n=2~XX42 n 3 n=3 ~XX42 n 4 n=4~XX42 n 5 n=5~XX42 n PureEn gine Demo OFF n=0~XX197 nH Splitn=1 P FV Split n=2 P F Power 100%/95%/90%/85%/ 80%/75%/70%/65%/ 60%/50% n=0/n=1/n=2/n=3/n=4 /n=5/n=6/n=7/n=8/n=9 ~XX326 n P F DynamicBlack 1 n=1PF DynamicBlack 2 n=2PF DynamicBlack 3 n=3PF 4:3 n=1~XX60 n P F 16:9 n=2 LBX n=5 Native n=6 Auto235 n=8 Auto235_Subtitle n=11 SuperWide n=9 Edge masking n=0-5~XX61 n P F ~XX191 n DISPLAY Don't support when Anamorphic lens is fixed Don't support when Anamorphic lens is motored or fixed LED Brightness Supportingit When Anamorphic lens is fixed or motor Don't support when Anamorphic lens is motored or fixed Projector ID Command ID Function Direct Source Commands Color Space Advanced Color Gamut PureEngine CMS Gamma IMAGE RGB Gain/Bias Color Temperature Display Mode Format Color Settings
58English Appendices ~X X X XX nCR space variable carriage return Projector ID Command ID Zoom n=0-10~XX62 n P F H Image Shift n= -100 - +100 ~XX63 nPF V Image Shift n= -100 - +100 ~XX64 nPF V Keystone n= -30 - +30 ~XX66 nPF 3D Mode DLP Link/VESA 3D n=1/n=2 ~XX230 n P F 3D->2D 3D / L / R 2D->2D; 3D->3D / 3D->L /3D->R n=1/n=2/n=3 ~XX400 n P F Auto n=0~XX405 n P F SBS n=1PF Top and Bottom n=2PF Frame Sequential n=3PF Lown=4 PFMidn=5 PFHighn=6 P F 3D Sync. Invert On/Off n=0/n=1~XX231 n Top Left n=1~XX72 n P F Top Right n=2 Centre n=3 Bottom Left n=4 Bottom Right n=5 LED Hours n=1~XX108 n Oknnnnn return LED hour Front-Desktop n=1~XX71 n P F Rear-Desktop n=2 Front-Ceiling n=3 Rear-Ceiling n=4 Test Pattern None / Grid / White Patter nn=0/n=1/n=2~XX195 n Blue n=1~XX104 n P F Black n=2 Gray n=6 IR Function All/Front/Top n=0 /n=1 / n=2 ~XX11 n P F 12V Trigger A Off\On n=0/n=1~XX192 n 12V Trigger B Off/On/Auto235/Auto 3D n=0/n=1/n=2/n=3~XX193 n 4:3 4:3 check ~XX205 0 4:3 unchec k~XX205 1 16:9 16:9 check ~XX205 2 16:9 uncheck ~XX205 3 Letter Box letter box check ~XX205 4 letter box unchec k~XX205 5 Nativenative check~XX205 6 native uncheck~XX205 7 ExitEnglish n=1~XX70 n P F German n=2 French n=3 Italian n=4 Spanish n=5 Portuguese n=6 Polish n=7 Dutch n=8 Swedish n=9 Norwegian/Danish n=10 Finnish n=11 Greek n=12 Traditional Chinese n=13 Simplified Chinese n=14 Japanese n=15 Korean n=16 Russian n=17 Hungarian n=18 Czech n=19 Arabic n=20 Thai n=21 Turkish n=22 HDMI 1 n=1~XX39 n P F HDMI 2 n=7 VGA n=5 3 x RCA Comnponent n=8 Video n=10 Source Lock On/Off n=1/n=0 & 2~XX100 n P F High Altitude On/Off n=1/n=0 & 2 ~XX101 nPF Information Hide On/Off n=1/n=0 & 2~XX102 n P F Auto Power Off (min) n=0-180~XX106 n P F Automatic Enable/Disable n=1/n=0 ~XX91 n Frequency\Tracking n=0~ 100~XX73 n P F Phase n= -50 - +50 ~XX74 nPF H. Position n= -50 - +50 ~XX75 nPF V. Position n= -50 - +50 ~XX76 nPF White level n=-50-+50 ~XX200 n Black level