Optoma Projector Hd91 User Manual

11English
Installation
3D S YN C
O ut  5 V  5
V P WROut  6 W (     ) (      )3
D S YN C
O ut  5 V  5
V P WROut  6 W (     ) (      )
m o l e
x
MOLEX
E62405SP
R
Connect to Computer/Notebook
Connecting the Projector
1
23
1....................................................................................................Power Cord2..................................................................................................*HDMI...

12English
Installation
3D S YN C
O ut  5 V  5
V P WROut  6 W (     ) (      )3
D S YN C
O ut  5 V  5
V P WROut  6 W (     ) (      )
E62405SP
R
Connect to Video Sources
1....................................................................................................Power Cord2..................................................................................................*HDMI Cable3........................................................................................*VGA/RCA...

13English
Installation
Connect to 3D Video Devices
The 3D video  ™source device must be powered on before the 3D projector.
If input video is  ™normal 2D, please press “3D Format” and switch to “Auto”.If “SBS Mode” is  ™active, 2D video content will not display correctly.
NOTE
NOTEOnce you have connected your devices together with HDMI 
cables, as shown in the diagram, you are ready to begin. 
Power ON your 3D video source and your 3D projector.
PlayStation® 3 GamesMake sure that you have...

14English
Installation
3D Broadcast3D Blu-ray™ Disc3D Console Games
SKY+HD, cable/satellite box3D Blu-ray™ Player
PlayStation® 3
3D Glasses
Full 3D 1080p DLP® Projector  

15English
Installation
To turn ON 3D glasses: Press the “Power” button and the LED will flash 1. one time indicating the glasses are ready to use 3D mode.Verify that 3D content is being sent to the projector and signal is compat-2. ible with projector specifications.Turn on the “3D Mode” (DLP-Link/VESA 3D - depending on which type 3. of glasses you are using) of the 3D projector. The option is located in the “Display” section of the projector OSD menu.Turn on 3D glasses and verify image appears in 3D...

16English
Installation
Powering On/Off the Projector
Turn on the projec- ™tor first and then select the signal sources.
Powering On the Projector
1. Remove the lens cap. 
2. Securely connect the power cord and signal cable. When 
connected, the Power LED will turn red. 
3. Turn on the projector by pressing “” button either on the 
side of the projector or on the remote. The Power LED will 
now turn blue. 
 The startup screen will display in approximately 10 seconds. 
The first time you use the...

17English
Installation
Powering Off the Projector
1.  Press the “  ” button on the remote control or “ 
” button on the side of the projector two times 
with one second interval to turn off the projector. 
The following message will be displayed on the screen. 
Power off?
Press power key again
   Press the “  ” button again to confirm otherwise the 
message will disappear after 15 seconds. When you press 
the “  ” button for the second time, the projector will shut 
down.
2. The cooling fans continue to...

18English
Installation
Contact the nearest  ™service center if the projector displays these symptoms. See pages 61-62 for more information.
Warning Indicator
When the warning indicators (see below) come on, 
the projector will automatically shutdown: 
™ “Power” LED indicator flashes red.
™ “TEMP” LED indicator is lit red and if “Power” LED indicator 
flashes red. This indicates the projector has overheated. 
Under normal conditions, the projector can be switched 
back on.
™ “TEMP” LED...

19English
Installation
Adjusting the Projected Image
Adjusting the Projector’s Height 
The projector is equipped with elevator feet for adjusting 
the image height.
1. Locate the adjustable foot you wish to modify on the 
underside of the projector. 
2. Rotate the adjustable ring clockwise to raise the projector 
or counter clockwise to lower it. Repeat with the remaining 
feet as needed. 
Tilt-Adjustment Feet
Tilt-Adjustment Ring  

20English
Installation
Zoom Ring
Adjusting the Projector’s Position
To determine where to position the projector, consider the size and 
shape of your screen, the location of your power outlets, and the dis-
tance between the projector and the rest of your equipment.
Focus Ring
Vertical Lens 
Shift Lever
Horizontal Lens
Shift Lever
10%W10%W
60%H
60%H
Width(W)Height (H)