Optoma Projector Ew762 User Manual

							11English
Installation
VGA1-IN / YPbPr /
VGA2-IN
 / SCART / YPbPr
VGA-OUT S-VIDEO
VIDEO
AUDIO-OUT
(VGA 1)
AUDIO1-IN
RS-232
USB
(VGA 2)
AUDIO2-INHDMI
R-J45(S-VIDEO/VIDEO)
AUDIO3-IN
E62405SP
R
MOLEX
12V OUT1
4
2
3
76
5
89
Connect to Computer/Notebook
Connecting the Projector
	Due to the difference in applications for each country, some regions may have different accessories.
	(*) Optional accessory 
+12V Output
1....................................................................................................Power Cord2.....................................................................................................VGA Cable3..............................................................................................*Network Cable 4.....................................................................................................USB Cable 5...........................................................................................*DVI/HDMI Cable6................................................................................................*RS232 Cable7.........................................................................................*Audio Input Cable 8........................................................................................*VGA Output Cable9......................................................................................*Audio Output Cable
Audio Output   
						

							12English
Installation
Connect to Video Sources
	Due to the difference in applications for each country, some regions may have different accessories.
	(*) Optional accessory 
VGA1-IN / YPbPr /
VGA2-IN
 / SCART / YPbPr
VGA-OUT S-VIDEO
VIDEO
AUDIO-OUT
(VGA 1)
AUDIO1-IN
RS-232
USB
(VGA 2)
AUDIO2-INHDMI
R-J45(S-VIDEO/VIDEO)
AUDIO3-IN
E62405SP
R
12V OUT
1....................................................................................................Power Cord2.....................................................................................................VGA Cable 3................................................................................*Composite Video Cable4..............................................................................................*S-Video Cable5................................................*15-Pin to 3 RCA Component/HDTV Adaptor6.............................................................................*3 RCA Component Cable7...................................................................................*SCART/VGA Adaptor8.................................................................................*Audio Cable Jack/RCA9..................................................................................................*HDMI Cable10............................................................................................*Network Cable
Composite Video Output
DVD Player, Set-top Box, HDTV receiver
S-Video Output
1
3
4
6
2
7
5
8
8
8
910
DVD Player, Set-top Box, HDTV receiver
+12V Output         
						

							13English
Installation
Powering the projector On / Off
	Turn on the projector first and then select the signal sources.
Powering On the Projector
1. Remove the lens cap. 
2. Securely connect the power cord and signal cable. When 
connected, the POWER/STANDBY LED will turn Amber. 
3. Turn on the lamp by pressing “” button either on the top of 
the projector or on the remote. The POWER/STANDBY LED 
will now turn Green. 
 The startup screen will display in approximately 10 seconds. 
The first time you use the projector, you will be asked to 
select the preferred language and power saving mode. 
4. Turn on and connect the source that you want to display 
on the screen (computer, notebook, video player, etc). The 
projector will detect the source automatically. If not, push 
menu button and go to “OPTIONS”.  
Make sure that the “Source Lock” has been set to “Off”.
	If you connect multiple sources at the same time, press the 
“SOURCE” button on the control panel or direct source keys 
on the remote control to switch between inputs.
	When Power mode (Standby) is set to Eco (
						

							14English
Installation
	Contact the nearest service center if the projector displays these symptoms. See pages 64-65 for more information.
Warning Indicator
When the warning indicators (see below) come on, 
the projector will automatically shutdown: 
 “LAMP” LED indicator is lit red and if “POWER/STANDBY” 
indicator flashes amber.
 “TEMP” LED indicator is lit red and if “POWER/STANDBY” 
indicator flashes amber. This indicates the projector has 
overheated. Under normal conditions, the projector can be 
switched back on.
 “TEMP” LED indicator flashes red and if “POWER/STAND-
BY” indicator flashes amber.  
 Unplug the power cord from the projector, wait for 30 seconds 
and try again. If the warning indicator light up again, please 
contact your nearest service center for assistance. 
Powering Off the Projector
1.   Press the “” button on the remote control or 
on the control panel to turn off the projector. 
The following message will be displayed on the screen. 
  Press the “” button again to confirm otherwise the 
message will disappear after 15 seconds. When you 
press the “” button for the second time, the projector will 
display countdown timer and will shut down.
2. The cooling fans continue to operate for about 10 seconds 
for cooling cycle and the POWER/STANDBY LED will 
Flash Green. When the POWER/STANDBY LED lights 
solid Amber, the projector has entered standby mode.
 If you wish to turn the projector back on, you must wait 
until the projector has completed the cooling cycle and 
has entered standby mode. Once in standby mode, simply 
press “” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and 
the projector.
4. Do not turn on the projector immediately following a power 
off procedure. 
						

