Optoma Projector Hd8600 User Manual

							English

User Controls
 Source Lock
When this function is turned off, the projector will search for other 
signals if the current input signal is lost. When this function is 
turned on, it will search for a specified connection port.
 High Altitude
Choose “On” to turn on High Altitude mode. Operates the fans at 
full speed continuously to allow for proper high altitude cooling of 
the projector.
 Information Hide
Suppress informational messages on the projected screen.
 On: No status messages appear on screen during operation.
 Off: Status messages appear as normal on screen during   
operation.
  Auto Power Off
Set the time interval (in minutes) to power off the system if there is 
no input signal detected.
 Signal
      RGB/HDTV Source                         Video Source
     HDMI Source      
						

							
User Controls
 Frequency: Change the display data frequency to match the 
frequency of your computer’s graphic card. When you  
experience a vertical flickering bar, use this function to make an 
adjustment.
  Phase: Synchronize the signal timing of the display with the 
graphics card. If you experience an unstable or flickering   
image, use this function to correct it.
  H Position: Adjust the horizontal position.
 V Position: Adjust the vertical position.
 White Level : Allow user to adjust White Level when inputting 
SVideo or Video/CVBS signals.
 Black Level : Allow user to adjust Black Level when inputting 
SVideo or Video/CVBS signals.
 Saturation : Adjust a video image from black and white to fully 
saturated color. Press the 
 to decrease the amount of color in 
the image. Press the  to increase the amount of color in the 
image.
  Hue : Adjust the color balance of red and green. Press the  
to increase the amount of green in the image. Press the  to 
increase the amount of red in the image.
 IRE : Adjust measurement of composite video signals.
 Black Level (for HDMI): Allows user to adjust the Black Level 
for HDMI signals.
  Reset
Return the adjustments and settings to factory default values.
 Current : Return the current menu’s settings to factory default.
All : Return the settings for all menus to factory default values .
“IRE” is only supported 
on NTSC signal.
NoteNote      
						

							English

Appendices
Image Problems
 No image appears on-screen
 Ensure all the cables and power connections are correctly and securely connected as described in the “Installation” section.
 Ensure the pins of connectors are not crooked or broken.
 Check if the projection lamp has been securely installed. Please refer to the “Replacing the Lamp” section.
 Make sure you have removed the lens cap and the projector is switched on.
 Image is out of focus
  Make sure the Lens cap is removed.
 Adjust the Focus Ring on the projector lens.  
  Make sure the projection screen is between the required distance 
from the projector. See pages 21 and 22.
  The image is stretched when displaying 16:9 DVD title
 When you play anamorphic DVD or 16:9 DVD, the projector will 
show the best image in 16: 9 format on projector side.
 If you play the LBX format DVD title, please change the format a s 
LBX in projector OSD.
 If you play 4:3 format DVD title, please change the format as 4:3  in 
projector OSD.
 If the image is still stretched, you will also need to adjust the asp ect 
ratio by referring to the following:
 Please setup the display format as 16:9 (wide) aspect ratio type  on 
your DVD player.
Troubleshooting
 If you experience a problem with your projector, 
please refer to the following information. If a  
problem persists, please contact your local reseller 
or service center.       
						

							
Appendices
 Image is too small or too large
 Adjust the zoom lever from the lens.
 Move the projector closer to or further from the screen.
  Press [Menu] on the projector panel, go to “Display-->Format”.  
Try the different settings.
 Image has slanted sides:
  If possible, reposition the projector so that it is centered on the 
screen and below the bottom of the screen and use PureShift to 
make adjustments to the image position.
 Use “Display-->V Keystone” from the OSD to make an adjustment.
 Image is reversed
 Select “System-->Projection” from the OSD and adjust the  
projection direction.
Other Problems
 The projector stops responding to all controls
  If possible, turn off the projector, then unplug the power cord and 
wait at least 20 seconds before reconnecting power.
 Lamp burns out or makes a popping sound
 When the lamp reaches its end of life, it will burn out and may 
make a loud popping sound.  If this happens, the projector will not 
turn on until the lamp module has been replaced. To replace the 
lamp, follow the procedures in the “Replacing the Lamp” section on 
page 48.      
						

							English

Appendices
Projector Status Indication
Message
Power LED
(Blue)
Power LED
(Red)
Temp-LED“
(Red)
Lamp-LED
(Red)
Standby State  
(Input power cord)
Standby State  
(Burn in Mode)Flashing
Power on with OSD (Press power button) * 
Power on without OSD 
Over Temperature
Fan FailFlashing
Lamp error 
Power off (Cooling)
Steady light => No light => 
NoteNote
 * Power LED will be ON when OSD appears and OFF when OSD disappears.       
						

							
Appendices
 LED Error Code Messages
Error Code MessagePower LED
(Blink)
Lamp LED
(Blink)
T1 temperature over temperature
30
Thermal Break 40
G794 fail 44
T1 fail 45
Lamp error 50
Ballast Over Temperature 51
Ballast shot circuit in output detected 52
End of lamp lift detected 53
Ballast lamp did not ignite 54
Lamp extinguished during normal operation 55
Lamp extinguished during run-up phase 56
Fan1 error (Lamp Fan) 61
Fan2 error (Ballast Fan) 62
Fan3 error (Burner Fan) 63
Fan4 error (Power Fan) 64
Lamp door open 70
DMD error 80
Color wheel error 90      
						

							English

Appendices
 LED states
 On Screen Messages
  Fan failed: 
 The projector will switch off automatically.
 
 Over temperature: 
 The projector will switch off automatically.
 
 Replacing the lamp: 
 Lamp is approaching the end of its rated life. 
 Replacement suggested.
 
Remote Control Problems
 If the remote control does not work
 Check the operating angle of the remote control is within  ±15° b oth 
horizontally and vertically of on of the IR receivers on the projector .
 Make sure there are no any obstructions between the remote con-
trol and the projector. Move to within 7 m (23 ft) of the projector.
 Make sure batteries are inserted correctly.
 Replace batteries if they are exhausted.      
						

							
Appendices
Replacing the Lamp
The projector automatically detects the lamp life.  When the 
lamp life is nearing the end of use, you will receive a warning 
message.
When you see this message, please contact your local 
reseller or service center to change the lamp as soon as 
possible. Make sure the projector has been cooled down for 
at least 30 minutes before changing the lamp.  
Warning: Lamp compartment is hot!  Allow it to cool down before 
changing lamp!
Warning: To reduce the risk of personal injury, do not drop the lamp 
module or touch the lamp bulb. The bulb may shatter and cause 
injury if it is dropped.        
						

							English

Appendices
5
2
3
1
4      
						

							0
Appendices
Lamp Replacing Procedure: 
1.   Switch off the power to the projector by pressing the Power button.
2.   Allow the projector to cool down at least 30 minutes. 
3.   Disconnect the power cord.
4.   Unlock the lamp cover. 
5.   Pull up and remove the cover. 
6.   Use a screwdriver to remove the screws  from the lamp module. 
7.    Pull out the lamp module. 
To replace the lamp module, reverse the previous steps.
8.     Turn on the projector and do “Lamp Reset” after the lamp module is replaced.
Lamp Reset: (i)Press “Menu” -> (ii)Select “System” -> (iii)Select 
“Lamp Settings” ->(iv)Select “Lamp Reset” -> (v)Select “Yes”.