n=-50-+50 ~XX201 n Saturation -50~+50~XX202 n Hue -50~+50~XX203 n IRE 0 IRE / 7.5 IRE n=1/n=0~XX204 n Yes n=1 ~XX112 n P F No n=2 Information from Projector Automatically when: Standby Mode a=0INFOa Warming up a=1INFOa Cooling Down a=2INFOa Out of Range a=3INFOa LED Fail a=4 Thermal Switch Error a=5 Fan Lock a=6 Over Temperature a=7 Lamp Hours Running Out a=8 READ/Return Information from projector Information n=1~XX150 n Okabbbbbccddddee a = Power State Off\On a=0/1 b = LED Hour bbbbb c = Input Source Commands None c=00 VGA c=02 Video c=05 HDMI1 c=07 HDMI2 c=08 d = Firmware Version dddd e = Display mode None ee=0 Cinema ee=1 Bright ee=2 Film ee=11 Photo ee=3 Reference ee=4 User ee=5 ISF Day ee=7 ISF Night ee=8 3D ee=9 Model Name ~XX151 nOka Depends a=0/1/2 Language Projection When Movable lens is selected, 12V Trigger B won't accept any commands ) DISPLAY Background Color3D Format Decoding HDMI1.3 3D timing 2D->3DSYSTEM SETUP Menu Location Signal Input Source FIlters Reset 3D
59English Appendices ~X X X XX nCR space variable carriage return Projector ID Command ID RS232 Version No n=1~XX152 n Oka Depends a=??? Input Source Commands None/VGA/Video/HDMI1/ HDMI2/Component n=1 ~XX121 n Oka a=0/2//5//7/8/11 Software Version n=1~XX122 n Okdddd Display Mode None/Cinema/Bright/Photo/ Reference/User/ISF Day/ ISF Night/3D/Film n=1 ~XX123 n Oka a=0/1/2/3/4/5/7/8/9/11 Power State On/Off n=1~XX124 n Oka a=1/0 Brightness n=1~XX125 n Oka Contras tn=1 ~XX126 n Oka Aspect Ratio 4:3/16:9/LBX/Native/Auto235/ Auto235_Subtitle n=1 ~XX127 n Okaaa=1/2/5/6/8//9/11 for 4:3/16:9/LBX/ Native/Auto235/Auto235 Subtitle Color Temperature D50/D65/D70/D75/D83/D93/ Nativ en=1 ~XX128 n Oka a=1/2 /3/4/5/6/7 Projection Mode Front-Desktop Rear-Desktop Front-Ceiling Rear-Ceiling n=1 ~XX129 n Oka a=0/1/2/3 for Front- Desktop/Rear-Desktop /Front-Ceiling/Rear- Ceilin gRemote Control Up n=10~XX140 n Left n=11 Enter n=12 Right n=13 Down n=14 Menu n=20 Re-sync n=41
60English Appendices Please note that ™damage resulting from incorrect installation will void the warranty. Ceiling Mount Installation To prevent damage to your projector, please use the Optoma 1. ceiling mount. If you wish to use a third party ceiling mount kit, please ensure 2. the screws used to attach a mount to the projector meet the fol- lowing specifications: Screw type: M6 ` Maximum screw length: 12mm ` Minimum screw length: 10mm ` Warning: 1. If you buy a ceiling mount from another company, please be sure to use the correct screw size. Screw size will vary depending on the thickness of the mounting plate.2. Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.3. Avoid installing the projector near a heat source. Lens Unit: mm 138.5138.5 151.50 110.00110.00 148.5 66.0 172.1 12.9 24.5 442.3 344.2