							15English
Installation
Adjusting the Projected Image
Adjusting the Projector’s Height 
The projector is equipped with elevator feet for adjusting 
the image height.
1. Locate the adjustable foot you wish to modify on the 
underside of the projector. 
2. Rotate the adjustable ring clockwise to raise the projector 
or counter clockwise to lower it. Repeat with the remaining 
feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring  
						

							16English
Installation
Adjusting the Projector’s Zoom / Focus
You may turn the zoom ring to zoom in or out. To focus the im-
age, rotate the focus ring until the image is clear.  
 WXGA series: The projector will focus at distances from 3.93 
to 32.8 feet (1.2 to 10.0 meters).
Adjusting Projection Image Size
 WXGA series: Projection Image Size from 36.3” to 362.0” 
(0.9 to 9.2 meters).
Width
Height
Diagonal
Top View
Side View Projection Distance (D)
Projection Distance (D) Screen
Screen
Screen (W)
Screen (H)
Offset (Hd)
POWER
?
Focus Ring
Zoom Ring                    
						

							17English
Installation
 This table is for user’s reference only.
WXGA
Diagonal length (inch) size of 16:10 Screen
Screen Size W x HProjection Distance (D)Offset (Hd)(m)(inch)(m)(feet)
WidthHeightWidthHeightwidetelewidetele(m)(feet)
44.00 0.95 0.59 37.40 23.23 1.20 1.50 3.94 4.92 0.07 0.24 
60.00 1.29 0.81 50.79 31.89 1.70 2.00 5.58 6.56 0.10 0.33 
70.00 1.51 0.94 59.45 37.01 1.90 2.30 6.23 7.54 0.12 0.38 
80.00 1.72 1.08 67.72 42.52 2.20 2.60 7.22 8.53 0.13 0.44 
90.00 1.94 1.21 76.38 47.64 2.50 3.00 8.20 9.84 0.15 0.49 
100.00 2.15 1.35 84.65 53.15 2.80 3.30 9.18 10.82 0.17 0.55 
120.00 2.58 1.62 101.57 63.78 3.30 4.00 10.82 13.12 0.20 0.66 
150.00 3.23 2.02 127.17 79.53 4.10 5.00 13.45 16.40 0.25 0.82 
180.00 3.88 2.42 152.76 95.28 5.00 6.00 16.40 19.68 0.30 0.98 
250.00 5.38 3.37 211.81 132.68 6.90 8.30 22.63 27.22 0.42 1.37 
302.00 6.50 4.07 255.91 160.24 8.30 10.00 27.22 32.80 0.50 1.66  
						

							18English
User Controls
Using the Control Panel
POWERRefer to the “Power On/Off the Projector” section on 
pages 13-14.
RE-SYNCAutomatically synchronize the projector to the input 
source.
EnterConfirm your item selection.
SOURCEPress “SOURCE” to select an input signal.
MenuPress “Menu” to launch the on-screen display 
(OSD) menu. To exit OSD, Press “Menu” again.
Four Directional 
Select KeysUse     to select items or make adjust-
ments to your selection.
KeystoneUse   to adjust image distortion caused 
by tilting the projector. (±40 degrees)
HELP?Help Menu (refer to page 21).
Lamp LEDIndicate the projector’s lamp status.
Temp LEDIndicate the projector’s temperature status. 
POWER/STANDBY LEDIndicate the projector’s status.
Control Panel
Control Panel & Remote Control
POWER?       
						

							19English
User Controls
Remote Control
Using the Remote Control
Power  
Refer to the “Power On/Off the Projector” 
section on pages 13-14.
Laser   Press to use laser pointer.
L ButtonMouse left click.
R ButtonMouse right click.
Page +Use this button to page up.
Page -Use this button to page down.
Enter  / Help Confirm your item selection.
 Help Menu (refer to page 21).
SourcePress “Source” to select an input signal.
Re-SYNC Automatically synchronizes the projector to 
the input source.
Four Directional 
Select KeysUse     to select items or make 
adjustments to your selection.
Keystone +/-Adjust image distortion caused by tilting the 
projector.
Volume +/-Adjust to increase / decrease the volume.
Brightness Adjust the brightness of the image.
3DPress the “3D” to turn the 3D OSD menu 
on/off.
Menu
Press “Menu” to launch the on-screen 
display (OSD) menu. To exit OSD, press 
“Menu” again.
HDMIPress “HDMI” to choose HDMI source.     
						

							20English
User Controls
Using the Remote Control
FreezePress “Freeze” to pause the screen image. 
Press this button again to unlock.
AV muteMomentarily turns off/on the audio and 
video.
S-Video Press “S-Video” to choose S-Video source.
VGAPress “VGA” to choose VGA sources.
VideoPress “Video” to choose Composite video 
source.